| Message ID | 20210511020500.17269-22-ansuelsmth@gmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [RFC,net-next,v5,01/25] net: dsa: qca8k: change simple print to dev variant | expand |
On Tue, May 11, 2021 at 04:04:56AM +0200, Ansuel Smith wrote: > Document new way of declare mapping of internal PHY to port. > The new implementation directly declare the PHY connected to the port > by adding a node in the switch node. The driver detect this and register > an internal mdiobus using the mapping defined in the mdio node. > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > --- > .../devicetree/bindings/net/dsa/qca8k.txt | 39 +++++++++++++++++++ > 1 file changed, 39 insertions(+) > > diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt > index 1daf68e7ae19..3973a9d3e426 100644 > --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt > +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt > @@ -21,6 +21,10 @@ described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external > mdio-bus each subnode describing a port needs to have a valid phandle > referencing the internal PHY it is connected to. This is because there's no > N:N mapping of port and PHY id. > +To declare the internal mdio-bus configuration, declare a mdio node in the > +switch node and declare the phandle for the port referencing the internal > +PHY is connected to. In this config a internal mdio-bus is registred and registered Otherwise, Reviewed-by: Rob Herring <robh@kernel.org> > +the mdio MASTER is used as communication. > > Don't use mixed external and internal mdio-bus configurations, as this is > not supported by the hardware. > @@ -150,26 +154,61 @@ for the internal master mdio-bus configuration: > port@1 { > reg = <1>; > label = "lan1"; > + phy-mode = "internal"; > + phy-handle = <&phy_port1>; > }; > > port@2 { > reg = <2>; > label = "lan2"; > + phy-mode = "internal"; > + phy-handle = <&phy_port2>; > }; > > port@3 { > reg = <3>; > label = "lan3"; > + phy-mode = "internal"; > + phy-handle = <&phy_port3>; > }; > > port@4 { > reg = <4>; > label = "lan4"; > + phy-mode = "internal"; > + phy-handle = <&phy_port4>; > }; > > port@5 { > reg = <5>; > label = "wan"; > + phy-mode = "internal"; > + phy-handle = <&phy_port5>; > + }; > + }; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + phy_port1: phy@0 { > + reg = <0>; > + }; > + > + phy_port2: phy@1 { > + reg = <1>; > + }; > + > + phy_port3: phy@2 { > + reg = <2>; > + }; > + > + phy_port4: phy@3 { > + reg = <3>; > + }; > + > + phy_port5: phy@4 { > + reg = <4>; > }; > }; > }; > -- > 2.30.2 >
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index 1daf68e7ae19..3973a9d3e426 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -21,6 +21,10 @@ described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external mdio-bus each subnode describing a port needs to have a valid phandle referencing the internal PHY it is connected to. This is because there's no N:N mapping of port and PHY id. +To declare the internal mdio-bus configuration, declare a mdio node in the +switch node and declare the phandle for the port referencing the internal +PHY is connected to. In this config a internal mdio-bus is registred and +the mdio MASTER is used as communication. Don't use mixed external and internal mdio-bus configurations, as this is not supported by the hardware. @@ -150,26 +154,61 @@ for the internal master mdio-bus configuration: port@1 { reg = <1>; label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy_port1>; }; port@2 { reg = <2>; label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy_port2>; }; port@3 { reg = <3>; label = "lan3"; + phy-mode = "internal"; + phy-handle = <&phy_port3>; }; port@4 { reg = <4>; label = "lan4"; + phy-mode = "internal"; + phy-handle = <&phy_port4>; }; port@5 { reg = <5>; label = "wan"; + phy-mode = "internal"; + phy-handle = <&phy_port5>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; }; }; };
Document new way of declare mapping of internal PHY to port. The new implementation directly declare the PHY connected to the port by adding a node in the switch node. The driver detect this and register an internal mdiobus using the mapping defined in the mdio node. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- .../devicetree/bindings/net/dsa/qca8k.txt | 39 +++++++++++++++++++ 1 file changed, 39 insertions(+)