@@ -1286,6 +1286,8 @@ static void dwc3_get_properties(struct dwc3 *dwc)
"snps,usb3_lpm_capable");
dwc->usb2_lpm_disable = device_property_read_bool(dev,
"snps,usb2-lpm-disable");
+ dwc->usb2_gadget_lpm_disable = device_property_read_bool(dev,
+ "snps,usb2-gadget-lpm-disable");
device_property_read_u8(dev, "snps,rx-thr-num-pkt-prd",
&rx_thr_num_pkt_prd);
device_property_read_u8(dev, "snps,rx-max-burst-prd",
@@ -1035,7 +1035,8 @@ struct dwc3_scratchpad_array {
* @dis_start_transfer_quirk: set if start_transfer failure SW workaround is
* not needed for DWC_usb31 version 1.70a-ea06 and below
* @usb3_lpm_capable: set if hadrware supports Link Power Management
- * @usb2_lpm_disable: set to disable usb2 lpm
+ * @usb2_lpm_disable: set to disable usb2 lpm for host
+ * @usb2_gadget_lpm_disable: set to disable usb2 lpm for gadget
* @disable_scramble_quirk: set if we enable the disable scramble quirk
* @u2exit_lfps_quirk: set if we enable u2exit lfps quirk
* @u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
@@ -1241,6 +1242,7 @@ struct dwc3 {
unsigned dis_start_transfer_quirk:1;
unsigned usb3_lpm_capable:1;
unsigned usb2_lpm_disable:1;
+ unsigned usb2_gadget_lpm_disable:1;
unsigned disable_scramble_quirk:1;
unsigned u2exit_lfps_quirk:1;
@@ -3484,6 +3484,7 @@ static void dwc3_gadget_conndone_interrupt(struct dwc3 *dwc)
/* Enable USB2 LPM Capability */
if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A) &&
+ !dwc->usb2_gadget_lpm_disable &&
(speed != DWC3_DSTS_SUPERSPEED) &&
(speed != DWC3_DSTS_SUPERSPEED_PLUS)) {
reg = dwc3_readl(dwc->regs, DWC3_DCFG);
@@ -3510,6 +3511,12 @@ static void dwc3_gadget_conndone_interrupt(struct dwc3 *dwc)
dwc3_gadget_dctl_write_safe(dwc, reg);
} else {
+ if (dwc->usb2_gadget_lpm_disable) {
+ reg = dwc3_readl(dwc->regs, DWC3_DCFG);
+ reg &= ~DWC3_DCFG_LPM_CAP;
+ dwc3_writel(dwc->regs, DWC3_DCFG, reg);
+ }
+
reg = dwc3_readl(dwc->regs, DWC3_DCTL);
reg &= ~DWC3_DCTL_HIRD_THRES_MASK;
dwc3_gadget_dctl_write_safe(dwc, reg);
@@ -3958,7 +3965,7 @@ int dwc3_gadget_init(struct dwc3 *dwc)
dwc->gadget->ssp_rate = USB_SSP_GEN_UNKNOWN;
dwc->gadget->sg_supported = true;
dwc->gadget->name = "dwc3-gadget";
- dwc->gadget->lpm_capable = true;
+ dwc->gadget->lpm_capable = !dwc->usb2_gadget_lpm_disable;
/*
* FIXME We might be setting max_speed to <SUPER, however versions
If the device doesn't support LPM, make sure to disable the LPM capability and don't advertise to the host that it supports it. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> --- Changes in v2: - Use a different DT property than usb2-lpm-disable (since it's host specific) drivers/usb/dwc3/core.c | 2 ++ drivers/usb/dwc3/core.h | 4 +++- drivers/usb/dwc3/gadget.c | 9 ++++++++- 3 files changed, 13 insertions(+), 2 deletions(-)