@@ -1,4 +1,4 @@
-===========
+===========
EHCI driver
===========
@@ -1,4 +1,4 @@
-===============================
+===============================
Linux USB Printer Gadget Driver
===============================
@@ -40,7 +40,7 @@ Module parameters
This parameter lists paths to files or block devices used for
backing storage for each logical unit. There may be at most
FSG_MAX_LUNS (8) LUNs set. If more files are specified, they will
- be silently ignored. See also “luns” parameter.
+ be silently ignored. See also "luns" parameter.
*BEWARE* that if a file is used as a backing storage, it may not
be modified by any other process. This is because the host
@@ -56,18 +56,18 @@ Module parameters
- removable=b[,b...]
This parameter specifies whether each logical unit should be
- removable. “b” here is either “y”, “Y” or “1” for true or “n”,
- “N” or “0” for false.
+ removable. "b" here is either "y", "Y" or "1" for true or "n",
+ "N" or "0" for false.
If this option is set for a logical unit, gadget will accept an
- “eject” SCSI request (Start/Stop Unit). When it is sent, the
+ "eject" SCSI request (Start/Stop Unit). When it is sent, the
backing file will be closed to simulate ejection and the logical
unit will not be mountable by the host until a new backing file is
- specified by userspace on the device (see “sysfs entries”
+ specified by userspace on the device (see "sysfs entries"
section).
If a logical unit is not removable (the default), a backing file
- must be specified for it with the “file” parameter as the module
+ must be specified for it with the "file" parameter as the module
is loaded. The same applies if the module is built in, no
exceptions.
@@ -76,13 +76,13 @@ Module parameters
and because it seems like a saner default after all. Thus to
maintain compatibility with older kernels, it's best to specify
the default values. Also, if one relied on old default, explicit
- “n” needs to be specified now.
+ "n" needs to be specified now.
- Note that “removable” means the logical unit's media can be
+ Note that "removable" means the logical unit's media can be
ejected or removed (as is true for a CD-ROM drive or a card
reader). It does *not* mean that the entire gadget can be
unplugged from the host; the proper term for that is
- “hot-unpluggable”.
+ "hot-unpluggable".
- cdrom=b[,b...]
@@ -107,7 +107,7 @@ Module parameters
This parameter specifies whether FUA flag should be ignored in SCSI
Write10 and Write12 commands sent to given logical units.
- MS Windows mounts removable storage in “Removal optimised mode” by
+ MS Windows mounts removable storage in "Removal optimised mode" by
default. All the writes to the media are synchronous, which is
achieved by setting the FUA (Force Unit Access) bit in SCSI
Write(10,12) commands. This forces each write to wait until the
@@ -127,11 +127,11 @@ Module parameters
capped.
If this parameter is provided, and the number of files specified
- in “file” argument is greater then the value of “luns”, all excess
+ in "file" argument is greater then the value of "luns", all excess
files will be ignored.
If this parameter is not present, the number of logical units will
- be deduced from the number of files specified in the “file”
+ be deduced from the number of files specified in the "file"
parameter. If the file parameter is missing as well, one is
assumed.
@@ -217,18 +217,18 @@ Relation to file storage gadget
All users need to transition to the Mass Storage Gadget. The two
gadgets behave mostly the same from the outside except:
- 1. In FSG the “removable” and “cdrom” module parameters set the flag
+ 1. In FSG the "removable" and "cdrom" module parameters set the flag
for all logical units whereas in MSG they accept a list of y/n
values for each logical unit. If one uses only a single logical
unit this does not matter, but if there are more, the y/n value
needs to be repeated for each logical unit.
- 2. FSG's “serial”, “vendor”, “product” and “release” module
+ 2. FSG's "serial", "vendor", "product" and "release" module
parameters are handled in MSG by the composite layer's parameters
- named respectively: “iSerialnumber”, “idVendor”, “idProduct” and
- “bcdDevice”.
+ named respectively: "iSerialnumber", "idVendor", "idProduct" and
+ "bcdDevice".
- 3. MSG does not support FSG's test mode, thus “transport”,
- “protocol” and “buflen” FSG's module parameters are not
+ 3. MSG does not support FSG's test mode, thus "transport",
+ "protocol" and "buflen" FSG's module parameters are not
supported. MSG always uses SCSI protocol with bulk only
transport mode and 16 KiB buffers.
@@ -1,4 +1,4 @@
-================
+================
mtouchusb driver
================
@@ -1,4 +1,4 @@
-==========
+==========
USB serial
==========
While UTF-8 characters can be used at the Linux documentation, the best is to use them only when ASCII doesn't offer a good replacement. So, replace the occurences of the following UTF-8 characters: - U+201c ('“'): LEFT DOUBLE QUOTATION MARK - U+201d ('”'): RIGHT DOUBLE QUOTATION MARK - U+feff (''): ZERO WIDTH NO-BREAK SPACE Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- Documentation/usb/ehci.rst | 2 +- Documentation/usb/gadget_printer.rst | 2 +- Documentation/usb/mass-storage.rst | 36 ++++++++++++++-------------- Documentation/usb/mtouchusb.rst | 2 +- Documentation/usb/usb-serial.rst | 2 +- 5 files changed, 22 insertions(+), 22 deletions(-)