@@ -10,8 +10,6 @@
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
-#include <linux/regmap.h>
-#include <linux/mfd/syscon.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/clk.h>
@@ -346,30 +344,8 @@ static int aspeed_vuart_handle_irq(struct uart_port *port)
return 1;
}
-static void aspeed_vuart_auto_configure_sirq_polarity(
- struct aspeed_vuart *vuart, struct device_node *syscon_np,
- u32 reg_offset, u32 reg_mask)
-{
- struct regmap *regmap;
- u32 value;
-
- regmap = syscon_node_to_regmap(syscon_np);
- if (IS_ERR(regmap)) {
- dev_warn(vuart->dev,
- "could not get regmap for aspeed,sirq-polarity-sense\n");
- return;
- }
- if (regmap_read(regmap, reg_offset, &value)) {
- dev_warn(vuart->dev, "could not read hw strap table\n");
- return;
- }
-
- aspeed_vuart_set_sirq_polarity(vuart, (value & reg_mask) == 0);
-}
-
static int aspeed_vuart_probe(struct platform_device *pdev)
{
- struct of_phandle_args sirq_polarity_sense_args;
struct uart_8250_port port;
struct aspeed_vuart *vuart;
struct device_node *np;
@@ -468,19 +444,8 @@ static int aspeed_vuart_probe(struct platform_device *pdev)
vuart->line = rc;
- rc = of_parse_phandle_with_fixed_args(
- np, "aspeed,sirq-polarity-sense", 2, 0,
- &sirq_polarity_sense_args);
- if (rc < 0) {
- dev_dbg(&pdev->dev,
- "aspeed,sirq-polarity-sense property not found\n");
- } else {
- aspeed_vuart_auto_configure_sirq_polarity(
- vuart, sirq_polarity_sense_args.np,
- sirq_polarity_sense_args.args[0],
- BIT(sirq_polarity_sense_args.args[1]));
- of_node_put(sirq_polarity_sense_args.np);
- }
+ if (of_property_read_bool(np, "aspeed,sirq-active-high"))
+ aspeed_vuart_set_sirq_polarity(vuart, 1);
aspeed_vuart_set_enabled(vuart, true);
aspeed_vuart_set_host_tx_discard(vuart, true);
@@ -254,7 +254,6 @@ config SERIAL_8250_ASPEED_VUART
tristate "Aspeed Virtual UART"
depends on SERIAL_8250
depends on OF
- depends on REGMAP && MFD_SYSCON
help
If you want to use the virtual UART (VUART) device on Aspeed
BMC platforms, enable this option. This enables the 16550A-
The initial implementation of this configuration conflated the SIRQ polarity setting with the syscon eSPI/LPC strapping; this patch disentangles them by reducing the DT config to a simple boolean. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> --- drivers/tty/serial/8250/8250_aspeed_vuart.c | 39 ++------------------- drivers/tty/serial/8250/Kconfig | 1 - 2 files changed, 2 insertions(+), 38 deletions(-)