| Message ID | 1620990152-19255-2-git-send-email-dillon.minfei@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | Fix the i2c/clk bug of stm32 mcu platform | expand |
Hi Dillon When trying to applying this patch using "git am --3 <patch>" i got this error : error: cannot convert from y to UTF-8 fatal: could not parse patch Whereas i got no similar error with the other patch 2/3 and 4. I find a way to apply it anyway. Patrice On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote: > From: Dillon Min <dillon.minfei@gmail.com> > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > with mipi_dpi_interface driver, can support ili9341 with serial > mode or parallel rgb interface mode by register configuration. > > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > Link: https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@gmail.com/ > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > --- > drivers/gpu/drm/panel/Kconfig | 12 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++ > 3 files changed, 1298 insertions(+) > create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index 4894913936e9..e4babba17864 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -123,6 +123,18 @@ config DRM_PANEL_ILITEK_IL9322 > Say Y here if you want to enable support for Ilitek IL9322 > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. > > +config DRM_PANEL_ILITEK_ILI9341 > + tristate "Ilitek ILI9341 240x320 QVGA panels" > + depends on OF && SPI > + depends on DRM_KMS_HELPER > + depends on DRM_KMS_CMA_HELPER > + depends on BACKLIGHT_CLASS_DEVICE > + select DRM_MIPI_DBI > + help > + Say Y here if you want to enable support for Ilitek IL9341 > + QVGA (240x320) RGB panels. support serial & parallel rgb > + interface. > + > config DRM_PANEL_ILITEK_ILI9881C > tristate "Ilitek ILI9881C-based panels" > depends on OF > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index cae4d976c069..0ecde184665d 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o > +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > new file mode 100644 > index 000000000000..f84983cbb250 > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > @@ -0,0 +1,1285 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Ilitek ILI9341 TFT LCD drm_panel driver. > + * > + * This panel can be configured to support: > + * - 16-bit parallel RGB interface > + * - 18-bit parallel RGB interface > + * - 4-line serial spi interface > + * > + * Copyright (C) 2020 Dillon Min <dillon.minfei@gmail.com> > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c > + */ > + > +#include <linux/bitops.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/regulator/consumer.h> > +#include <linux/spi/spi.h> > +#include <linux/delay.h> > +#include <video/mipi_display.h> > +#include <drm/drm_mipi_dbi.h> > +#include <drm/drm_gem_framebuffer_helper.h> > +#include <drm/drm_gem_cma_helper.h> > +#include <drm/drm_fb_helper.h> > +#include <drm/drm_gem_atomic_helper.h> > +#include <drm/drm_atomic_helper.h> > + > +#include <drm/drm_drv.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > +#include <drm/drm_print.h> > + > +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ > +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ > +#define ILI9341_DFC 0xb6 /* Display Function Control register */ > +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ > +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ > +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ > +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ > +#define ILI9341_POWERA 0xcb /* Power control A register */ > +#define ILI9341_POWERB 0xcf /* Power control B register */ > +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ > +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ > +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ > +#define ILI9341_DTCB 0xea /* Driver timing control B */ > +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ > +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ > +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ > +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ > +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ > + > +#define ILI9341_MADCTL_BGR BIT(3) > +#define ILI9341_MADCTL_MV BIT(5) > +#define ILI9341_MADCTL_MX BIT(6) > +#define ILI9341_MADCTL_MY BIT(7) > + > + > +#define ILI9341_POWER_B_LEN 3 > +#define ILI9341_POWER_SEQ_LEN 4 > +#define ILI9341_DTCA_LEN 3 > +#define ILI9341_DTCB_LEN 2 > +#define ILI9341_POWER_A_LEN 5 > +#define ILI9341_DFC_1_LEN 2 > +#define ILI9341_FRC_LEN 2 > +#define ILI9341_VCOM_1_LEN 2 > +#define ILI9341_DFC_2_LEN 4 > +#define ILI9341_COLUMN_ADDR_LEN 4 > +#define ILI9341_PAGE_ADDR_LEN 4 > +#define ILI9341_INTERFACE_LEN 3 > +#define ILI9341_PGAMMA_LEN 15 > +#define ILI9341_NGAMMA_LEN 15 > +#define ILI9341_CA_LEN 3 > + > +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6)|BIT(4)) > +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6)|BIT(5)) > +#define ILI9341_GAMMA_CURVE_1 BIT(0) > +#define ILI9341_IF_WE_MODE BIT(0) > +#define ILI9341_IF_BIG_ENDIAN 0x00 > +#define ILI9341_IF_DM_RGB BIT(2) > +#define ILI9341_IF_DM_INTERNAL 0x00 > +#define ILI9341_IF_DM_VSYNC BIT(3) > +#define ILI9341_IF_RM_RGB BIT(1) > +#define ILI9341_IF_RIM_RGB 0x00 > + > +#define ILI9341_COLUMN_ADDR 0x00ef > +#define ILI9341_PAGE_ADDR 0x013f > + > +#define ILI9341_RGB_EPL BIT(0) > +#define ILI9341_RGB_DPL BIT(1) > +#define ILI9341_RGB_HSPL BIT(2) > +#define ILI9341_RGB_VSPL BIT(3) > +#define ILI9341_RGB_DE_MODE BIT(6) > +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) > + > +#define ILI9341_DBI_VCOMH_4P6V 0x23 > +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 > +#define ILI9341_DBI_PRC_NORMAL 0x20 > +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e > +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 > +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 > +#define ILI9341_DBI_FRC_DIVA 0x00 > +#define ILI9341_DBI_FRC_RTNA 0x1b > +#define ILI9341_DBI_EMS_GAS BIT(0) > +#define ILI9341_DBI_EMS_DTS BIT(1) > +#define ILI9341_DBI_EMS_GON BIT(2) > +/** > + * ili9341_command - ili9341 command with optional parameter(s) > + * @ili: struct ili9341 > + * @cmd: Command > + * @seq...: Optional parameter(s) > + * > + * Send command to the controller. > + * > + * Returns: > + * Zero on success, negative error code on failure. > + */ > +#define ili9341_command(ili, cmd, seq...) \ > +({ \ > + u8 d[] = { seq }; \ > + _ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \ > +}) > + > +/** > + * struct ili9341_config - the system specific ILI9341 configuration > + * @max_spi_speed: 10000000 > + */ > +struct ili9341_config { > + u32 max_spi_speed; > + /** @mode: the drm display mode */ > + const struct drm_display_mode mode; > + /** @ca: TODO: need comments for this register */ > + u8 ca[ILI9341_CA_LEN]; > + /** @power_b: TODO: need comments for this register */ > + u8 power_b[ILI9341_POWER_B_LEN]; > + /** @power_seq: TODO: need comments for this register */ > + u8 power_seq[ILI9341_POWER_SEQ_LEN]; > + /** @dtca: TODO: need comments for this register */ > + u8 dtca[ILI9341_DTCA_LEN]; > + /** @dtcb: TODO: need comments for this register */ > + u8 dtcb[ILI9341_DTCB_LEN]; > + /** @power_a: TODO: need comments for this register */ > + u8 power_a[ILI9341_POWER_A_LEN]; > + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ > + /* > + * Formula to calculate frame frequency: > + * Frame Rate=fosc/(Clocks per line x Division ratio x > + * (Lines+VBP+VFP)) > + * > + * Sets the division ratio for internal clocks of Normal mode at MCU > + * interface. > + * > + * fosc : internal oscillator frequency > + * Clocks per line : RTNA setting > + * Division ratio : DIVA setting > + * Lines : total driving line number > + * VBP : back porch line number > + * VFP : front porch line number > + * > + * RTNA [4:0] Frame Rate (Hz) RTNA [4:0] Frame Rate (Hz) > + * 1 0 0 0 0 119 1 1 0 0 0 79 > + * 1 0 0 0 1 112 1 1 0 0 1 76 > + * 1 0 0 1 0 106 1 1 0 1 0 73 > + * 1 0 0 1 1 100 1 1 0 1 1 70(default) > + * 1 0 1 0 0 95 1 1 1 0 0 68 > + * 1 0 1 0 1 90 1 1 1 0 1 65 > + * 1 0 1 1 0 86 1 1 1 0 1 63 > + * 1 0 1 1 1 83 1 1 1 1 1 61 > + * > + * DIVA [1:0] : division ratio for internal clocks when Normal mode. > + * > + * DIVA [1:0] Division Ratio > + * 0 0 fosc > + * 0 1 fosc / 2 > + * 1 0 fosc / 4 > + * 1 1 fosc / 8 > + * > + */ > + u8 frc[ILI9341_FRC_LEN]; > + /** @prc: TODO: need comments for this register */ > + u8 prc; > + /** @dfc_1: B6h DISCTRL (Display Function Control) */ > + /* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > + * Command 0 1 M XX 1 0 1 1 0 1 1 0 B6h > + * 1st Parameter 1 1 M XX 0 0 0 0 PTG[1:0] PT[1:0] 0A > + * 2nd Parameter 1 1 M XX REV GS SS SM ISC[3:0] 82 > + * 3rd Parameter 1 1 M XX 0 0 NL[5:0] 27 > + * 4th Parameter 1 1 M XX 0 0 PCDIV[5:0] XX > + * > + * PTG [1:0]: Set the scan mode in non-display area. > + * PTG1 | PTG0 | Gate outputs in | Source outputs in | VCOM output > + * non-display area | non-display area | > + * 1 0 Interval scan Set with the PT[2:0] bits > + * > + * PT [1:0]: Determine source/VCOM output in a non-display area in the > + * partial display mode. > + * 1 0 AGND AGND AGND AGND > + * > + * REV: Select whether the liquid crystal type is normally white type > + * or normally black type. > + * REV Liquid crystal type > + * 0 Normally black > + * 1 Normally white > + * > + * SS: Select the shift direction of outputs from the source driver. > + * SS Source Output Scan Direction > + * 0 S1 -> S720 > + * 1 S720 -> S1 > + * > + * GS: Sets the direction of scan by the gate driver in the range > + * determined by SCN [4:0] and NL [4:0]. The scan direction > + * determined by GS = 0 can be reversed by setting GS = 1. > + * > + * GS Gate Output Scan Direction > + * 0 G1 -> G320 > + * 1 G320 -> G1 > + */ > + u8 dfc_1[ILI9341_DFC_1_LEN]; > + /** @power_1: Power Control 1 (C0h) */ > + /* VRH [5:0]: Set the GVDD level, which is a reference level for the > + * VCOM level and the grayscale voltage level. > + * > + * VRH[5:0] GVDD VRH[5:0] GVDD > + * 0 0 0 0 0 0 Setting prohibited 1 0 0 0 0 0 4.45 V > + * 0 0 0 0 0 1 Setting prohibited 1 0 0 0 0 1 4.50 V > + * 0 0 0 0 1 0 Setting prohibited 1 0 0 0 1 0 4.55 V > + * 0 0 0 0 1 1 3.00 V 1 0 0 0 1 1 4.60 V > + * 0 0 0 1 0 0 3.05 V 1 0 0 1 0 0 4.65 V > + * 0 0 0 1 0 1 3.10 V 1 0 0 1 0 1 4.70 V > + * 0 0 0 1 1 0 3.15 V 1 0 0 1 1 0 4.75 V > + * 0 0 0 1 1 1 3.20 V 1 0 0 1 1 1 4.80 V > + * 0 0 1 0 0 0 3.25 V 1 0 1 0 0 0 4.85 V > + * 0 0 1 0 0 1 3.30 V 1 0 1 0 0 1 4.90 V > + * 0 0 1 0 1 0 3.35 V 1 0 1 0 1 0 4.95 V > + * 0 0 1 0 1 1 3.40 V 1 0 1 0 1 1 5.00 V > + * 0 0 1 1 0 0 3.45 V 1 0 1 1 0 0 5.05 V > + * 0 0 1 1 0 1 3.50 V 1 0 1 1 0 1 5.10 V > + * 0 0 1 1 1 0 3.55 V 1 0 1 1 1 0 5.15 V > + * 0 0 1 1 1 1 3.60 V 1 0 1 1 1 1 5.20 V > + * 0 1 0 0 0 0 3.65 V 1 1 0 0 0 0 5.25 V > + * 0 1 0 0 0 1 3.70 V 1 1 0 0 0 1 5.30 V > + * 0 1 0 0 1 0 3.75 V 1 1 0 0 1 0 5.35 V > + * 0 1 0 0 1 1 3.80 V 1 1 0 0 1 1 5.40 V > + * 0 1 0 1 0 0 3.85 V 1 1 0 1 0 0 5.45 V > + * 0 1 0 1 0 1 3.90 V 1 1 0 1 0 1 5.50 V > + * 0 1 0 1 1 0 3.95 V 1 1 0 1 1 0 5.55 V > + * 0 1 0 1 1 1 4.00 V 1 1 0 1 1 1 5.60 V > + * 0 1 1 0 0 0 4.05 V 1 1 1 0 0 0 5.65 V > + * 0 1 1 0 0 1 4.10 V 1 1 1 0 0 1 5.70 V > + * 0 1 1 0 1 0 4.15 V 1 1 1 0 1 0 5.75 V > + * 0 1 1 0 1 1 4.20 V 1 1 1 0 1 1 5.80 V > + * 0 1 1 1 0 0 4.25 V 1 1 1 1 0 0 5.85 V > + * 0 1 1 1 0 1 4.30 V 1 1 1 1 0 1 5.90 V > + * 0 1 1 1 1 0 4.35 V 1 1 1 1 1 0 5.95 V > + * 0 1 1 1 1 1 4.40 V 1 1 1 1 1 1 6.00 V > + */ > + u8 power_1; > + /** @power_2: Power Control 2 (C1h) */ > + /* > + * BT [2:0]: Sets the factor used in the step-up circuits. > + * Select the optimal step-up factor for the operating voltage. To > + * reduce power consumption, set a smaller factor. > + * > + * BT[2:0] AVDD VGH VGL > + * 0 0 0 VCI x 2 VCI x 7 VCI x 4 > + * 0 0 1 VCI x 3 > + * 0 1 0 VCI x 6 VCI x 4 > + * 0 1 1 VCI x 3 > + * > + */ > + u8 power_2; > + /** @vcom_1: VCOM Control 1(C5h) */ > + /* > + * VMH [6:0] : Set the VCOMH voltage > + * > + * VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH > + * 0000000 2.700 0100000 3.500 1000000 4.300 1100000 5.100 > + * 0000001 2.725 0100001 3.525 1000001 4.325 1100001 5.125 > + * 0000010 2.750 0100010 3.550 1000010 4.350 1100010 5.150 > + * 0000011 2.775 0100011 3.575 1000011 4.375 1100011 5.175 > + * 0000100 2.800 0100100 3.600 1000100 4.400 1100100 5.200 > + * 0000101 2.825 0100101 3.625 1000101 4.425 1100101 5.225 > + * 0000110 2.850 0100110 3.650 1000110 4.450 1100110 5.250 > + * 0000111 2.875 0100111 3.675 1000111 4.475 1100111 5.275 > + * 0001000 2.900 0101000 3.700 1001000 4.500 1101000 5.300 > + * 0001001 2.925 0101001 3.725 1001001 4.525 1101001 5.325 > + * 0001010 2.950 0101010 3.750 1001010 4.550 1101010 5.350 > + * 0001011 2.975 0101011 3.775 1001011 4.575 1101011 5.375 > + * 0001100 3.000 0101100 3.800 1001100 4.600 1101100 5.400 > + * 0001101 3.025 0101101 3.825 1001101 4.625 1101101 5.425 > + * 0001110 3.050 0101110 3.850 1001110 4.650 1101110 5.450 > + * 0001111 3.075 0101111 3.875 1001111 4.675 1101111 5.475 > + * 0010000 3.100 0110000 3.900 1010000 4.700 1110000 5.500 > + * 0010001 3.125 0110001 3.925 1010001 4.725 1110001 5.525 > + * 0010010 3.150 0110010 3.950 1010010 4.750 1110010 5.550 > + * 0010011 3.175 0110011 3.975 1010011 4.775 1110011 5.575 > + * 0010100 3.200 0110100 4.000 1010100 4.800 1110100 5.600 > + * 0010101 3.225 0110101 4.025 1010101 4.825 1110101 5.625 > + * 0010110 3.250 0110110 4.050 1010110 4.850 1110110 5.650 > + * 0010111 3.275 0110111 4.075 1010111 4.875 1110111 5.675 > + * 0011000 3.300 0111000 4.100 1011000 4.900 1111000 5.700 > + * 0011001 3.325 0111001 4.125 1011001 4.925 1111001 5.725 > + * 0011010 3.350 0111010 4.150 1011010 4.950 1111010 5.750 > + * 0011011 3.375 0111011 4.175 1011011 4.975 1111011 5.775 > + * 0011100 3.400 0111100 4.200 1011100 5.000 1111100 5.800 > + * 0011101 3.425 0111101 4.225 1011101 5.025 1111101 5.825 > + * 0011110 3.450 0111110 4.250 1011110 5.050 1111110 5.850 > + * 0011111 3.475 0111111 4.275 1011111 5.075 1111111 5.875 > + * > + * VML[6:0] : Set the VCOML voltage > + * > + * VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML > + * 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100 > + * 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075 > + * 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050 > + * 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025 > + * 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0 > + * 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved > + * 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved > + * 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved > + * 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved > + * 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved > + * 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved > + * 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved > + * 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved > + * 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved > + * 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved > + * 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved > + * 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved > + * 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved > + * 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved > + * 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved > + * 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved > + * 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved > + * 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved > + * 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved > + * 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved > + * 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved > + * 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved > + * 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved > + * 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved > + * 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved > + * 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved > + * 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved > + */ > + u8 vcom_1[ILI9341_VCOM_1_LEN]; > + /** @vcom_2: VCOM Control 2(C7h) */ > + /* > + * C7h VMCTRL1 (VCOM Control 1) > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > + * Command 0 1 M XX 1 1 0 0 0 1 1 1 C7h > + * Parameter 1 1 M XX nVM VMF[6:0] C0 > + * > + * nVM: nVM equals to “0” after power on reset and VCOM offset > + * equals to program MTP value. When nVM set to “1”, setting > + * of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted. > + * > + * VMF [6:0]: Set the VCOM offset voltage. > + */ > + u8 vcom_2; > + /** @address_mode: Memory Access Control (36h) */ > + /* > + * 36h MADCTL (Memory Access Control) > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > + * Command 0 1 M XX 0 0 1 1 0 1 1 0 36h > + * Parameter 1 1 M XX MY MX MV ML BGR MH 0 0 00 > + * > + * This command defines read/write scanning direction of frame memory. > + * This command makes no change on the other driver status. > + * > + * Bit Name Description > + * MY Row Address Order > + * MX Column Address Order > + * MV Row / Column Exchange These 3 bits control MCU to memory > + * write/read direction. > + * ML Vertical Refresh Order LCD vertical refresh direction control. > + * BGR RGB-BGR Order Color selector switch control > + * (0=RGB color filter panel, 1=BGR > + * color filter panel) > + * MH Horizontal Refresh ORDER LCD horizontal refreshing > + * direction control. > + * > + * Note: When BGR bit is changed, the new setting is active > + * immediately without update the content in Frame Memory again. > + * > + */ > + u8 address_mode; > + /** @g3amma_en: TODO: need comments for this register */ > + u8 g3amma_en; > + /** @rgb_interface: RGB Interface Signal Control (B0h) */ > + /* > + * B0h IFMODE (Interface Mode Control) > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > + * Command 0 1 M XX 1 0 1 1 0 0 0 0 B0h > + * Parameter 1 1 M XX ByPass_MODE RCM[1] RCM[0] 0 VSPL HSPL DPL EPL 40 > + * > + * Sets the operation status of the display interface. The setting > + * becomes effective as soon as the command is received. > + * EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low > + * enable for RGB interface) > + * > + * DPL: DOTCLK polarity set (“0”= data fetched at the rising time, > + * “1”= data fetched at the falling time) > + * > + * HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High > + * level sync clock) > + * > + * VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High > + * level sync clock) > + * > + * RCM [1:0]: RGB interface selection (refer to the RGB interface > + * section). > + * > + * ByPass_MODE: Select display data path whether Memory or Direct to > + * Shift register when RGB Interface is used. > + * > + * ByPass_MODE Display Data Path > + * 0 Direct to Shift Register (default) > + * 1 Memory > + */ > + u8 rgb_interface; > + /** @dfc_2: refer to dfc_1 */ > + u8 dfc_2[ILI9341_DFC_2_LEN]; > + /** @column_addr: Column Address Set (2Ah) */ > + /* This command is used to define area of frame memory where MCU can > + * access. This command makes no change on the > + * other driver status. The values of SC [15:0] and EC [15:0] are > + * referred when RAMWR command comes. Each value > + * represents one column line in the Frame Memory. > + */ > + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; > + /** @page_addr: Page Address Set (2Bh) */ > + /* This command is used to define area of frame memory where MCU can > + * access. This command makes no change on the > + * other driver status. The values of SP [15:0] and EP [15:0] are > + * referred when RAMWR command comes. Each value > + * represents one Page line in the Frame Memory. > + */ > + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; > + /** @interface: Interface Control (F6h) */ > + /* > + * F6h IFCTL (16bits Data Format Selection) > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > + * Command 0 1 M XX 1 1 1 1 0 1 1 0 F6h > + * 1stParameter 1 1 M XX MY MX MV > + * _EOR _EOR _EOR 0 BGR_EOR 0 0 WE MODE 01 > + * 2ndParameter 1 1 M XX 0 0 EPF[1] EPF[0] 0 0 MDT[1] MDT[0] 00 > + * 3rdParameter 1 1 M XX 0 0 ENDIAN 0 DM[1] DM[0] RM RIM 00 > + * > + */ > + u8 interface[ILI9341_INTERFACE_LEN]; > + /** @pixel_format: This command sets the pixel format for the RGB image data used by */ > + /* the interface. DPI [2:0] is the pixel format select of RGB > + * interface and DBI [2:0] is the pixel format of MCU interface. If a > + * particular interface, either RGB interface or MCU interface, is > + * not used then the corresponding bits in the parameter are ignored. > + * The pixel format is shown in the table below. > + * > + * DPI[2:0] RGB Interface Format DBI[2:0] MCU Interface Format > + * 0 0 0 Reserved 0 0 0 Reserved > + * 0 0 1 Reserved 0 0 1 Reserved > + * 0 1 0 Reserved 0 1 0 Reserved > + * 0 1 1 Reserved 0 1 1 Reserved > + * 1 0 0 Reserved 1 0 0 Reserved > + * 1 0 1 16 bits / pixel 1 0 1 16 bits / pixel > + * 1 1 0 18 bits / pixel 1 1 0 18 bits / pixel > + * 1 1 1 Reserved 1 1 1 Reserved > + * > + */ > + u8 pixel_format; > + /** @gamma_curve: This command is used to select the desired Gamma curve for the */ > + /* current display. A maximum of 4 fixed gamma curves can > + * be selected. The curve is selected by setting the appropriate bit > + * in the parameter as described in the Table: > + * > + * GC [7:0] Curve Selected > + * 01h Gamma curve 1 (G2.2) > + * 02h --- > + * 04h --- > + * 08h --- > + */ > + u8 gamma_curve; > + /** @pgamma: Positive Gamma Correction (E0h) */ > + /* > + * Set the gray scale voltage to adjust the gamma characteristics of > + * the TFT panel. > + */ > + u8 pgamma[ILI9341_PGAMMA_LEN]; > + /** @ngamma: Negative Gamma Correction (E1h) */ > + /* > + * Set the gray scale voltage to adjust the gamma characteristics of > + * the TFT panel. > + */ > + u8 ngamma[ILI9341_NGAMMA_LEN]; > +}; > + > +struct ili9341 { > + struct device *dev; > + const struct ili9341_config *conf; > + struct drm_panel panel; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *dc_gpio; > + u32 max_spi_speed; > + struct regulator *vcc; > +}; > + > +/* > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller > + */ > +static const struct ili9341_config ili9341_stm32f429_disco_data = { > + .max_spi_speed = 10000000, > + .mode = { > + .clock = 6100, > + .hdisplay = 240, > + .hsync_start = 240 + 10,/* hfp 10 */ > + .hsync_end = 240 + 10 + 10,/* hsync 10 */ > + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ > + .vdisplay = 320, > + .vsync_start = 320 + 4,/* vfp 4 */ > + .vsync_end = 320 + 4 + 2,/* vsync 2 */ > + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ > + .flags = 0, > + .width_mm = 65, > + .height_mm = 50, > + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, > + }, > + /* TODO: need comments for this register */ > + .ca = {0xc3, 0x08, 0x50}, > + /* TODO: need comments for this register */ > + .power_b = {0x00, 0xc1, 0x30}, > + /* TODO: need comments for this register */ > + .power_seq = {0x64, 0x03, 0x12, 0x81}, > + /* TODO: need comments for this register */ > + .dtca = {0x85, 0x00, 0x78}, > + /* TODO: need comments for this register */ > + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, > + /* TODO: need comments for this register */ > + .prc = 0x20, > + /* TODO: need comments for this register */ > + .dtcb = {0x00, 0x00}, > + /* 0x00 fosc, 0x1b 70hz */ > + .frc = {0x00, 0x1b}, > + /* 0x0a Interval scan, AGND AGND AGND AGND > + * 0xa2 Normally white, G1 -> G320, S720 -> S1, > + * Scan Cycle 5 frames,85ms > + */ > + .dfc_1 = {0x0a, 0xa2}, > + /* 0x10 3.65v */ > + .power_1 = 0x10, > + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ > + .power_2 = 0x10, > + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ > + .vcom_1 = {0x45, 0x15}, > + /* 0x90 offset voltage, VMH-48, VML-48 */ > + .vcom_2 = 0x90, > + /* 0xc8 Row Address Order, Column Address Order > + * BGR 1 > + */ > + .address_mode = 0xc8, > + .g3amma_en = 0x00, > + /* 0xc2 > + * Display Data Path: Memory > + * RGB: DE mode > + * DOTCLK polarity set (data fetched at the falling time) > + */ > + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | > + ILI9341_RGB_DE_MODE | > + ILI9341_RGB_DPL, > + /* > + * 0x0a > + * Gate outputs in non-display area: Interval scan > + * Determine source/VCOM output in a non-display area in the partial > + * display mode: AGND AGND AGND AGND > + * > + * 0xa7 > + * Scan Cycle: 15 frames > + * fFLM = 60Hz: 255ms > + * Liquid crystal type: Normally white > + * Gate Output Scan Direction: G1 -> G320 > + * Source Output Scan Direction: S720 -> S1 > + * > + * 0x27 > + * LCD Driver Line: 320 lines > + * > + * 0x04 > + * PCDIV: 4 > + */ > + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, > + /* column address: 240 */ > + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, > + ILI9341_COLUMN_ADDR & 0xff}, > + /* page address: 320 */ > + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, > + ILI9341_PAGE_ADDR & 0xff}, > + /* Memory write control: When the transfer number of data exceeds > + * (EC-SC+1)*(EP-SP+1), the column and page number will be > + * reset, and the exceeding data will be written into the following > + * column and page. > + * Display Operation Mode: RGB Interface Mode > + * Interface for RAM Access: RGB interface > + * 16- bit RGB interface (1 transfer/pixel) > + */ > + .interface = {ILI9341_IF_WE_MODE, 0x00, > + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, > + /* DPI: 16 bits / pixel */ > + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, > + /* Curve Selected: Gamma curve 1 (G2.2) */ > + .gamma_curve = ILI9341_GAMMA_CURVE_1, > + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, > + 0x09, 0x4e, 0x78, 0x3c, 0x09, > + 0x13, 0x05, 0x17, 0x11, 0x00}, > + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, > + 0x07, 0x31, 0x33, 0x42, 0x05, > + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, > +}; > + > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) > +{ > + return container_of(panel, struct ili9341, panel); > +} > + > +static int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz, > + u8 bpw, const void *buf, size_t len) > +{ > + size_t max_chunk = spi_max_transfer_size(spi); > + struct spi_transfer tr = { > + .bits_per_word = bpw, > + .speed_hz = speed_hz, > + .len = len, > + }; > + struct spi_message m; > + size_t chunk; > + int ret; > + > + spi_message_init_with_transfers(&m, &tr, 1); > + > + while (len) { > + chunk = min(len, max_chunk); > + > + tr.tx_buf = buf; > + tr.len = chunk; > + buf += chunk; > + len -= chunk; > + > + ret = spi_sync(spi, &m); > + if (ret) { > + dev_err(&spi->dev, "spi_sync error: %d\n", ret); > + return ret; > + } > + } > + return 0; > +} > + > +static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data, > + size_t count) > +{ > + struct spi_device *spi = to_spi_device(ili->dev); > + int ret = 0; > + > + gpiod_set_value_cansleep(ili->dc_gpio, 0); > + > + ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8, > + (const void *)&cmd, 1); > + if (ret || data == NULL || count == 0) { > + return ret; > + } > + > + gpiod_set_value_cansleep(ili->dc_gpio, 1); > + > + return ili9341_spi_transfer(spi, ili->max_spi_speed, 8, > + data, count); > +} > + > +static int ili9341_dpi_init(struct ili9341 *ili) > +{ > + int ret; > + ret = _ili9341_command(ili, 0xca, > + ili->conf->ca, > + ILI9341_CA_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_POWERB, > + ili->conf->power_b, > + ILI9341_POWER_B_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_POWER_SEQ, > + ili->conf->power_seq, > + ILI9341_POWER_SEQ_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_DTCA, > + ili->conf->dtca, > + ILI9341_DTCA_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_POWERA, > + ili->conf->power_a, > + ILI9341_POWER_A_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_PRC, > + &ili->conf->prc, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_DTCB, > + ili->conf->dtcb, > + ILI9341_DTCB_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_FRC, > + ili->conf->frc, > + ILI9341_FRC_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_DFC, > + ili->conf->dfc_1, > + ILI9341_DFC_1_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_POWER1, > + &ili->conf->power_1, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_POWER2, > + &ili->conf->power_2, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_VCOM1, > + ili->conf->vcom_1, > + ILI9341_VCOM_1_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_VCOM2, > + &ili->conf->vcom_2, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE, > + &ili->conf->address_mode, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_3GAMMA_EN, > + &ili->conf->g3amma_en, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE, > + &ili->conf->rgb_interface, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_DFC, > + ili->conf->dfc_2, > + ILI9341_DFC_2_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS, > + ili->conf->column_addr, > + ILI9341_COLUMN_ADDR_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS, > + ili->conf->page_addr, > + ILI9341_PAGE_ADDR_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_INTERFACE, > + ili->conf->interface, > + ILI9341_INTERFACE_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT, > + &ili->conf->pixel_format, > + 1); > + if (ret) > + return ret; > + > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); > + if (ret) > + return ret; > + > + msleep(200); > + ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE, > + &ili->conf->gamma_curve, > + 1); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_PGAMMA, > + ili->conf->pgamma, > + ILI9341_PGAMMA_LEN); > + if (ret) > + return ret; > + > + ret = _ili9341_command(ili, ILI9341_NGAMMA, > + ili->conf->ngamma, > + ILI9341_NGAMMA_LEN); > + if (ret) > + return ret; > + > + ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE); > + if (ret) > + return ret; > + > + msleep(200); > + ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); > + if (ret) > + return ret; > + > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); > + if (ret) > + return ret; > + > + dev_info(ili->dev, "initialized display rgb interface\n"); > + > + return 0; > +} > + > +static int ili9341_dpi_power_on(struct ili9341 *ili) > +{ > + int ret = 0; > + > + /* Assert RESET */ > + gpiod_set_value(ili->reset_gpio, 1); > + > + /* Enable power */ > + if (!IS_ERR(ili->vcc)) { > + ret = regulator_enable(ili->vcc); > + if (ret < 0) { > + dev_err(ili->dev, "unable to enable vcc\n"); > + return ret; > + } > + } > + msleep(20); > + > + /* De-assert RESET */ > + gpiod_set_value(ili->reset_gpio, 0); > + msleep(10); > + > + return 0; > +} > + > +static int ili9341_dpi_power_off(struct ili9341 *ili) > +{ > + /* Assert RESET */ > + gpiod_set_value(ili->reset_gpio, 1); > + > + /* Disable power */ > + if (!IS_ERR(ili->vcc)) > + return regulator_disable(ili->vcc); > + > + return 0; > +} > + > +static int ili9341_dpi_disable(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF); > + > + return 0; > +} > + > +static int ili9341_dpi_unprepare(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + return ili9341_dpi_power_off(ili); > +} > + > +static int ili9341_dpi_prepare(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + int ret; > + > + ret = ili9341_dpi_power_on(ili); > + if (ret < 0) > + return ret; > + > + ret = ili9341_dpi_init(ili); > + if (ret < 0) > + ili9341_dpi_unprepare(panel); > + > + return ret; > +} > + > +static int ili9341_dpi_enable(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); > + > + return 0; > +} > + > +static int ili9341_dpi_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + struct drm_device *drm = connector->dev; > + struct drm_display_mode *mode; > + struct drm_display_info *info; > + > + info = &connector->display_info; > + info->width_mm = ili->conf->mode.width_mm; > + info->height_mm = ili->conf->mode.height_mm; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; > + else > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; > + else > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; > + > + mode = drm_mode_duplicate(drm, &ili->conf->mode); > + if (!mode) { > + DRM_ERROR("bad mode or failed to add mode\n"); > + return -EINVAL; > + } > + drm_mode_set_name(mode); > + > + /* Set up the polarity */ > + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) > + mode->flags |= DRM_MODE_FLAG_PHSYNC; > + else > + mode->flags |= DRM_MODE_FLAG_NHSYNC; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) > + mode->flags |= DRM_MODE_FLAG_PVSYNC; > + else > + mode->flags |= DRM_MODE_FLAG_NVSYNC; > + > + drm_mode_probed_add(connector, mode); > + > + return 1; /* Number of modes */ > +} > + > +static const struct drm_panel_funcs ili9341_dpi_funcs = { > + .disable = ili9341_dpi_disable, > + .unprepare = ili9341_dpi_unprepare, > + .prepare = ili9341_dpi_prepare, > + .enable = ili9341_dpi_enable, > + .get_modes = ili9341_dpi_get_modes, > +}; > + > +static int ili9341_dpi_probe(struct spi_device *spi) > +{ > + int ret; > + struct device *dev = &spi->dev; > + struct ili9341 *ili; > + > + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL); > + if (!ili) > + return -ENOMEM; > + > + spi_set_drvdata(spi, ili); > + > + ili->dev = dev; > + /* > + * Every new incarnation of this display must have a unique > + * data entry for the system in this driver. > + */ > + ili->conf = of_device_get_match_data(dev); > + if (!ili->conf) { > + dev_err(dev, "missing device configuration\n"); > + return -ENODEV; > + } > + > + ili->vcc = devm_regulator_get_optional(dev, "vcc"); > + if (IS_ERR(ili->vcc)) > + dev_err(dev, "get optional vcc failed\n"); > + > + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", > + GPIOD_OUT_HIGH); > + if (IS_ERR(ili->reset_gpio)) { > + dev_err(dev, "failed to get RESET GPIO\n"); > + return PTR_ERR(ili->reset_gpio); > + } > + > + ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW); > + if (IS_ERR(ili->dc_gpio)) { > + dev_err(dev, "failed to get DC GPIO\n"); > + return PTR_ERR(ili->dc_gpio); > + } > + > + spi->bits_per_word = 8; > + ret = spi_setup(spi); > + if (ret < 0) { > + dev_err(dev, "spi setup failed.\n"); > + return ret; > + } > + > + ili->max_spi_speed = ili->conf->max_spi_speed; > + > + drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs, > + DRM_MODE_CONNECTOR_DPI); > + > + drm_panel_add(&ili->panel); > + > + return 0; > +} > + > + > + > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, > + struct drm_crtc_state *crtc_state, > + struct drm_plane_state *plane_state) > +{ > + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); > + struct mipi_dbi *dbi = &dbidev->dbi; > + u8 addr_mode; > + int ret, idx; > + > + if (!drm_dev_enter(pipe->crtc.dev, &idx)) > + return; > + > + DRM_DEBUG_KMS("\n"); > + > + ret = mipi_dbi_poweron_conditional_reset(dbidev); > + if (ret < 0) > + goto out_exit; > + if (ret == 1) > + goto out_enable; > + > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); > + > + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); > + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); > + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); > + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); > + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); > + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); > + > + /* Power Control */ > + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); > + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); > + /* VCOM */ > + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, > + ILI9341_DBI_VCOM_1_VML_1P5V); > + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); > + > + /* Memory Access Control */ > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, > + MIPI_DCS_PIXEL_FMT_16BIT); > + > + /* Frame Rate */ > + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, > + ILI9341_DBI_FRC_RTNA & 0x1f); > + > + /* Gamma */ > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); > + mipi_dbi_command(dbi, ILI9341_PGAMMA, > + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, > + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); > + mipi_dbi_command(dbi, ILI9341_NGAMMA, > + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, > + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); > + > + /* DDRAM */ > + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | > + ILI9341_DBI_EMS_DTS | > + ILI9341_DBI_EMS_GON); > + > + /* Display */ > + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > + msleep(100); > + > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > + msleep(100); > + > +out_enable: > + switch (dbidev->rotation) { > + default: > + addr_mode = ILI9341_MADCTL_MX; > + break; > + case 90: > + addr_mode = ILI9341_MADCTL_MV; > + break; > + case 180: > + addr_mode = ILI9341_MADCTL_MY; > + break; > + case 270: > + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | > + ILI9341_MADCTL_MX; > + break; > + } > + addr_mode |= ILI9341_MADCTL_BGR; > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); > + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); > + DRM_DEBUG_KMS("initialized display serial interface\n"); > +out_exit: > + drm_dev_exit(idx); > +} > + > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { > + .enable = ili9341_dbi_enable, > + .disable = mipi_dbi_pipe_disable, > + .update = mipi_dbi_pipe_update, > + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, > +}; > + > +static const struct drm_display_mode ili9341_dbi_mode = { > + DRM_SIMPLE_MODE(240, 320, 37, 49), > +}; > + > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); > + > +static struct drm_driver ili9341_dbi_driver = { > + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, > + .fops = &ili9341_dbi_fops, > + DRM_GEM_CMA_DRIVER_OPS_VMAP, > + .debugfs_init = mipi_dbi_debugfs_init, > + .name = "ili9341", > + .desc = "Ilitek ILI9341", > + .date = "20180514", > + .major = 1, > + .minor = 0, > +}; > +static int ili9341_dbi_probe(struct spi_device *spi) > +{ > + struct mipi_dbi_dev *dbidev; > + struct drm_device *drm; > + struct mipi_dbi *dbi; > + struct gpio_desc *dc; > + struct device *dev = &spi->dev; > + u32 rotation = 0; > + int ret; > + > + dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver, > + struct mipi_dbi_dev, drm); > + if (IS_ERR(dbidev)) > + return PTR_ERR(dbidev); > + > + dbi = &dbidev->dbi; > + drm = &dbidev->drm; > + > + drm_mode_config_init(drm); > + > + dbi->reset = devm_gpiod_get_optional(dev, "reset", > + GPIOD_OUT_HIGH); > + if (IS_ERR(dbi->reset)) { > + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); > + return PTR_ERR(dbi->reset); > + } > + > + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); > + if (IS_ERR(dc)) { > + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); > + return PTR_ERR(dc); > + } > + > + dbidev->regulator = devm_regulator_get_optional(dev, "vcc"); > + if (IS_ERR(dbidev->regulator)) > + dev_err(dev, "get optional vcc failed\n"); > + > + dbidev->backlight = devm_of_find_backlight(dev); > + if (IS_ERR(dbidev->backlight)) > + return PTR_ERR(dbidev->backlight); > + > + device_property_read_u32(dev, "rotation", &rotation); > + > + ret = mipi_dbi_spi_init(spi, dbi, dc); > + if (ret) > + return ret; > + > + ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs, > + &ili9341_dbi_mode, rotation); > + if (ret) > + return ret; > + > + drm_mode_config_reset(drm); > + > + ret = drm_dev_register(drm, 0); > + if (ret) > + return ret; > + > + spi_set_drvdata(spi, drm); > + > + drm_fbdev_generic_setup(drm, 0); > + > + return 0; > +} > +static int ili9341_probe(struct spi_device *spi) > +{ > + const struct spi_device_id *id = spi_get_device_id(spi); > + > + if (!strcmp(id->name, "sf-tc240t-9370-t")) > + return ili9341_dpi_probe(spi); > + else if (!strcmp(id->name, "yx240qv29")) > + return ili9341_dbi_probe(spi); > + > + return -1; > +} > + > +static int ili9341_remove(struct spi_device *spi) > +{ > + const struct spi_device_id *id = spi_get_device_id(spi); > + struct ili9341 *ili = spi_get_drvdata(spi); > + struct drm_device *drm = spi_get_drvdata(spi); > + > + if (!strcmp(id->name, "sf-tc240t-9370-t")) { > + ili9341_dpi_power_off(ili); > + drm_panel_remove(&ili->panel); > + } else if (!strcmp(id->name, "yx240qv29")) { > + drm_dev_unplug(drm); > + drm_atomic_helper_shutdown(drm); > + } > + return 0; > +} > + > +static void ili9341_shutdown(struct spi_device *spi) > +{ > + const struct spi_device_id *id = spi_get_device_id(spi); > + > + if (!strcmp(id->name, "yx240qv29")) > + drm_atomic_helper_shutdown(spi_get_drvdata(spi)); > +} > + > +static const struct of_device_id ili9341_of_match[] = { > + { > + .compatible = "st,sf-tc240t-9370-t", > + .data = &ili9341_stm32f429_disco_data, > + }, > + { > + /* porting from tiny/ili9341.c > + * for original mipi dbi compitable > + */ > + .compatible = "adafruit,yx240qv29", > + .data = NULL, > + }, > +}; > +MODULE_DEVICE_TABLE(of, ili9341_of_match); > + > +static const struct spi_device_id ili9341_id[] = { > + { "yx240qv29", 0 }, > + { "sf-tc240t-9370-t", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(spi, ili9341_id); > + > +static struct spi_driver ili9341_driver = { > + .probe = ili9341_probe, > + .remove = ili9341_remove, > + .shutdown = ili9341_shutdown, > + .id_table = ili9341_id, > + .driver = { > + .name = "panel-ilitek-ili9341", > + .of_match_table = ili9341_of_match, > + }, > +}; > +module_spi_driver(ili9341_driver); > + > +MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>"); > +MODULE_DESCRIPTION("ILI9341 LCD panel driver"); > +MODULE_LICENSE("GPL v2"); >
On Mon, May 31, 2021 at 9:15 PM Patrice CHOTARD <patrice.chotard@foss.st.com> wrote: > > Hi Dillon > > When trying to applying this patch using "git am --3 <patch>" i got this error : > > error: cannot convert from y to UTF-8 > fatal: could not parse patch > > Whereas i got no similar error with the other patch 2/3 and 4. > > I find a way to apply it anyway. Sorry for the inconvenience, I will double verify the 'git am' process on this patch later. Thanks. Best Regards Dillon > > Patrice > > > On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote: > > From: Dillon Min <dillon.minfei@gmail.com> > > > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > > with mipi_dpi_interface driver, can support ili9341 with serial > > mode or parallel rgb interface mode by register configuration. > > > > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > > Link: https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@gmail.com/ > > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > > --- > > drivers/gpu/drm/panel/Kconfig | 12 + > > drivers/gpu/drm/panel/Makefile | 1 + > > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++ > > 3 files changed, 1298 insertions(+) > > create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > > index 4894913936e9..e4babba17864 100644 > > --- a/drivers/gpu/drm/panel/Kconfig > > +++ b/drivers/gpu/drm/panel/Kconfig > > @@ -123,6 +123,18 @@ config DRM_PANEL_ILITEK_IL9322 > > Say Y here if you want to enable support for Ilitek IL9322 > > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. > > > > +config DRM_PANEL_ILITEK_ILI9341 > > + tristate "Ilitek ILI9341 240x320 QVGA panels" > > + depends on OF && SPI > > + depends on DRM_KMS_HELPER > > + depends on DRM_KMS_CMA_HELPER > > + depends on BACKLIGHT_CLASS_DEVICE > > + select DRM_MIPI_DBI > > + help > > + Say Y here if you want to enable support for Ilitek IL9341 > > + QVGA (240x320) RGB panels. support serial & parallel rgb > > + interface. > > + > > config DRM_PANEL_ILITEK_ILI9881C > > tristate "Ilitek ILI9881C-based panels" > > depends on OF > > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > > index cae4d976c069..0ecde184665d 100644 > > --- a/drivers/gpu/drm/panel/Makefile > > +++ b/drivers/gpu/drm/panel/Makefile > > @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o > > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o > > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o > > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o > > +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o > > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o > > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o > > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o > > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > new file mode 100644 > > index 000000000000..f84983cbb250 > > --- /dev/null > > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > @@ -0,0 +1,1285 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > +/* > > + * Ilitek ILI9341 TFT LCD drm_panel driver. > > + * > > + * This panel can be configured to support: > > + * - 16-bit parallel RGB interface > > + * - 18-bit parallel RGB interface > > + * - 4-line serial spi interface > > + * > > + * Copyright (C) 2020 Dillon Min <dillon.minfei@gmail.com> > > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c > > + */ > > + > > +#include <linux/bitops.h> > > +#include <linux/gpio/consumer.h> > > +#include <linux/module.h> > > +#include <linux/of_device.h> > > +#include <linux/regulator/consumer.h> > > +#include <linux/spi/spi.h> > > +#include <linux/delay.h> > > +#include <video/mipi_display.h> > > +#include <drm/drm_mipi_dbi.h> > > +#include <drm/drm_gem_framebuffer_helper.h> > > +#include <drm/drm_gem_cma_helper.h> > > +#include <drm/drm_fb_helper.h> > > +#include <drm/drm_gem_atomic_helper.h> > > +#include <drm/drm_atomic_helper.h> > > + > > +#include <drm/drm_drv.h> > > +#include <drm/drm_modes.h> > > +#include <drm/drm_panel.h> > > +#include <drm/drm_print.h> > > + > > +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ > > +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ > > +#define ILI9341_DFC 0xb6 /* Display Function Control register */ > > +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ > > +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ > > +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ > > +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ > > +#define ILI9341_POWERA 0xcb /* Power control A register */ > > +#define ILI9341_POWERB 0xcf /* Power control B register */ > > +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ > > +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ > > +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ > > +#define ILI9341_DTCB 