@@ -66,8 +66,7 @@ struct spi_imx_data;
struct spi_imx_devtype_data {
void (*intctrl)(struct spi_imx_data *, int);
int (*prepare_message)(struct spi_imx_data *, struct spi_message *);
- int (*prepare_transfer)(struct spi_imx_data *, struct spi_device *,
- struct spi_transfer *);
+ int (*prepare_transfer)(struct spi_imx_data *, struct spi_device *);
void (*trigger)(struct spi_imx_data *);
int (*rx_available)(struct spi_imx_data *);
void (*reset)(struct spi_imx_data *);
@@ -581,11 +580,10 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
}
static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
- struct spi_device *spi,
- struct spi_transfer *t)
+ struct spi_device *spi)
{
u32 ctrl = readl(spi_imx->base + MX51_ECSPI_CTRL);
- u32 clk = t->speed_hz, delay;
+ u32 clk, delay;
/* Clear BL field and set the right value */
ctrl &= ~MX51_ECSPI_CTRL_BL_MASK;
@@ -599,7 +597,7 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
/* set clock speed */
ctrl &= ~(0xf << MX51_ECSPI_CTRL_POSTDIV_OFFSET |
0xf << MX51_ECSPI_CTRL_PREDIV_OFFSET);
- ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
+ ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->spi_bus_clk, &clk);
spi_imx->spi_bus_clk = clk;
if (spi_imx->usedma)
@@ -711,13 +709,12 @@ static int mx31_prepare_message(struct spi_imx_data *spi_imx,
}
static int mx31_prepare_transfer(struct spi_imx_data *spi_imx,
- struct spi_device *spi,
- struct spi_transfer *t)
+ struct spi_device *spi)
{
unsigned int reg = MX31_CSPICTRL_ENABLE | MX31_CSPICTRL_MASTER;
unsigned int clk;
- reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, t->speed_hz, &clk) <<
+ reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, spi_imx->spi_bus_clk, &clk) <<
MX31_CSPICTRL_DR_SHIFT;
spi_imx->spi_bus_clk = clk;
@@ -816,14 +813,13 @@ static int mx21_prepare_message(struct spi_imx_data *spi_imx,
}
static int mx21_prepare_transfer(struct spi_imx_data *spi_imx,
- struct spi_device *spi,
- struct spi_transfer *t)
+ struct spi_device *spi)
{
unsigned int reg = MX21_CSPICTRL_ENABLE | MX21_CSPICTRL_MASTER;
unsigned int max = is_imx27_cspi(spi_imx) ? 16 : 18;
unsigned int clk;
- reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, t->speed_hz, max, &clk)
+ reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, spi_imx->spi_bus_clk, max, &clk)
<< MX21_CSPICTRL_DR_SHIFT;
spi_imx->spi_bus_clk = clk;
@@ -892,13 +888,12 @@ static int mx1_prepare_message(struct spi_imx_data *spi_imx,
}
static int mx1_prepare_transfer(struct spi_imx_data *spi_imx,
- struct spi_device *spi,
- struct spi_transfer *t)
+ struct spi_device *spi)
{
unsigned int reg = MX1_CSPICTRL_ENABLE | MX1_CSPICTRL_MASTER;
unsigned int clk;
- reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, t->speed_hz, &clk) <<
+ reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, spi_imx->spi_bus_clk, &clk) <<
MX1_CSPICTRL_DR_SHIFT;
spi_imx->spi_bus_clk = clk;
@@ -1177,6 +1172,16 @@ static int spi_imx_setupxfer(struct spi_device *spi,
if (!t)
return 0;
+ if (!t->speed_hz) {
+ if (!spi->max_speed_hz) {
+ dev_err(&spi->dev, "no speed_hz provided!\n");
+ return -EINVAL;
+ }
+ dev_dbg(&spi->dev, "using spi->max_speed_hz!\n");
+ spi_imx->spi_bus_clk = spi->max_speed_hz;
+ } else
+ spi_imx->spi_bus_clk = t->speed_hz;
+
spi_imx->bits_per_word = t->bits_per_word;
/*
@@ -1218,7 +1223,7 @@ static int spi_imx_setupxfer(struct spi_device *spi,
spi_imx->slave_burst = t->len;
}
- spi_imx->devtype_data->prepare_transfer(spi_imx, spi, t);
+ spi_imx->devtype_data->prepare_transfer(spi_imx, spi);
return 0;
}
When some drivers use spi to send data, spi_transfer->speed_hz is not assigned. If spidev->max_speed_hz is not assigned as well, it will cause an error in configuring the clock. Add a check for these two values before configuring the clock. An error will be returned when they are not assigned. Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> --- drivers/spi/spi-imx.c | 37 +++++++++++++++++++++---------------- 1 file changed, 21 insertions(+), 16 deletions(-)