0xea /* Driver timing control B */ > > +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ > > +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ > > +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ > > +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ > > +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ > > + > > +#define ILI9341_MADCTL_BGR BIT(3) > > +#define ILI9341_MADCTL_MV BIT(5) > > +#define ILI9341_MADCTL_MX BIT(6) > > +#define ILI9341_MADCTL_MY BIT(7) > > + > > + > > +#define ILI9341_POWER_B_LEN 3 > > +#define ILI9341_POWER_SEQ_LEN 4 > > +#define ILI9341_DTCA_LEN 3 > > +#define ILI9341_DTCB_LEN 2 > > +#define ILI9341_POWER_A_LEN 5 > > +#define ILI9341_DFC_1_LEN 2 > > +#define ILI9341_FRC_LEN 2 > > +#define ILI9341_VCOM_1_LEN 2 > > +#define ILI9341_DFC_2_LEN 4 > > +#define ILI9341_COLUMN_ADDR_LEN 4 > > +#define ILI9341_PAGE_ADDR_LEN 4 > > +#define ILI9341_INTERFACE_LEN 3 > > +#define ILI9341_PGAMMA_LEN 15 > > +#define ILI9341_NGAMMA_LEN 15 > > +#define ILI9341_CA_LEN 3 > > + > > +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6)|BIT(4)) > > +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6)|BIT(5)) > > +#define ILI9341_GAMMA_CURVE_1 BIT(0) > > +#define ILI9341_IF_WE_MODE BIT(0) > > +#define ILI9341_IF_BIG_ENDIAN 0x00 > > +#define ILI9341_IF_DM_RGB BIT(2) > > +#define ILI9341_IF_DM_INTERNAL 0x00 > > +#define ILI9341_IF_DM_VSYNC BIT(3) > > +#define ILI9341_IF_RM_RGB BIT(1) > > +#define ILI9341_IF_RIM_RGB 0x00 > > + > > +#define ILI9341_COLUMN_ADDR 0x00ef > > +#define ILI9341_PAGE_ADDR 0x013f > > + > > +#define ILI9341_RGB_EPL BIT(0) > > +#define ILI9341_RGB_DPL BIT(1) > > +#define ILI9341_RGB_HSPL BIT(2) > > +#define ILI9341_RGB_VSPL BIT(3) > > +#define ILI9341_RGB_DE_MODE BIT(6) > > +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) > > + > > +#define ILI9341_DBI_VCOMH_4P6V 0x23 > > +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 > > +#define ILI9341_DBI_PRC_NORMAL 0x20 > > +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e > > +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 > > +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 > > +#define ILI9341_DBI_FRC_DIVA 0x00 > > +#define ILI9341_DBI_FRC_RTNA 0x1b > > +#define ILI9341_DBI_EMS_GAS BIT(0) > > +#define ILI9341_DBI_EMS_DTS BIT(1) > > +#define ILI9341_DBI_EMS_GON BIT(2) > > +/** > > + * ili9341_command - ili9341 command with optional parameter(s) > > + * @ili: struct ili9341 > > + * @cmd: Command > > + * @seq...: Optional parameter(s) > > + * > > + * Send command to the controller. > > + * > > + * Returns: > > + * Zero on success, negative error code on failure. > > + */ > > +#define ili9341_command(ili, cmd, seq...) \ > > +({ \ > > + u8 d[] = { seq }; \ > > + _ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \ > > +}) > > + > > +/** > > + * struct ili9341_config - the system specific ILI9341 configuration > > + * @max_spi_speed: 10000000 > > + */ > > +struct ili9341_config { > > + u32 max_spi_speed; > > + /** @mode: the drm display mode */ > > + const struct drm_display_mode mode; > > + /** @ca: TODO: need comments for this register */ > > + u8 ca[ILI9341_CA_LEN]; > > + /** @power_b: TODO: need comments for this register */ > > + u8 power_b[ILI9341_POWER_B_LEN]; > > + /** @power_seq: TODO: need comments for this register */ > > + u8 power_seq[ILI9341_POWER_SEQ_LEN]; > > + /** @dtca: TODO: need comments for this register */ > > + u8 dtca[ILI9341_DTCA_LEN]; > > + /** @dtcb: TODO: need comments for this register */ > > + u8 dtcb[ILI9341_DTCB_LEN]; > > + /** @power_a: TODO: need comments for this register */ > > + u8 power_a[ILI9341_POWER_A_LEN]; > > + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ > > + /* > > + * Formula to calculate frame frequency: > > + * Frame Rate=fosc/(Clocks per line x Division ratio x > > + * (Lines+VBP+VFP)) > > + * > > + * Sets the division ratio for internal clocks of Normal mode at MCU > > + * interface. > > + * > > + * fosc : internal oscillator frequency > > + * Clocks per line : RTNA setting > > + * Division ratio : DIVA setting > > + * Lines : total driving line number > > + * VBP : back porch line number > > + * VFP : front porch line number > > + * > > + * RTNA [4:0] Frame Rate (Hz) RTNA [4:0] Frame Rate (Hz) > > + * 1 0 0 0 0 119 1 1 0 0 0 79 > > + * 1 0 0 0 1 112 1 1 0 0 1 76 > > + * 1 0 0 1 0 106 1 1 0 1 0 73 > > + * 1 0 0 1 1 100 1 1 0 1 1 70(default) > > + * 1 0 1 0 0 95 1 1 1 0 0 68 > > + * 1 0 1 0 1 90 1 1 1 0 1 65 > > + * 1 0 1 1 0 86 1 1 1 0 1 63 > > + * 1 0 1 1 1 83 1 1 1 1 1 61 > > + * > > + * DIVA [1:0] : division ratio for internal clocks when Normal mode. > > + * > > + * DIVA [1:0] Division Ratio > > + * 0 0 fosc > > + * 0 1 fosc / 2 > > + * 1 0 fosc / 4 > > + * 1 1 fosc / 8 > > + * > > + */ > > + u8 frc[ILI9341_FRC_LEN]; > > + /** @prc: TODO: need comments for this register */ > > + u8 prc; > > + /** @dfc_1: B6h DISCTRL (Display Function Control) */ > > + /* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > > + * Command 0 1 M XX 1 0 1 1 0 1 1 0 B6h > > + * 1st Parameter 1 1 M XX 0 0 0 0 PTG[1:0] PT[1:0] 0A > > + * 2nd Parameter 1 1 M XX REV GS SS SM ISC[3:0] 82 > > + * 3rd Parameter 1 1 M XX 0 0 NL[5:0] 27 > > + * 4th Parameter 1 1 M XX 0 0 PCDIV[5:0] XX > > + * > > + * PTG [1:0]: Set the scan mode in non-display area. > > + * PTG1 | PTG0 | Gate outputs in | Source outputs in | VCOM output > > + * non-display area | non-display area | > > + * 1 0 Interval scan Set with the PT[2:0] bits > > + * > > + * PT [1:0]: Determine source/VCOM output in a non-display area in the > > + * partial display mode. > > + * 1 0 AGND AGND AGND AGND > > + * > > + * REV: Select whether the liquid crystal type is normally white type > > + * or normally black type. > > + * REV Liquid crystal type > > + * 0 Normally black > > + * 1 Normally white > > + * > > + * SS: Select the shift direction of outputs from the source driver. > > + * SS Source Output Scan Direction > > + * 0 S1 -> S720 > > + * 1 S720 -> S1 > > + * > > + * GS: Sets the direction of scan by the gate driver in the range > > + * determined by SCN [4:0] and NL [4:0]. The scan direction > > + * determined by GS = 0 can be reversed by setting GS = 1. > > + * > > + * GS Gate Output Scan Direction > > + * 0 G1 -> G320 > > + * 1 G320 -> G1 > > + */ > > + u8 dfc_1[ILI9341_DFC_1_LEN]; > > + /** @power_1: Power Control 1 (C0h) */ > > + /* VRH [5:0]: Set the GVDD level, which is a reference level for the > > + * VCOM level and the grayscale voltage level. > > + * > > + * VRH[5:0] GVDD VRH[5:0] GVDD > > + * 0 0 0 0 0 0 Setting prohibited 1 0 0 0 0 0 4.45 V > > + * 0 0 0 0 0 1 Setting prohibited 1 0 0 0 0 1 4.50 V > > + * 0 0 0 0 1 0 Setting prohibited 1 0 0 0 1 0 4.55 V > > + * 0 0 0 0 1 1 3.00 V 1 0 0 0 1 1 4.60 V > > + * 0 0 0 1 0 0 3.05 V 1 0 0 1 0 0 4.65 V > > + * 0 0 0 1 0 1 3.10 V 1 0 0 1 0 1 4.70 V > > + * 0 0 0 1 1 0 3.15 V 1 0 0 1 1 0 4.75 V > > + * 0 0 0 1 1 1 3.20 V 1 0 0 1 1 1 4.80 V > > + * 0 0 1 0 0 0 3.25 V 1 0 1 0 0 0 4.85 V > > + * 0 0 1 0 0 1 3.30 V 1 0 1 0 0 1 4.90 V > > + * 0 0 1 0 1 0 3.35 V 1 0 1 0 1 0 4.95 V > > + * 0 0 1 0 1 1 3.40 V 1 0 1 0 1 1 5.00 V > > + * 0 0 1 1 0 0 3.45 V 1 0 1 1 0 0 5.05 V > > + * 0 0 1 1 0 1 3.50 V 1 0 1 1 0 1 5.10 V > > + * 0 0 1 1 1 0 3.55 V 1 0 1 1 1 0 5.15 V > > + * 0 0 1 1 1 1 3.60 V 1 0 1 1 1 1 5.20 V > > + * 0 1 0 0 0 0 3.65 V 1 1 0 0 0 0 5.25 V > > + * 0 1 0 0 0 1 3.70 V 1 1 0 0 0 1 5.30 V > > + * 0 1 0 0 1 0 3.75 V 1 1 0 0 1 0 5.35 V > > + * 0 1 0 0 1 1 3.80 V 1 1 0 0 1 1 5.40 V > > + * 0 1 0 1 0 0 3.85 V 1 1 0 1 0 0 5.45 V > > + * 0 1 0 1 0 1 3.90 V 1 1 0 1 0 1 5.50 V > > + * 0 1 0 1 1 0 3.95 V 1 1 0 1 1 0 5.55 V > > + * 0 1 0 1 1 1 4.00 V 1 1 0 1 1 1 5.60 V > > + * 0 1 1 0 0 0 4.05 V 1 1 1 0 0 0 5.65 V > > + * 0 1 1 0 0 1 4.10 V 1 1 1 0 0 1 5.70 V > > + * 0 1 1 0 1 0 4.15 V 1 1 1 0 1 0 5.75 V > > + * 0 1 1 0 1 1 4.20 V 1 1 1 0 1 1 5.80 V > > + * 0 1 1 1 0 0 4.25 V 1 1 1 1 0 0 5.85 V > > + * 0 1 1 1 0 1 4.30 V 1 1 1 1 0 1 5.90 V > > + * 0 1 1 1 1 0 4.35 V 1 1 1 1 1 0 5.95 V > > + * 0 1 1 1 1 1 4.40 V 1 1 1 1 1 1 6.00 V > > + */ > > + u8 power_1; > > + /** @power_2: Power Control 2 (C1h) */ > > + /* > > + * BT [2:0]: Sets the factor used in the step-up circuits. > > + * Select the optimal step-up factor for the operating voltage. To > > + * reduce power consumption, set a smaller factor. > > + * > > + * BT[2:0] AVDD VGH VGL > > + * 0 0 0 VCI x 2 VCI x 7 VCI x 4 > > + * 0 0 1 VCI x 3 > > + * 0 1 0 VCI x 6 VCI x 4 > > + * 0 1 1 VCI x 3 > > + * > > + */ > > + u8 power_2; > > + /** @vcom_1: VCOM Control 1(C5h) */ > > + /* > > + * VMH [6:0] : Set the VCOMH voltage > > + * > > + * VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH > > + * 0000000 2.700 0100000 3.500 1000000 4.300 1100000 5.100 > > + * 0000001 2.725 0100001 3.525 1000001 4.325 1100001 5.125 > > + * 0000010 2.750 0100010 3.550 1000010 4.350 1100010 5.150 > > + * 0000011 2.775 0100011 3.575 1000011 4.375 1100011 5.175 > > + * 0000100 2.800 0100100 3.600 1000100 4.400 1100100 5.200 > > + * 0000101 2.825 0100101 3.625 1000101 4.425 1100101 5.225 > > + * 0000110 2.850 0100110 3.650 1000110 4.450 1100110 5.250 > > + * 0000111 2.875 0100111 3.675 1000111 4.475 1100111 5.275 > > + * 0001000 2.900 0101000 3.700 1001000 4.500 1101000 5.300 > > + * 0001001 2.925 0101001 3.725 1001001 4.525 1101001 5.325 > > + * 0001010 2.950 0101010 3.750 1001010 4.550 1101010 5.350 > > + * 0001011 2.975 0101011 3.775 1001011 4.575 1101011 5.375 > > + * 0001100 3.000 0101100 3.800 1001100 4.600 1101100 5.400 > > + * 0001101 3.025 0101101 3.825 1001101 4.625 1101101 5.425 > > + * 0001110 3.050 0101110 3.850 1001110 4.650 1101110 5.450 > > + * 0001111 3.075 0101111 3.875 1001111 4.675 1101111 5.475 > > + * 0010000 3.100 0110000 3.900 1010000 4.700 1110000 5.500 > > + * 0010001 3.125 0110001 3.925 1010001 4.725 1110001 5.525 > > + * 0010010 3.150 0110010 3.950 1010010 4.750 1110010 5.550 > > + * 0010011 3.175 0110011 3.975 1010011 4.775 1110011 5.575 > > + * 0010100 3.200 0110100 4.000 1010100 4.800 1110100 5.600 > > + * 0010101 3.225 0110101 4.025 1010101 4.825 1110101 5.625 > > + * 0010110 3.250 0110110 4.050 1010110 4.850 1110110 5.650 > > + * 0010111 3.275 0110111 4.075 1010111 4.875 1110111 5.675 > > + * 0011000 3.300 0111000 4.100 1011000 4.900 1111000 5.700 > > + * 0011001 3.325 0111001 4.125 1011001 4.925 1111001 5.725 > > + * 0011010 3.350 0111010 4.150 1011010 4.950 1111010 5.750 > > + * 0011011 3.375 0111011 4.175 1011011 4.975 1111011 5.775 > > + * 0011100 3.400 0111100 4.200 1011100 5.000 1111100 5.800 > > + * 0011101 3.425 0111101 4.225 1011101 5.025 1111101 5.825 > > + * 0011110 3.450 0111110 4.250 1011110 5.050 1111110 5.850 > > + * 0011111 3.475 0111111 4.275 1011111 5.075 1111111 5.875 > > + * > > + * VML[6:0] : Set the VCOML voltage > > + * > > + * VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML > > + * 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100 > > + * 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075 > > + * 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050 > > + * 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025 > > + * 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0 > > + * 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved > > + * 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved > > + * 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved > > + * 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved > > + * 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved > > + * 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved > > + * 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved > > + * 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved > > + * 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved > > + * 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved > > + * 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved > > + * 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved > > + * 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved > > + * 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved > > + * 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved > > + * 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved > > + * 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved > > + * 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved > > + * 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved > > + * 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved > > + * 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved > > + * 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved > > + * 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved > > + * 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved > > + * 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved > > + * 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved > > + * 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved > > + */ > > + u8 vcom_1[ILI9341_VCOM_1_LEN]; > > + /** @vcom_2: VCOM Control 2(C7h) */ > > + /* > > + * C7h VMCTRL1 (VCOM Control 1) > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > > + * Command 0 1 M XX 1 1 0 0 0 1 1 1 C7h > > + * Parameter 1 1 M XX nVM VMF[6:0] C0 > > + * > > + * nVM: nVM equals to “0” after power on reset and VCOM offset > > + * equals to program MTP value. When nVM set to “1”, setting > > + * of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted. > > + * > > + * VMF [6:0]: Set the VCOM offset voltage. > > + */ > > + u8 vcom_2; > > + /** @address_mode: Memory Access Control (36h) */ > > + /* > > + * 36h MADCTL (Memory Access Control) > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > > + * Command 0 1 M XX 0 0 1 1 0 1 1 0 36h > > + * Parameter 1 1 M XX MY MX MV ML BGR MH 0 0 00 > > + * > > + * This command defines read/write scanning direction of frame memory. > > + * This command makes no change on the other driver status. > > + * > > + * Bit Name Description > > + * MY Row Address Order > > + * MX Column Address Order > > + * MV Row / Column Exchange These 3 bits control MCU to memory > > + * write/read direction. > > + * ML Vertical Refresh Order LCD vertical refresh direction control. > > + * BGR RGB-BGR Order Color selector switch control > > + * (0=RGB color filter panel, 1=BGR > > + * color filter panel) > > + * MH Horizontal Refresh ORDER LCD horizontal refreshing > > + * direction control. > > + * > > + * Note: When BGR bit is changed, the new setting is active > > + * immediately without update the content in Frame Memory again. > > + * > > + */ > > + u8 address_mode; > > + /** @g3amma_en: TODO: need comments for this register */ > > + u8 g3amma_en; > > + /** @rgb_interface: RGB Interface Signal Control (B0h) */ > > + /* > > + * B0h IFMODE (Interface Mode Control) > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > > + * Command 0 1 M XX 1 0 1 1 0 0 0 0 B0h > > + * Parameter 1 1 M XX ByPass_MODE RCM[1] RCM[0] 0 VSPL HSPL DPL EPL 40 > > + * > > + * Sets the operation status of the display interface. The setting > > + * becomes effective as soon as the command is received. > > + * EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low > > + * enable for RGB interface) > > + * > > + * DPL: DOTCLK polarity set (“0”= data fetched at the rising time, > > + * “1”= data fetched at the falling time) > > + * > > + * HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High > > + * level sync clock) > > + * > > + * VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High > > + * level sync clock) > > + * > > + * RCM [1:0]: RGB interface selection (refer to the RGB interface > > + * section). > > + * > > + * ByPass_MODE: Select display data path whether Memory or Direct to > > + * Shift register when RGB Interface is used. > > + * > > + * ByPass_MODE Display Data Path > > + * 0 Direct to Shift Register (default) > > + * 1 Memory > > + */ > > + u8 rgb_interface; > > + /** @dfc_2: refer to dfc_1 */ > > + u8 dfc_2[ILI9341_DFC_2_LEN]; > > + /** @column_addr: Column Address Set (2Ah) */ > > + /* This command is used to define area of frame memory where MCU can > > + * access. This command makes no change on the > > + * other driver status. The values of SC [15:0] and EC [15:0] are > > + * referred when RAMWR command comes. Each value > > + * represents one column line in the Frame Memory. > > + */ > > + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; > > + /** @page_addr: Page Address Set (2Bh) */ > > + /* This command is used to define area of frame memory where MCU can > > + * access. This command makes no change on the > > + * other driver status. The values of SP [15:0] and EP [15:0] are > > + * referred when RAMWR command comes. Each value > > + * represents one Page line in the Frame Memory. > > + */ > > + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; > > + /** @interface: Interface Control (F6h) */ > > + /* > > + * F6h IFCTL (16bits Data Format Selection) > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX > > + * Command 0 1 M XX 1 1 1 1 0 1 1 0 F6h > > + * 1stParameter 1 1 M XX MY MX MV > > + * _EOR _EOR _EOR 0 BGR_EOR 0 0 WE MODE 01 > > + * 2ndParameter 1 1 M XX 0 0 EPF[1] EPF[0] 0 0 MDT[1] MDT[0] 00 > > + * 3rdParameter 1 1 M XX 0 0 ENDIAN 0 DM[1] DM[0] RM RIM 00 > > + * > > + */ > > + u8 interface[ILI9341_INTERFACE_LEN]; > > + /** @pixel_format: This command sets the pixel format for the RGB image data used by */ > > + /* the interface. DPI [2:0] is the pixel format select of RGB > > + * interface and DBI [2:0] is the pixel format of MCU interface. If a > > + * particular interface, either RGB interface or MCU interface, is > > + * not used then the corresponding bits in the parameter are ignored. > > + * The pixel format is shown in the table below. > > + * > > + * DPI[2:0] RGB Interface Format DBI[2:0] MCU Interface Format > > + * 0 0 0 Reserved 0 0 0 Reserved > > + * 0 0 1 Reserved 0 0 1 Reserved > > + * 0 1 0 Reserved 0 1 0 Reserved > > + * 0 1 1 Reserved 0 1 1 Reserved > > + * 1 0 0 Reserved 1 0 0 Reserved > > + * 1 0 1 16 bits / pixel 1 0 1 16 bits / pixel > > + * 1 1 0 18 bits / pixel 1 1 0 18 bits / pixel > > + * 1 1 1 Reserved 1 1 1 Reserved > > + * > > + */ > > + u8 pixel_format; > > + /** @gamma_curve: This command is used to select the desired Gamma curve for the */ > > + /* current display. A maximum of 4 fixed gamma curves can > > + * be selected. The curve is selected by setting the appropriate bit > > + * in the parameter as described in the Table: > > + * > > + * GC [7:0] Curve Selected > > + * 01h Gamma curve 1 (G2.2) > > + * 02h --- > > + * 04h --- > > + * 08h --- > > + */ > > + u8 gamma_curve; > > + /** @pgamma: Positive Gamma Correction (E0h) */ > > + /* > > + * Set the gray scale voltage to adjust the gamma characteristics of > > + * the TFT panel. > > + */ > > + u8 pgamma[ILI9341_PGAMMA_LEN]; > > + /** @ngamma: Negative Gamma Correction (E1h) */ > > + /* > > + * Set the gray scale voltage to adjust the gamma characteristics of > > + * the TFT panel. > > + */ > > + u8 ngamma[ILI9341_NGAMMA_LEN]; > > +}; > > + > > +struct ili9341 { > > + struct device *dev; > > + const struct ili9341_config *conf; > > + struct drm_panel panel; > > + struct gpio_desc *reset_gpio; > > + struct gpio_desc *dc_gpio; > > + u32 max_spi_speed; > > + struct regulator *vcc; > > +}; > > + > > +/* > > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller > > + */ > > +static const struct ili9341_config ili9341_stm32f429_disco_data = { > > + .max_spi_speed = 10000000, > > + .mode = { > > + .clock = 6100, > > + .hdisplay = 240, > > + .hsync_start = 240 + 10,/* hfp 10 */ > > + .hsync_end = 240 + 10 + 10,/* hsync 10 */ > > + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ > > + .vdisplay = 320, > > + .vsync_start = 320 + 4,/* vfp 4 */ > > + .vsync_end = 320 + 4 + 2,/* vsync 2 */ > > + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ > > + .flags = 0, > > + .width_mm = 65, > > + .height_mm = 50, > > + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, > > + }, > > + /* TODO: need comments for this register */ > > + .ca = {0xc3, 0x08, 0x50}, > > + /* TODO: need comments for this register */ > > + .power_b = {0x00, 0xc1, 0x30}, > > + /* TODO: need comments for this register */ > > + .power_seq = {0x64, 0x03, 0x12, 0x81}, > > + /* TODO: need comments for this register */ > > + .dtca = {0x85, 0x00, 0x78}, > > + /* TODO: need comments for this register */ > > + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, > > + /* TODO: need comments for this register */ > > + .prc = 0x20, > > + /* TODO: need comments for this register */ > > + .dtcb = {0x00, 0x00}, > > + /* 0x00 fosc, 0x1b 70hz */ > > + .frc = {0x00, 0x1b}, > > + /* 0x0a Interval scan, AGND AGND AGND AGND > > + * 0xa2 Normally white, G1 -> G320, S720 -> S1, > > + * Scan Cycle 5 frames,85ms > > + */ > > + .dfc_1 = {0x0a, 0xa2}, > > + /* 0x10 3.65v */ > > + .power_1 = 0x10, > > + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ > > + .power_2 = 0x10, > > + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ > > + .vcom_1 = {0x45, 0x15}, > > + /* 0x90 offset voltage, VMH-48, VML-48 */ > > + .vcom_2 = 0x90, > > + /* 0xc8 Row Address Order, Column Address Order > > + * BGR 1 > > + */ > > + .address_mode = 0xc8, > > + .g3amma_en = 0x00, > > + /* 0xc2 > > + * Display Data Path: Memory > > + * RGB: DE mode > > + * DOTCLK polarity set (data fetched at the falling time) > > + */ > > + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | > > + ILI9341_RGB_DE_MODE | > > + ILI9341_RGB_DPL, > > + /* > > + * 0x0a > > + * Gate outputs in non-display area: Interval scan > > + * Determine source/VCOM output in a non-display area in the partial > > + * display mode: AGND AGND AGND AGND > > + * > > + * 0xa7 > > + * Scan Cycle: 15 frames > > + * fFLM = 60Hz: 255ms > > + * Liquid crystal type: Normally white > > + * Gate Output Scan Direction: G1 -> G320 > > + * Source Output Scan Direction: S720 -> S1 > > + * > > + * 0x27 > > + * LCD Driver Line: 320 lines > > + * > > + * 0x04 > > + * PCDIV: 4 > > + */ > > + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, > > + /* column address: 240 */ > > + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, > > + ILI9341_COLUMN_ADDR & 0xff}, > > + /* page address: 320 */ > > + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, > > + ILI9341_PAGE_ADDR & 0xff}, > > + /* Memory write control: When the transfer number of data exceeds > > + * (EC-SC+1)*(EP-SP+1), the column and page number will be > > + * reset, and the exceeding data will be written into the following > > + * column and page. > > + * Display Operation Mode: RGB Interface Mode > > + * Interface for RAM Access: RGB interface > > + * 16- bit RGB interface (1 transfer/pixel) > > + */ > > + .interface = {ILI9341_IF_WE_MODE, 0x00, > > + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, > > + /* DPI: 16 bits / pixel */ > > + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, > > + /* Curve Selected: Gamma curve 1 (G2.2) */ > > + .gamma_curve = ILI9341_GAMMA_CURVE_1, > > + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, > > + 0x09, 0x4e, 0x78, 0x3c, 0x09, > > + 0x13, 0x05, 0x17, 0x11, 0x00}, > > + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, > > + 0x07, 0x31, 0x33, 0x42, 0x05, > > + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, > > +}; > > + > > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) > > +{ > > + return container_of(panel, struct ili9341, panel); > > +} > > + > > +static int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz, > > + u8 bpw, const void *buf, size_t len) > > +{ > > + size_t max_chunk = spi_max_transfer_size(spi); > > + struct spi_transfer tr = { > > + .bits_per_word = bpw, > > + .speed_hz = speed_hz, > > + .len = len, > > + }; > > + struct spi_message m; > > + size_t chunk; > > + int ret; > > + > > + spi_message_init_with_transfers(&m, &tr, 1); > > + > > + while (len) { > > + chunk = min(len, max_chunk); > > + > > + tr.tx_buf = buf; > > + tr.len = chunk; > > + buf += chunk; > > + len -= chunk; > > + > > + ret = spi_sync(spi, &m); > > + if (ret) { > > + dev_err(&spi->dev, "spi_sync error: %d\n", ret); > > + return ret; > > + } > > + } > > + return 0; > > +} > > + > > +static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data, > > + size_t count) > > +{ > > + struct spi_device *spi = to_spi_device(ili->dev); > > + int ret = 0; > > + > > + gpiod_set_value_cansleep(ili->dc_gpio, 0); > > + > > + ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8, > > + (const void *)&cmd, 1); > > + if (ret || data == NULL || count == 0) { > > + return ret; > > + } > > + > > + gpiod_set_value_cansleep(ili->dc_gpio, 1); > > + > > + return ili9341_spi_transfer(spi, ili->max_spi_speed, 8, > > + data, count); > > +} > > + > > +static int ili9341_dpi_init(struct ili9341 *ili) > > +{ > > + int ret; > > + ret = _ili9341_command(ili, 0xca, > > + ili->conf->ca, > > + ILI9341_CA_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_POWERB, > > + ili->conf->power_b, > > + ILI9341_POWER_B_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_POWER_SEQ, > > + ili->conf->power_seq, > > + ILI9341_POWER_SEQ_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_DTCA, > > + ili->conf->dtca, > > + ILI9341_DTCA_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_POWERA, > > + ili->conf->power_a, > > + ILI9341_POWER_A_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_PRC, > > + &ili->conf->prc, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_DTCB, > > + ili->conf->dtcb, > > + ILI9341_DTCB_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_FRC, > > + ili->conf->frc, > > + ILI9341_FRC_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_DFC, > > + ili->conf->dfc_1, > > + ILI9341_DFC_1_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_POWER1, > > + &ili->conf->power_1, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_POWER2, > > + &ili->conf->power_2, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_VCOM1, > > + ili->conf->vcom_1, > > + ILI9341_VCOM_1_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_VCOM2, > > + &ili->conf->vcom_2, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE, > > + &ili->conf->address_mode, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_3GAMMA_EN, > > + &ili->conf->g3amma_en, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE, > > + &ili->conf->rgb_interface, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_DFC, > > + ili->conf->dfc_2, > > + ILI9341_DFC_2_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS, > > + ili->conf->column_addr, > > + ILI9341_COLUMN_ADDR_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS, > > + ili->conf->page_addr, > > + ILI9341_PAGE_ADDR_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_INTERFACE, > > + ili->conf->interface, > > + ILI9341_INTERFACE_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT, > > + &ili->conf->pixel_format, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); > > + if (ret) > > + return ret; > > + > > + msleep(200); > > + ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE, > > + &ili->conf->gamma_curve, > > + 1); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_PGAMMA, > > + ili->conf->pgamma, > > + ILI9341_PGAMMA_LEN); > > + if (ret) > > + return ret; > > + > > + ret = _ili9341_command(ili, ILI9341_NGAMMA, > > + ili->conf->ngamma, > > + ILI9341_NGAMMA_LEN); > > + if (ret) > > + return ret; > > + > > + ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE); > > + if (ret) > > + return ret; > > + > > + msleep(200); > > + ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); > > + if (ret) > > + return ret; > > + > > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); > > + if (ret) > > + return ret; > > + > > + dev_info(ili->dev, "initialized display rgb interface\n"); > > + > > + return 0; > > +} > > + > > +static int ili9341_dpi_power_on(struct ili9341 *ili) > > +{ > > + int ret = 0; > > + > > + /* Assert RESET */ > > + gpiod_set_value(ili->reset_gpio, 1); > > + > > + /* Enable power */ > > + if (!IS_ERR(ili->vcc)) { > > + ret = regulator_enable(ili->vcc); > > + if (ret < 0) { > > + dev_err(ili->dev, "unable to enable vcc\n"); > > + return ret; > > + } > > + } > > + msleep(20); > > + > > + /* De-assert RESET */ > > + gpiod_set_value(ili->reset_gpio, 0); > > + msleep(10); > > + > > + return 0; > > +} > > + > > +static int ili9341_dpi_power_off(struct ili9341 *ili) > > +{ > > + /* Assert RESET */ > > + gpiod_set_value(ili->reset_gpio, 1); > > + > > + /* Disable power */ > > + if (!IS_ERR(ili->vcc)) > > + return regulator_disable(ili->vcc); > > + > > + return 0; > > +} > > + > > +static int ili9341_dpi_disable(struct drm_panel *panel) > > +{ > > + struct ili9341 *ili = panel_to_ili9341(panel); > > + > > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF); > > + > > + return 0; > > +} > > + > > +static int ili9341_dpi_unprepare(struct drm_panel *panel) > > +{ > > + struct ili9341 *ili = panel_to_ili9341(panel); > > + > > + return ili9341_dpi_power_off(ili); > > +} > > + > > +static int ili9341_dpi_prepare(struct drm_panel *panel) > > +{ > > + struct ili9341 *ili = panel_to_ili9341(panel); > > + int ret; > > + > > + ret = ili9341_dpi_power_on(ili); > > + if (ret < 0) > > + return ret; > > + > > + ret = ili9341_dpi_init(ili); > > + if (ret < 0) > > + ili9341_dpi_unprepare(panel); > > + > > + return ret; > > +} > > + > > +static int ili9341_dpi_enable(struct drm_panel *panel) > > +{ > > + struct ili9341 *ili = panel_to_ili9341(panel); > > + > > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); > > + > > + return 0; > > +} > > + > > +static int ili9341_dpi_get_modes(struct drm_panel *panel, > > + struct drm_connector *connector) > > +{ > > + struct ili9341 *ili = panel_to_ili9341(panel); > > + struct drm_device *drm = connector->dev; > > + struct drm_display_mode *mode; > > + struct drm_display_info *info; > > + > > + info = &connector->display_info; > > + info->width_mm = ili->conf->mode.width_mm; > > + info->height_mm = ili->conf->mode.height_mm; > > + > > + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; > > + else > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; > > + > > + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) > > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; > > + else > > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; > > + > > + mode = drm_mode_duplicate(drm, &ili->conf->mode); > > + if (!mode) { > > + DRM_ERROR("bad mode or failed to add mode\n"); > > + return -EINVAL; > > + } > > + drm_mode_set_name(mode); > > + > > + /* Set up the polarity */ > > + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) > > + mode->flags |= DRM_MODE_FLAG_PHSYNC; > > + else > > + mode->flags |= DRM_MODE_FLAG_NHSYNC; > > + > > + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) > > + mode->flags |= DRM_MODE_FLAG_PVSYNC; > > + else > > + mode->flags |= DRM_MODE_FLAG_NVSYNC; > > + > > + drm_mode_probed_add(connector, mode); > > + > > + return 1; /* Number of modes */ > > +} > > + > > +static const struct drm_panel_funcs ili9341_dpi_funcs = { > > + .disable = ili9341_dpi_disable, > > + .unprepare = ili9341_dpi_unprepare, > > + .prepare = ili9341_dpi_prepare, > > + .enable = ili9341_dpi_enable, > > + .get_modes = ili9341_dpi_get_modes, > > +}; > > + > > +static int ili9341_dpi_probe(struct spi_device *spi) > > +{ > > + int ret; > > + struct device *dev = &spi->dev; > > + struct ili9341 *ili; > > + > > + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL); > > + if (!ili) > > + return -ENOMEM; > > + > > + spi_set_drvdata(spi, ili); > > + > > + ili->dev = dev; > > + /* > > + * Every new incarnation of this display must have a unique > > + * data entry for the system in this driver. > > + */ > > + ili->conf = of_device_get_match_data(dev); > > + if (!ili->conf) { > > + dev_err(dev, "missing device configuration\n"); > > + return -ENODEV; > > + } > > + > > + ili->vcc = devm_regulator_get_optional(dev, "vcc"); > > + if (IS_ERR(ili->vcc)) > > + dev_err(dev, "get optional vcc failed\n"); > > + > > + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", > > + GPIOD_OUT_HIGH); > > + if (IS_ERR(ili->reset_gpio)) { > > + dev_err(dev, "failed to get RESET GPIO\n"); > > + return PTR_ERR(ili->reset_gpio); > > + } > > + > > + ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW); > > + if (IS_ERR(ili->dc_gpio)) { > > + dev_err(dev, "failed to get DC GPIO\n"); > > + return PTR_ERR(ili->dc_gpio); > > + } > > + > > + spi->bits_per_word = 8; > > + ret = spi_setup(spi); > > + if (ret < 0) { > > + dev_err(dev, "spi setup failed.\n"); > > + return ret; > > + } > > + > > + ili->max_spi_speed = ili->conf->max_spi_speed; > > + > > + drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs, > > + DRM_MODE_CONNECTOR_DPI); > > + > > + drm_panel_add(&ili->panel); > > + > > + return 0; > > +} > > + > > + > > + > > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, > > + struct drm_crtc_state *crtc_state, > > + struct drm_plane_state *plane_state) > > +{ > > + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); > > + struct mipi_dbi *dbi = &dbidev->dbi; > > + u8 addr_mode; > > + int ret, idx; > > + > > + if (!drm_dev_enter(pipe->crtc.dev, &idx)) > > + return; > > + > > + DRM_DEBUG_KMS("\n"); > > + > > + ret = mipi_dbi_poweron_conditional_reset(dbidev); > > + if (ret < 0) > > + goto out_exit; > > + if (ret == 1) > > + goto out_enable; > > + > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); > > + > > + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); > > + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); > > + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); > > + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); > > + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); > > + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); > > + > > + /* Power Control */ > > + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); > > + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); > > + /* VCOM */ > > + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, > > + ILI9341_DBI_VCOM_1_VML_1P5V); > > + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); > > + > > + /* Memory Access Control */ > > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, > > + MIPI_DCS_PIXEL_FMT_16BIT); > > + > > + /* Frame Rate */ > > + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, > > + ILI9341_DBI_FRC_RTNA & 0x1f); > > + > > + /* Gamma */ > > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); > > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); > > + mipi_dbi_command(dbi, ILI9341_PGAMMA, > > + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, > > + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); > > + mipi_dbi_command(dbi, ILI9341_NGAMMA, > > + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, > > + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); > > + > > + /* DDRAM */ > > + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | > > + ILI9341_DBI_EMS_DTS | > > + ILI9341_DBI_EMS_GON); > > + > > + /* Display */ > > + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); > > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > > + msleep(100); > > + > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > > + msleep(100); > > + > > +out_enable: > > + switch (dbidev->rotation) { > > + default: > > + addr_mode = ILI9341_MADCTL_MX; > > + break; > > + case 90: > > + addr_mode = ILI9341_MADCTL_MV; > > + break; > > + case 180: > > + addr_mode = ILI9341_MADCTL_MY; > > + break; > > + case 270: > > + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | > > + ILI9341_MADCTL_MX; > > + break; > > + } > > + addr_mode |= ILI9341_MADCTL_BGR; > > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); > > + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); > > + DRM_DEBUG_KMS("initialized display serial interface\n"); > > +out_exit: > > + drm_dev_exit(idx); > > +} > > + > > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { > > + .enable = ili9341_dbi_enable, > > + .disable = mipi_dbi_pipe_disable, > > + .update = mipi_dbi_pipe_update, > > + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, > > +}; > > + > > +static const struct drm_display_mode ili9341_dbi_mode = { > > + DRM_SIMPLE_MODE(240, 320, 37, 49), > > +}; > > + > > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); > > + > > +static struct drm_driver ili9341_dbi_driver = { > > + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, > > + .fops = &ili9341_dbi_fops, > > + DRM_GEM_CMA_DRIVER_OPS_VMAP, > > + .debugfs_init = mipi_dbi_debugfs_init, > > + .name = "ili9341", > > + .desc = "Ilitek ILI9341", > > + .date = "20180514", > > + .major = 1, > > + .minor = 0, > > +}; > > +static int ili9341_dbi_probe(struct spi_device *spi) > > +{ > > + struct mipi_dbi_dev *dbidev; > > + struct drm_device *drm; > > + struct mipi_dbi *dbi; > > + struct gpio_desc *dc; > > + struct device *dev = &spi->dev; > > + u32 rotation = 0; > > + int ret; > > + > > + dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver, > > + struct mipi_dbi_dev, drm); > > + if (IS_ERR(dbidev)) > > + return PTR_ERR(dbidev); > > + > > + dbi = &dbidev->dbi; > > + drm = &dbidev->drm; > > + > > + drm_mode_config_init(drm); > > + > > + dbi->reset = devm_gpiod_get_optional(dev, "reset", > > + GPIOD_OUT_HIGH); > > + if (IS_ERR(dbi->reset)) { > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); > > + return PTR_ERR(dbi->reset); > > + } > > + > > + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); > > + if (IS_ERR(dc)) { > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); > > + return PTR_ERR(dc); > > + } > > + > > + dbidev->regulator = devm_regulator_get_optional(dev, "vcc"); > > + if (IS_ERR(dbidev->regulator)) > > + dev_err(dev, "get optional vcc failed\n"); > > + > > + dbidev->backlight = devm_of_find_backlight(dev); > > + if (IS_ERR(dbidev->backlight)) > > + return PTR_ERR(dbidev->backlight); > > + > > + device_property_read_u32(dev, "rotation", &rotation); > > + > > + ret = mipi_dbi_spi_init(spi, dbi, dc); > > + if (ret) > > + return ret; > > + > > + ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs, > > + &ili9341_dbi_mode, rotation); > > + if (ret) > > + return ret; > > + > > + drm_mode_config_reset(drm); > > + > > + ret = drm_dev_register(drm, 0); > > + if (ret) > > + return ret; > > + > > + spi_set_drvdata(spi, drm); > > + > > + drm_fbdev_generic_setup(drm, 0); > > + > > + return 0; > > +} > > +static int ili9341_probe(struct spi_device *spi) > > +{ > > + const struct spi_device_id *id = spi_get_device_id(spi); > > + > > + if (!strcmp(id->name, "sf-tc240t-9370-t")) > > + return ili9341_dpi_probe(spi); > > + else if (!strcmp(id->name, "yx240qv29")) > > + return ili9341_dbi_probe(spi); > > + > > + return -1; > > +} > > + > > +static int ili9341_remove(struct spi_device *spi) > > +{ > > + const struct spi_device_id *id = spi_get_device_id(spi); > > + struct ili9341 *ili = spi_get_drvdata(spi); > > + struct drm_device *drm = spi_get_drvdata(spi); > > + > > + if (!strcmp(id->name, "sf-tc240t-9370-t")) { > > + ili9341_dpi_power_off(ili); > > + drm_panel_remove(&ili->panel); > > + } else if (!strcmp(id->name, "yx240qv29")) { > > + drm_dev_unplug(drm); > > + drm_atomic_helper_shutdown(drm); > > + } > > + return 0; > > +} > > + > > +static void ili9341_shutdown(struct spi_device *spi) > > +{ > > + const struct spi_device_id *id = spi_get_device_id(spi); > > + > > + if (!strcmp(id->name, "yx240qv29")) > > + drm_atomic_helper_shutdown(spi_get_drvdata(spi)); > > +} > > + > > +static const struct of_device_id ili9341_of_match[] = { > > + { > > + .compatible = "st,sf-tc240t-9370-t", > > + .data = &ili9341_stm32f429_disco_data, > > + }, > > + { > > + /* porting from tiny/ili9341.c > > + * for original mipi dbi compitable > > + */ > > + .compatible = "adafruit,yx240qv29", > > + .data = NULL, > > + }, > > +}; > > +MODULE_DEVICE_TABLE(of, ili9341_of_match); > > + > > +static const struct spi_device_id ili9341_id[] = { > > + { "yx240qv29", 0 }, > > + { "sf-tc240t-9370-t", 0 }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(spi, ili9341_id); > > + > > +static struct spi_driver ili9341_driver = { > > + .probe = ili9341_probe, > > + .remove = ili9341_remove, > > + .shutdown = ili9341_shutdown, > > + .id_table = ili9341_id, > > + .driver = { > > + .name = "panel-ilitek-ili9341", > > + .of_match_table = ili9341_of_match, > > + }, > > +}; > > +module_spi_driver(ili9341_driver); > > + > > +MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>"); > > +MODULE_DESCRIPTION("ILI9341 LCD panel driver"); > > +MODULE_LICENSE("GPL v2"); > >
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 4894913936e9..e4babba17864 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -123,6 +123,18 @@ config DRM_PANEL_ILITEK_IL9322 Say Y here if you want to enable support for Ilitek IL9322 QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. +config DRM_PANEL_ILITEK_ILI9341 + tristate "Ilitek ILI9341 240x320 QVGA panels" + depends on OF && SPI + depends on DRM_KMS_HELPER + depends on DRM_KMS_CMA_HELPER + depends on BACKLIGHT_CLASS_DEVICE + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for Ilitek IL9341 + QVGA (240x320) RGB panels. support serial & parallel rgb + interface. + config DRM_PANEL_ILITEK_ILI9881C tristate "Ilitek ILI9881C-based panels" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index cae4d976c069..0ecde184665d 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c new file mode 100644 index 000000000000..f84983cbb250 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c @@ -0,0 +1,1285 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Ilitek ILI9341 TFT LCD drm_panel driver. + * + * This panel can be configured to support: + * - 16-bit parallel RGB interface + * - 18-bit parallel RGB interface + * - 4-line serial spi interface + * + * Copyright (C) 2020 Dillon Min <dillon.minfei@gmail.com> + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c + */ + +#include <linux/bitops.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> +#include <linux/delay.h> +#include <video/mipi_display.h> +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_fb_helper.h> +#include <drm/drm_gem_atomic_helper.h> +#include <drm/drm_atomic_helper.h> + +#include <drm/drm_drv.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ +#define ILI9341_DFC 0xb6 /* Display Function Control register */ +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ +#define ILI9341_POWERA 0xcb /* Power control A register */ +#define ILI9341_POWERB 0xcf /* Power control B register */ +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ +#define ILI9341_DTCB 0xea /* Driver timing control B */ +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ + +#define ILI9341_MADCTL_BGR BIT(3) +#define ILI9341_MADCTL_MV BIT(5) +#define ILI9341_MADCTL_MX BIT(6) +#define ILI9341_MADCTL_MY BIT(7) + + +#define ILI9341_POWER_B_LEN 3 +#define ILI9341_POWER_SEQ_LEN 4 +#define ILI9341_DTCA_LEN 3 +#define ILI9341_DTCB_LEN 2 +#define ILI9341_POWER_A_LEN 5 +#define ILI9341_DFC_1_LEN 2 +#define ILI9341_FRC_LEN 2 +#define ILI9341_VCOM_1_LEN 2 +#define ILI9341_DFC_2_LEN 4 +#define ILI9341_COLUMN_ADDR_LEN 4 +#define ILI9341_PAGE_ADDR_LEN 4 +#define ILI9341_INTERFACE_LEN 3 +#define ILI9341_PGAMMA_LEN 15 +#define ILI9341_NGAMMA_LEN 15 +#define ILI9341_CA_LEN 3 + +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6)|BIT(4)) +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6)|BIT(5)) +#define ILI9341_GAMMA_CURVE_1 BIT(0) +#define ILI9341_IF_WE_MODE BIT(0) +#define ILI9341_IF_BIG_ENDIAN 0x00 +#define ILI9341_IF_DM_RGB BIT(2) +#define ILI9341_IF_DM_INTERNAL 0x00 +#define ILI9341_IF_DM_VSYNC BIT(3) +#define ILI9341_IF_RM_RGB BIT(1) +#define ILI9341_IF_RIM_RGB 0x00 + +#define ILI9341_COLUMN_ADDR 0x00ef +#define ILI9341_PAGE_ADDR 0x013f + +#define ILI9341_RGB_EPL BIT(0) +#define ILI9341_RGB_DPL BIT(1) +#define ILI9341_RGB_HSPL BIT(2) +#define ILI9341_RGB_VSPL BIT(3) +#define ILI9341_RGB_DE_MODE BIT(6) +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) + +#define ILI9341_DBI_VCOMH_4P6V 0x23 +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 +#define ILI9341_DBI_PRC_NORMAL 0x20 +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 +#define ILI9341_DBI_FRC_DIVA 0x00 +#define ILI9341_DBI_FRC_RTNA 0x1b +#define ILI9341_DBI_EMS_GAS BIT(0) +#define ILI9341_DBI_EMS_DTS BIT(1) +#define ILI9341_DBI_EMS_GON BIT(2) +/** + * ili9341_command - ili9341 command with optional parameter(s) + * @ili: struct ili9341 + * @cmd: Command + * @seq...: Optional parameter(s) + * + * Send command to the controller. + * + * Returns: + * Zero on success, negative error code on failure. + */ +#define ili9341_command(ili, cmd, seq...) \ +({ \ + u8 d[] = { seq }; \ + _ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \ +}) + +/** + * struct ili9341_config - the system specific ILI9341 configuration + * @max_spi_speed: 10000000 + */ +struct ili9341_config { + u32 max_spi_speed; + /** @mode: the drm display mode */ + const struct drm_display_mode mode; + /** @ca: TODO: need comments for this register */ + u8 ca[ILI9341_CA_LEN]; + /** @power_b: TODO: need comments for this register */ + u8 power_b[ILI9341_POWER_B_LEN]; + /** @power_seq: TODO: need comments for this register */ + u8 power_seq[ILI9341_POWER_SEQ_LEN]; + /** @dtca: TODO: need comments for this register */ + u8 dtca[ILI9341_DTCA_LEN]; + /** @dtcb: TODO: need comments for this register */ + u8 dtcb[ILI9341_DTCB_LEN]; + /** @power_a: TODO: need comments for this register */ + u8 power_a[ILI9341_POWER_A_LEN]; + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ + /* + * Formula to calculate frame frequency: + * Frame Rate=fosc/(Clocks per line x Division ratio x + * (Lines+VBP+VFP)) + * + * Sets the division ratio for internal clocks of Normal mode at MCU + * interface. + * + * fosc : internal oscillator frequency + * Clocks per line : RTNA setting + * Division ratio : DIVA setting + * Lines : total driving line number + * VBP : back porch line number + * VFP : front porch line number + * + * RTNA [4:0] Frame Rate (Hz) RTNA [4:0] Frame Rate (Hz) + * 1 0 0 0 0 119 1 1 0 0 0 79 + * 1 0 0 0 1 112 1 1 0 0 1 76 + * 1 0 0 1 0 106 1 1 0 1 0 73 + * 1 0 0 1 1 100 1 1 0 1 1 70(default) + * 1 0 1 0 0 95 1 1 1 0 0 68 + * 1 0 1 0 1 90 1 1 1 0 1 65 + * 1 0 1 1 0 86 1 1 1 0 1 63 + * 1 0 1 1 1 83 1 1 1 1 1 61 + * + * DIVA [1:0] : division ratio for internal clocks when Normal mode. + * + * DIVA [1:0] Division Ratio + * 0 0 fosc + * 0 1 fosc / 2 + * 1 0 fosc / 4 + * 1 1 fosc / 8 + * + */ + u8 frc[ILI9341_FRC_LEN]; + /** @prc: TODO: need comments for this register */ + u8 prc; + /** @dfc_1: B6h DISCTRL (Display Function Control) */ + /* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX + * Command 0 1 M XX 1 0 1 1 0 1 1 0 B6h + * 1st Parameter 1 1 M XX 0 0 0 0 PTG[1:0] PT[1:0] 0A + * 2nd Parameter 1 1 M XX REV GS SS SM ISC[3:0] 82 + * 3rd Parameter 1 1 M XX 0 0 NL[5:0] 27 + * 4th Parameter 1 1 M XX 0 0 PCDIV[5:0] XX + * + * PTG [1:0]: Set the scan mode in non-display area. + * PTG1 | PTG0 | Gate outputs in | Source outputs in | VCOM output + * non-display area | non-display area | + * 1 0 Interval scan Set with the PT[2:0] bits + * + * PT [1:0]: Determine source/VCOM output in a non-display area in the + * partial display mode. + * 1 0 AGND AGND AGND AGND + * + * REV: Select whether the liquid crystal type is normally white type + * or normally black type. + * REV Liquid crystal type + * 0 Normally black + * 1 Normally white + * + * SS: Select the shift direction of outputs from the source driver. + * SS Source Output Scan Direction + * 0 S1 -> S720 + * 1 S720 -> S1 + * + * GS: Sets the direction of scan by the gate driver in the range + * determined by SCN [4:0] and NL [4:0]. The scan direction + * determined by GS = 0 can be reversed by setting GS = 1. + * + * GS Gate Output Scan Direction + * 0 G1 -> G320 + * 1 G320 -> G1 + */ + u8 dfc_1[ILI9341_DFC_1_LEN]; + /** @power_1: Power Control 1 (C0h) */ + /* VRH [5:0]: Set the GVDD level, which is a reference level for the + * VCOM level and the grayscale voltage level. + * + * VRH[5:0] GVDD VRH[5:0] GVDD + * 0 0 0 0 0 0 Setting prohibited 1 0 0 0 0 0 4.45 V + * 0 0 0 0 0 1 Setting prohibited 1 0 0 0 0 1 4.50 V + * 0 0 0 0 1 0 Setting prohibited 1 0 0 0 1 0 4.55 V + * 0 0 0 0 1 1 3.00 V 1 0 0 0 1 1 4.60 V + * 0 0 0 1 0 0 3.05 V 1 0 0 1 0 0 4.65 V + * 0 0 0 1 0 1 3.10 V 1 0 0 1 0 1 4.70 V + * 0 0 0 1 1 0 3.15 V 1 0 0 1 1 0 4.75 V + * 0 0 0 1 1 1 3.20 V 1 0 0 1 1 1 4.80 V + * 0 0 1 0 0 0 3.25 V 1 0 1 0 0 0 4.85 V + * 0 0 1 0 0 1 3.30 V 1 0 1 0 0 1 4.90 V + * 0 0 1 0 1 0 3.35 V 1 0 1 0 1 0 4.95 V + * 0 0 1 0 1 1 3.40 V 1 0 1 0 1 1 5.00 V + * 0 0 1 1 0 0 3.45 V 1 0 1 1 0 0 5.05 V + * 0 0 1 1 0 1 3.50 V 1 0 1 1 0 1 5.10 V + * 0 0 1 1 1 0 3.55 V 1 0 1 1 1 0 5.15 V + * 0 0 1 1 1 1 3.60 V 1 0 1 1 1 1 5.20 V + * 0 1 0 0 0 0 3.65 V 1 1 0 0 0 0 5.25 V + * 0 1 0 0 0 1 3.70 V 1 1 0 0 0 1 5.30 V + * 0 1 0 0 1 0 3.75 V 1 1 0 0 1 0 5.35 V + * 0 1 0 0 1 1 3.80 V 1 1 0 0 1 1 5.40 V + * 0 1 0 1 0 0 3.85 V 1 1 0 1 0 0 5.45 V + * 0 1 0 1 0 1 3.90 V 1 1 0 1 0 1 5.50 V + * 0 1 0 1 1 0 3.95 V 1 1 0 1 1 0 5.55 V + * 0 1 0 1 1 1 4.00 V 1 1 0 1 1 1 5.60 V + * 0 1 1 0 0 0 4.05 V 1 1 1 0 0 0 5.65 V + * 0 1 1 0 0 1 4.10 V 1 1 1 0 0 1 5.70 V + * 0 1 1 0 1 0 4.15 V 1 1 1 0 1 0 5.75 V + * 0 1 1 0 1 1 4.20 V 1 1 1 0 1 1 5.80 V + * 0 1 1 1 0 0 4.25 V 1 1 1 1 0 0 5.85 V + * 0 1 1 1 0 1 4.30 V 1 1 1 1 0 1 5.90 V + * 0 1 1 1 1 0 4.35 V 1 1 1 1 1 0 5.95 V + * 0 1 1 1 1 1 4.40 V 1 1 1 1 1 1 6.00 V + */ + u8 power_1; + /** @power_2: Power Control 2 (C1h) */ + /* + * BT [2:0]: Sets the factor used in the step-up circuits. + * Select the optimal step-up factor for the operating voltage. To + * reduce power consumption, set a smaller factor. + * + * BT[2:0] AVDD VGH VGL + * 0 0 0 VCI x 2 VCI x 7 VCI x 4 + * 0 0 1 VCI x 3 + * 0 1 0 VCI x 6 VCI x 4 + * 0 1 1 VCI x 3 + * + */ + u8 power_2; + /** @vcom_1: VCOM Control 1(C5h) */ + /* + * VMH [6:0] : Set the VCOMH voltage + * + * VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH + * 0000000 2.700 0100000 3.500 1000000 4.300 1100000 5.100 + * 0000001 2.725 0100001 3.525 1000001 4.325 1100001 5.125 + * 0000010 2.750 0100010 3.550 1000010 4.350 1100010 5.150 + * 0000011 2.775 0100011 3.575 1000011 4.375 1100011 5.175 + * 0000100 2.800 0100100 3.600 1000100 4.400 1100100 5.200 + * 0000101 2.825 0100101 3.625 1000101 4.425 1100101 5.225 + * 0000110 2.850 0100110 3.650 1000110 4.450 1100110 5.250 + * 0000111 2.875 0100111 3.675 1000111 4.475 1100111 5.275 + * 0001000 2.900 0101000 3.700 1001000 4.500 1101000 5.300 + * 0001001 2.925 0101001 3.725 1001001 4.525 1101001 5.325 + * 0001010 2.950 0101010 3.750 1001010 4.550 1101010 5.350 + * 0001011 2.975 0101011 3.775 1001011 4.575 1101011 5.375 + * 0001100 3.000 0101100 3.800 1001100 4.600 1101100 5.400 + * 0001101 3.025 0101101 3.825 1001101 4.625 1101101 5.425 + * 0001110 3.050 0101110 3.850 1001110 4.650 1101110 5.450 + * 0001111 3.075 0101111 3.875 1001111 4.675 1101111 5.475 + * 0010000 3.100 0110000 3.900 1010000 4.700 1110000 5.500 + * 0010001 3.125 0110001 3.925 1010001 4.725 1110001 5.525 + * 0010010 3.150 0110010 3.950 1010010 4.750 1110010 5.550 + * 0010011 3.175 0110011 3.975 1010011 4.775 1110011 5.575 + * 0010100 3.200 0110100 4.000 1010100 4.800 1110100 5.600 + * 0010101 3.225 0110101 4.025 1010101 4.825 1110101 5.625 + * 0010110 3.250 0110110 4.050 1010110 4.850 1110110 5.650 + * 0010111 3.275 0110111 4.075 1010111 4.875 1110111 5.675 + * 0011000 3.300 0111000 4.100 1011000 4.900 1111000 5.700 + * 0011001 3.325 0111001 4.125 1011001 4.925 1111001 5.725 + * 0011010 3.350 0111010 4.150 1011010 4.950 1111010 5.750 + * 0011011 3.375 0111011 4.175 1011011 4.975 1111011 5.775 + * 0011100 3.400 0111100 4.200 1011100 5.000 1111100 5.800 + * 0011101 3.425 0111101 4.225 1011101 5.025 1111101 5.825 + * 0011110 3.450 0111110 4.250 1011110 5.050 1111110 5.850 + * 0011111 3.475 0111111 4.275 1011111 5.075 1111111 5.875 + * + * VML[6:0] : Set the VCOML voltage + * + * VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML + * 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100 + * 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075 + * 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050 + * 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025 + * 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0 + * 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved + * 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved + * 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved + * 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved + * 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved + * 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved + * 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved + * 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved + * 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved + * 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved + * 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved + * 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved + * 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved + * 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved + * 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved + * 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved + * 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved + * 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved + * 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved + * 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved + * 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved + * 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved + * 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved + * 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved + * 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved + * 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved + * 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved + */ + u8 vcom_1[ILI9341_VCOM_1_LEN]; + /** @vcom_2: VCOM Control 2(C7h) */ + /* + * C7h VMCTRL1 (VCOM Control 1) + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX + * Command 0 1 M XX 1 1 0 0 0 1 1 1 C7h + * Parameter 1 1 M XX nVM VMF[6:0] C0 + * + * nVM: nVM equals to “0” after power on reset and VCOM offset + * equals to program MTP value. When nVM set to “1”, setting + * of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted. + * + * VMF [6:0]: Set the VCOM offset voltage. + */ + u8 vcom_2; + /** @address_mode: Memory Access Control (36h) */ + /* + * 36h MADCTL (Memory Access Control) + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX + * Command 0 1 M XX 0 0 1 1 0 1 1 0 36h + * Parameter 1 1 M XX MY MX MV ML BGR MH 0 0 00 + * + * This command defines read/write scanning direction of frame memory. + * This command makes no change on the other driver status. + * + * Bit Name Description + * MY Row Address Order + * MX Column Address Order + * MV Row / Column Exchange These 3 bits control MCU to memory + * write/read direction. + * ML Vertical Refresh Order LCD vertical refresh direction control. + * BGR RGB-BGR Order Color selector switch control + * (0=RGB color filter panel, 1=BGR + * color filter panel) + * MH Horizontal Refresh ORDER LCD horizontal refreshing + * direction control. + * + * Note: When BGR bit is changed, the new setting is active + * immediately without update the content in Frame Memory again. + * + */ + u8 address_mode; + /** @g3amma_en: TODO: need comments for this register */ + u8 g3amma_en; + /** @rgb_interface: RGB Interface Signal Control (B0h) */ + /* + * B0h IFMODE (Interface Mode Control) + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX + * Command 0 1 M XX 1 0 1 1 0 0 0 0 B0h + * Parameter 1 1 M XX ByPass_MODE RCM[1] RCM[0] 0 VSPL HSPL DPL EPL 40 + * + * Sets the operation status of the display interface. The setting + * becomes effective as soon as the command is received. + * EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low + * enable for RGB interface) + * + * DPL: DOTCLK polarity set (“0”= data fetched at the rising time, + * “1”= data fetched at the falling time) + * + * HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High + * level sync clock) + * + * VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High + * level sync clock) + * + * RCM [1:0]: RGB interface selection (refer to the RGB interface + * section). + * + * ByPass_MODE: Select display data path whether Memory or Direct to + * Shift register when RGB Interface is used. + * + * ByPass_MODE Display Data Path + * 0 Direct to Shift Register (default) + * 1 Memory + */ + u8 rgb_interface; + /** @dfc_2: refer to dfc_1 */ + u8 dfc_2[ILI9341_DFC_2_LEN]; + /** @column_addr: Column Address Set (2Ah) */ + /* This command is used to define area of frame memory where MCU can + * access. This command makes no change on the + * other driver status. The values of SC [15:0] and EC [15:0] are + * referred when RAMWR command comes. Each value + * represents one column line in the Frame Memory. + */ + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; + /** @page_addr: Page Address Set (2Bh) */ + /* This command is used to define area of frame memory where MCU can + * access. This command makes no change on the + * other driver status. The values of SP [15:0] and EP [15:0] are + * referred when RAMWR command comes. Each value + * represents one Page line in the Frame Memory. + */ + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; + /** @interface: Interface Control (F6h) */ + /* + * F6h IFCTL (16bits Data Format Selection) + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX + * Command 0 1 M XX 1 1 1 1 0 1 1 0 F6h + * 1stParameter 1 1 M XX MY MX MV + * _EOR _EOR _EOR 0 BGR_EOR 0 0 WE MODE 01 + * 2ndParameter 1 1 M XX 0 0 EPF[1] EPF[0] 0 0 MDT[1] MDT[0] 00 + * 3rdParameter 1 1 M XX 0 0 ENDIAN 0 DM[1] DM[0] RM RIM 00 + * + */ + u8 interface[ILI9341_INTERFACE_LEN]; + /** @pixel_format: This command sets the pixel format for the RGB image data used by */ + /* the interface. DPI [2:0] is the pixel format select of RGB + * interface and DBI [2:0] is the pixel format of MCU interface. If a + * particular interface, either RGB interface or MCU interface, is + * not used then the corresponding bits in the parameter are ignored. + * The pixel format is shown in the table below. + * + * DPI[2:0] RGB Interface Format DBI[2:0] MCU Interface Format + * 0 0 0 Reserved 0 0 0 Reserved + * 0 0 1 Reserved 0 0 1 Reserved + * 0 1 0 Reserved 0 1 0 Reserved + * 0 1 1 Reserved 0 1 1 Reserved + * 1 0 0 Reserved 1 0 0 Reserved + * 1 0 1 16 bits / pixel 1 0 1 16 bits / pixel + * 1 1 0 18 bits / pixel 1 1 0 18 bits / pixel + * 1 1 1 Reserved 1 1 1 Reserved + * + */ + u8 pixel_format; + /** @gamma_curve: This command is used to select the desired Gamma curve for the */ + /* current display. A maximum of 4 fixed gamma curves can + * be selected. The curve is selected by setting the appropriate bit + * in the parameter as described in the Table: + * + * GC [7:0] Curve Selected + * 01h Gamma curve 1 (G2.2) + * 02h --- + * 04h --- + * 08h --- + */ + u8 gamma_curve; + /** @pgamma: Positive Gamma Correction (E0h) */ + /* + * Set the gray scale voltage to adjust the gamma characteristics of + * the TFT panel. + */ + u8 pgamma[ILI9341_PGAMMA_LEN]; + /** @ngamma: Negative Gamma Correction (E1h) */ + /* + * Set the gray scale voltage to adjust the gamma characteristics of + * the TFT panel. + */ + u8 ngamma[ILI9341_NGAMMA_LEN]; +}; + +struct ili9341 { + struct device *dev; + const struct ili9341_config *conf; + struct drm_panel panel; + struct gpio_desc *reset_gpio; + struct gpio_desc *dc_gpio; + u32 max_spi_speed; + struct regulator *vcc; +}; + +/* + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller + */ +static const struct ili9341_config ili9341_stm32f429_disco_data = { + .max_spi_speed = 10000000, + .mode = { + .clock = 6100, + .hdisplay = 240, + .hsync_start = 240 + 10,/* hfp 10 */ + .hsync_end = 240 + 10 + 10,/* hsync 10 */ + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ + .vdisplay = 320, + .vsync_start = 320 + 4,/* vfp 4 */ + .vsync_end = 320 + 4 + 2,/* vsync 2 */ + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ + .flags = 0, + .width_mm = 65, + .height_mm = 50, + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, + }, + /* TODO: need comments for this register */ + .ca = {0xc3, 0x08, 0x50}, + /* TODO: need comments for this register */ + .power_b = {0x00, 0xc1, 0x30}, + /* TODO: need comments for this register */ + .power_seq = {0x64, 0x03, 0x12, 0x81}, + /* TODO: need comments for this register */ + .dtca = {0x85, 0x00, 0x78}, + /* TODO: need comments for this register */ + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, + /* TODO: need comments for this register */ + .prc = 0x20, + /* TODO: need comments for this register */ + .dtcb = {0x00, 0x00}, + /* 0x00 fosc, 0x1b 70hz */ + .frc = {0x00, 0x1b}, + /* 0x0a Interval scan, AGND AGND AGND AGND + * 0xa2 Normally white, G1 -> G320, S720 -> S1, + * Scan Cycle 5 frames,85ms + */ + .dfc_1 = {0x0a, 0xa2}, + /* 0x10 3.65v */ + .power_1 = 0x10, + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ + .power_2 = 0x10, + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ + .vcom_1 = {0x45, 0x15}, + /* 0x90 offset voltage, VMH-48, VML-48 */ + .vcom_2 = 0x90, + /* 0xc8 Row Address Order, Column Address Order + * BGR 1 + */ + .address_mode = 0xc8, + .g3amma_en = 0x00, + /* 0xc2 + * Display Data Path: Memory + * RGB: DE mode + * DOTCLK polarity set (data fetched at the falling time) + */ + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | + ILI9341_RGB_DE_MODE | + ILI9341_RGB_DPL, + /* + * 0x0a + * Gate outputs in non-display area: Interval scan + * Determine source/VCOM output in a non-display area in the partial + * display mode: AGND AGND AGND AGND + * + * 0xa7 + * Scan Cycle: 15 frames + * fFLM = 60Hz: 255ms + * Liquid crystal type: Normally white + * Gate Output Scan Direction: G1 -> G320 + * Source Output Scan Direction: S720 -> S1 + * + * 0x27 + * LCD Driver Line: 320 lines + * + * 0x04 + * PCDIV: 4 + */ + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, + /* column address: 240 */ + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, + ILI9341_COLUMN_ADDR & 0xff}, + /* page address: 320 */ + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, + ILI9341_PAGE_ADDR & 0xff}, + /* Memory write control: When the transfer number of data exceeds + * (EC-SC+1)*(EP-SP+1), the column and page number will be + * reset, and the exceeding data will be written into the following + * column and page. + * Display Operation Mode: RGB Interface Mode + * Interface for RAM Access: RGB interface + * 16- bit RGB interface (1 transfer/pixel) + */ + .interface = {ILI9341_IF_WE_MODE, 0x00, + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, + /* DPI: 16 bits / pixel */ + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, + /* Curve Selected: Gamma curve 1 (G2.2) */ + .gamma_curve = ILI9341_GAMMA_CURVE_1, + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, + 0x09, 0x4e, 0x78, 0x3c, 0x09, + 0x13, 0x05, 0x17, 0x11, 0x00}, + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, + 0x07, 0x31, 0x33, 0x42, 0x05, + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, +}; + +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) +{ + return container_of(panel, struct ili9341, panel); +} + +static int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz, + u8 bpw, const void *buf, size_t len) +{ + size_t max_chunk = spi_max_transfer_size(spi); + struct spi_transfer tr = { + .bits_per_word = bpw, + .speed_hz = speed_hz, + .len = len, + }; + struct spi_message m; + size_t chunk; + int ret; + + spi_message_init_with_transfers(&m, &tr, 1); + + while (len) { + chunk = min(len, max_chunk); + + tr.tx_buf = buf; + tr.len = chunk; + buf += chunk; + len -= chunk; + + ret = spi_sync(spi, &m); + if (ret) { + dev_err(&spi->dev, "spi_sync error: %d\n", ret); + return ret; + } + } + return 0; +} + +static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data, + size_t count) +{ + struct spi_device *spi = to_spi_device(ili->dev); + int ret = 0; + + gpiod_set_value_cansleep(ili->dc_gpio, 0); + + ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8, + (const void *)&cmd, 1); + if (ret || data == NULL || count == 0) { + return ret; + } + + gpiod_set_value_cansleep(ili->dc_gpio, 1); + + return ili9341_spi_transfer(spi, ili->max_spi_speed, 8, + data, count); +} + +static int ili9341_dpi_init(struct ili9341 *ili) +{ + int ret; + ret = _ili9341_command(ili, 0xca, + ili->conf->ca, + ILI9341_CA_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_POWERB, + ili->conf->power_b, + ILI9341_POWER_B_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_POWER_SEQ, + ili->conf->power_seq, + ILI9341_POWER_SEQ_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_DTCA, + ili->conf->dtca, + ILI9341_DTCA_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_POWERA, + ili->conf->power_a, + ILI9341_POWER_A_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_PRC, + &ili->conf->prc, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_DTCB, + ili->conf->dtcb, + ILI9341_DTCB_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_FRC, + ili->conf->frc, + ILI9341_FRC_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_DFC, + ili->conf->dfc_1, + ILI9341_DFC_1_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_POWER1, + &ili->conf->power_1, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_POWER2, + &ili->conf->power_2, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_VCOM1, + ili->conf->vcom_1, + ILI9341_VCOM_1_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_VCOM2, + &ili->conf->vcom_2, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE, + &ili->conf->address_mode, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_3GAMMA_EN, + &ili->conf->g3amma_en, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE, + &ili->conf->rgb_interface, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_DFC, + ili->conf->dfc_2, + ILI9341_DFC_2_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS, + ili->conf->column_addr, + ILI9341_COLUMN_ADDR_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS, + ili->conf->page_addr, + ILI9341_PAGE_ADDR_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_INTERFACE, + ili->conf->interface, + ILI9341_INTERFACE_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT, + &ili->conf->pixel_format, + 1); + if (ret) + return ret; + + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); + if (ret) + return ret; + + msleep(200); + ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE, + &ili->conf->gamma_curve, + 1); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_PGAMMA, + ili->conf->pgamma, + ILI9341_PGAMMA_LEN); + if (ret) + return ret; + + ret = _ili9341_command(ili, ILI9341_NGAMMA, + ili->conf->ngamma, + ILI9341_NGAMMA_LEN); + if (ret) + return ret; + + ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE); + if (ret) + return ret; + + msleep(200); + ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); + if (ret) + return ret; + + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START); + if (ret) + return ret; + + dev_info(ili->dev, "initialized display rgb interface\n"); + + return 0; +} + +static int ili9341_dpi_power_on(struct ili9341 *ili) +{ + int ret = 0; + + /* Assert RESET */ + gpiod_set_value(ili->reset_gpio, 1); + + /* Enable power */ + if (!IS_ERR(ili->vcc)) { + ret = regulator_enable(ili->vcc); + if (ret < 0) { + dev_err(ili->dev, "unable to enable vcc\n"); + return ret; + } + } + msleep(20); + + /* De-assert RESET */ + gpiod_set_value(ili->reset_gpio, 0); + msleep(10); + + return 0; +} + +static int ili9341_dpi_power_off(struct ili9341 *ili) +{ + /* Assert RESET */ + gpiod_set_value(ili->reset_gpio, 1); + + /* Disable power */ + if (!IS_ERR(ili->vcc)) + return regulator_disable(ili->vcc); + + return 0; +} + +static int ili9341_dpi_disable(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF); + + return 0; +} + +static int ili9341_dpi_unprepare(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + return ili9341_dpi_power_off(ili); +} + +static int ili9341_dpi_prepare(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + int ret; + + ret = ili9341_dpi_power_on(ili); + if (ret < 0) + return ret; + + ret = ili9341_dpi_init(ili); + if (ret < 0) + ili9341_dpi_unprepare(panel); + + return ret; +} + +static int ili9341_dpi_enable(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON); + + return 0; +} + +static int ili9341_dpi_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + struct drm_device *drm = connector->dev; + struct drm_display_mode *mode; + struct drm_display_info *info; + + info = &connector->display_info; + info->width_mm = ili->conf->mode.width_mm; + info->height_mm = ili->conf->mode.height_mm; + + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; + else + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; + + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; + else + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; + + mode = drm_mode_duplicate(drm, &ili->conf->mode); + if (!mode) { + DRM_ERROR("bad mode or failed to add mode\n"); + return -EINVAL; + } + drm_mode_set_name(mode); + + /* Set up the polarity */ + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) + mode->flags |= DRM_MODE_FLAG_PHSYNC; + else + mode->flags |= DRM_MODE_FLAG_NHSYNC; + + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) + mode->flags |= DRM_MODE_FLAG_PVSYNC; + else + mode->flags |= DRM_MODE_FLAG_NVSYNC; + + drm_mode_probed_add(connector, mode); + + return 1; /* Number of modes */ +} + +static const struct drm_panel_funcs ili9341_dpi_funcs = { + .disable = ili9341_dpi_disable, + .unprepare = ili9341_dpi_unprepare, + .prepare = ili9341_dpi_prepare, + .enable = ili9341_dpi_enable, + .get_modes = ili9341_dpi_get_modes, +}; + +static int ili9341_dpi_probe(struct spi_device *spi) +{ + int ret; + struct device *dev = &spi->dev; + struct ili9341 *ili; + + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL); + if (!ili) + return -ENOMEM; + + spi_set_drvdata(spi, ili); + + ili->dev = dev; + /* + * Every new incarnation of this display must have a unique + * data entry for the system in this driver. + */ + ili->conf = of_device_get_match_data(dev); + if (!ili->conf) { + dev_err(dev, "missing device configuration\n"); + return -ENODEV; + } + + ili->vcc = devm_regulator_get_optional(dev, "vcc"); + if (IS_ERR(ili->vcc)) + dev_err(dev, "get optional vcc failed\n"); + + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(ili->reset_gpio)) { + dev_err(dev, "failed to get RESET GPIO\n"); + return PTR_ERR(ili->reset_gpio); + } + + ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW); + if (IS_ERR(ili->dc_gpio)) { + dev_err(dev, "failed to get DC GPIO\n"); + return PTR_ERR(ili->dc_gpio); + } + + spi->bits_per_word = 8; + ret = spi_setup(spi); + if (ret < 0) { + dev_err(dev, "spi setup failed.\n"); + return ret; + } + + ili->max_spi_speed = ili->conf->max_spi_speed; + + drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs, + DRM_MODE_CONNECTOR_DPI); + + drm_panel_add(&ili->panel); + + return 0; +} + + + +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, + struct drm_crtc_state *crtc_state, + struct drm_plane_state *plane_state) +{ + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); + struct mipi_dbi *dbi = &dbidev->dbi; + u8 addr_mode; + int ret, idx; + + if (!drm_dev_enter(pipe->crtc.dev, &idx)) + return; + + DRM_DEBUG_KMS("\n"); + + ret = mipi_dbi_poweron_conditional_reset(dbidev); + if (ret < 0) + goto out_exit; + if (ret == 1) + goto out_enable; + + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); + + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); + + /* Power Control */ + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); + /* VCOM */ + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, + ILI9341_DBI_VCOM_1_VML_1P5V); + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); + + /* Memory Access Control */ + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, + MIPI_DCS_PIXEL_FMT_16BIT); + + /* Frame Rate */ + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, + ILI9341_DBI_FRC_RTNA & 0x1f); + + /* Gamma */ + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); + mipi_dbi_command(dbi, ILI9341_PGAMMA, + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); + mipi_dbi_command(dbi, ILI9341_NGAMMA, + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); + + /* DDRAM */ + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | + ILI9341_DBI_EMS_DTS | + ILI9341_DBI_EMS_GON); + + /* Display */ + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); + msleep(100); + + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); + msleep(100); + +out_enable: + switch (dbidev->rotation) { + default: + addr_mode = ILI9341_MADCTL_MX; + break; + case 90: + addr_mode = ILI9341_MADCTL_MV; + break; + case 180: + addr_mode = ILI9341_MADCTL_MY; + break; + case 270: + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | + ILI9341_MADCTL_MX; + break; + } + addr_mode |= ILI9341_MADCTL_BGR; + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); + DRM_DEBUG_KMS("initialized display serial interface\n"); +out_exit: + drm_dev_exit(idx); +} + +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { + .enable = ili9341_dbi_enable, + .disable = mipi_dbi_pipe_disable, + .update = mipi_dbi_pipe_update, + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, +}; + +static const struct drm_display_mode ili9341_dbi_mode = { + DRM_SIMPLE_MODE(240, 320, 37, 49), +}; + +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); + +static struct drm_driver ili9341_dbi_driver = { + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, + .fops = &ili9341_dbi_fops, + DRM_GEM_CMA_DRIVER_OPS_VMAP, + .debugfs_init = mipi_dbi_debugfs_init, + .name = "ili9341", + .desc = "Ilitek ILI9341", + .date = "20180514", + .major = 1, + .minor = 0, +}; +static int ili9341_dbi_probe(struct spi_device *spi) +{ + struct mipi_dbi_dev *dbidev; + struct drm_device *drm; + struct mipi_dbi *dbi; + struct gpio_desc *dc; + struct device *dev = &spi->dev; + u32 rotation = 0; + int ret; + + dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver, + struct mipi_dbi_dev, drm); + if (IS_ERR(dbidev)) + return PTR_ERR(dbidev); + + dbi = &dbidev->dbi; + drm = &dbidev->drm; + + drm_mode_config_init(drm); + + dbi->reset = devm_gpiod_get_optional(dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(dbi->reset)) { + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); + return PTR_ERR(dbi->reset); + } + + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); + if (IS_ERR(dc)) { + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); + return PTR_ERR(dc); + } + + dbidev->regulator = devm_regulator_get_optional(dev, "vcc"); + if (IS_ERR(dbidev->regulator)) + dev_err(dev, "get optional vcc failed\n"); + + dbidev->backlight = devm_of_find_backlight(dev); + if (IS_ERR(dbidev->backlight)) + return PTR_ERR(dbidev->backlight); + + device_property_read_u32(dev, "rotation", &rotation); + + ret = mipi_dbi_spi_init(spi, dbi, dc); + if (ret) + return ret; + + ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs, + &ili9341_dbi_mode, rotation); + if (ret) + return ret; + + drm_mode_config_reset(drm); + + ret = drm_dev_register(drm, 0); + if (ret) + return ret; + + spi_set_drvdata(spi, drm); + + drm_fbdev_generic_setup(drm, 0); + + return 0; +} +static int ili9341_probe(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + + if (!strcmp(id->name, "sf-tc240t-9370-t")) + return ili9341_dpi_probe(spi); + else if (!strcmp(id->name, "yx240qv29")) + return ili9341_dbi_probe(spi); + + return -1; +} + +static int ili9341_remove(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + struct ili9341 *ili = spi_get_drvdata(spi); + struct drm_device *drm = spi_get_drvdata(spi); + + if (!strcmp(id->name, "sf-tc240t-9370-t")) { + ili9341_dpi_power_off(ili); + drm_panel_remove(&ili->panel); + } else if (!strcmp(id->name, "yx240qv29")) { + drm_dev_unplug(drm); + drm_atomic_helper_shutdown(drm); + } + return 0; +} + +static void ili9341_shutdown(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + + if (!strcmp(id->name, "yx240qv29")) + drm_atomic_helper_shutdown(spi_get_drvdata(spi)); +} + +static const struct of_device_id ili9341_of_match[] = { + { + .compatible = "st,sf-tc240t-9370-t", + .data = &ili9341_stm32f429_disco_data, + }, + { + /* porting from tiny/ili9341.c + * for original mipi dbi compitable + */ + .compatible = "adafruit,yx240qv29", + .data = NULL, + }, +}; +MODULE_DEVICE_TABLE(of, ili9341_of_match); + +static const struct spi_device_id ili9341_id[] = { + { "yx240qv29", 0 }, + { "sf-tc240t-9370-t", 0 }, + { } +}; +MODULE_DEVICE_TABLE(spi, ili9341_id); + +static struct spi_driver ili9341_driver = { + .probe = ili9341_probe, + .remove = ili9341_remove, + .shutdown = ili9341_shutdown, + .id_table = ili9341_id, + .driver = { + .name = "panel-ilitek-ili9341", + .of_match_table = ili9341_of_match, + }, +}; +module_spi_driver(ili9341_driver); + +MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>"); +MODULE_DESCRIPTION("ILI9341 LCD panel driver"); +MODULE_LICENSE("GPL v2");