| Message ID | 1615317483-23780-1-git-send-email-sbhanu@codeaurora.org |
|---|---|
| State | New |
| Headers | show |
| Series | [V1] arm64: dts: qcom: sc7280: Add nodes for eMMC and SD card | expand |
Hi! > + > +&sdhc_1 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_on>; > + pinctrl-1 = <&sdc1_off>; > + > + vmmc-supply = <&vreg_l7b_2p9>; > + vqmmc-supply = <&vreg_l19b_1p8>; > + Redundant newline, please remove > + > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > + mmc-hs400-enhanced-strobe; > + > + status = "disabled"; > + Redundant newline, please remove > + }; > + > + sdhc_2: sdhci@8804000 { > + compatible = "qcom,sdhci-msm-v5"; > + reg = <0 0x08804000 0 0x1000>; > + > + iommus = <&apps_smmu 0x100 0x0>; > + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC2_APPS_CLK>, > + <&gcc GCC_SDCC2_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "core", "iface", "xo"; > + > + bus-width = <4>; > + > + no-mmc; > + no-sdio; > + > + max-frequency = <202000000>; > + > + qcom,dll-config = <0x0007642c>; > + > + status = "disabled"; > + Redundant newline, please remove Konrad
On 3/10/2021 12:48 AM, Shaik Sajida Bhanu wrote: > Add nodes for eMMC and SD card on sc7280. > > Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org> > > --- > This change is depends on the below patch series: > https://lore.kernel.org/lkml/1613114930-1661-1-git-send-email-rnayak@codeaurora.org/ > https://lore.kernel.org/patchwork/project/lkml/list/?series=&submitter=28035&state=&q=&archive=&delegate= > --- > arch/arm64/boot/dts/qcom/sc7280-idp.dts | 26 +++++ > arch/arm64/boot/dts/qcom/sc7280.dtsi | 170 ++++++++++++++++++++++++++++++++ > 2 files changed, 196 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts > index ac79420..6abb2aa 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts > +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts > @@ -8,6 +8,7 @@ > /dts-v1/; > > #include "sc7280.dtsi" > +#include <dt-bindings/gpio/gpio.h> > > / { > model = "Qualcomm Technologies, Inc. SC7280 IDP platform"; > @@ -256,3 +257,28 @@ > bias-pull-up; > }; > }; > + > +&sdhc_1 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_on>; > + pinctrl-1 = <&sdc1_off>; > + > + vmmc-supply = <&vreg_l7b_2p9>; > + vqmmc-supply = <&vreg_l19b_1p8>; > + > +}; > + > +&sdhc_2 { > + status = "okay"; > + > + pinctrl-names = "default","sleep"; > + pinctrl-0 = <&sdc2_on>; > + pinctrl-1 = <&sdc2_off>; > + > + vmmc-supply = <&vreg_l9c_2p9>; > + vqmmc-supply = <&vreg_l6c_2p9>; > + > + cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; > +}; > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index 3b86052..91fb18a 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -18,6 +18,11 @@ > > chosen { }; > > + aliases { > + mmc1 = &sdhc_1; > + mmc2 = &sdhc_2; > + }; > + > clocks { > xo_board: xo-board { > compatible = "fixed-clock"; > @@ -315,6 +320,69 @@ > #power-domain-cells = <1>; > }; > > + sdhc_1: sdhci@7c4000 { > + compatible = "qcom,sdhci-msm-v5"; > + reg = <0 0x7c4000 0 0x1000>, > + <0 0x7c5000 0 0x1000>; > + reg-names = "hc", "cqhci"; > + > + iommus = <&apps_smmu 0xC0 0x0>; > + interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_APPS_CLK>, > + <&gcc GCC_SDCC1_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "core", "iface", "xo"; > + > + bus-width = <8>; > + non-removable; > + supports-cqe; > + no-sd; > + no-sdio; > + > + max-frequency = <192000000>; > + > + qcom,dll-config = <0x0007642c>; > + qcom,ddr-config = <0x80040868>; > + > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > + mmc-hs400-enhanced-strobe; > + > + status = "disabled"; > + > + }; > + > + sdhc_2: sdhci@8804000 { > + compatible = "qcom,sdhci-msm-v5"; > + reg = <0 0x08804000 0 0x1000>; > + > + iommus = <&apps_smmu 0x100 0x0>; > + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC2_APPS_CLK>, > + <&gcc GCC_SDCC2_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "core", "iface", "xo"; > + > + bus-width = <4>; > + > + no-mmc; > + no-sdio; > + > + max-frequency = <202000000>; > + > + qcom,dll-config = <0x0007642c>; > + > + status = "disabled"; > + > + }; > + > qupv3_id_0: geniqup@9c0000 { > compatible = "qcom,geni-se-qup"; > reg = <0 0x009c0000 0 0x2000>; > @@ -385,6 +453,108 @@ > pins = "gpio46", "gpio47"; > function = "qup13"; > }; > + > + sdc1_on: sdc1-on { > + pinconf-clk { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <16>; > + }; > + > + pinconf-cmd { > + pins = "sdc1_cmd"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + pinconf-data { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + pinconf-rclk { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + }; > + > + sdc1_off: sdc1-off { > + pinconf-clk { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + pinconf-cmd { > + pins = "sdc1_cmd"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + pinconf-data { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + pinconf-rclk { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + }; > + > + sdc2_on: sdc2-on { > + pinconf-clk { > + pins = "sdc2_clk"; > + bias-disable; > + drive-strength = <16>; > + }; > + > + pinconf-cmd { > + pins = "sdc2_cmd"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + pinconf-data { > + pins = "sdc2_data"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + pinconf-sd-cd { > + pins = "gpio91"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + }; > + > + sdc2_off: sdc2-off { > + pinconf-clk { > + pins = "sdc2_clk"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + pinconf-cmd { > + pins = "sdc2_cmd"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + pinconf-data { > + pins = "sdc2_data"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + pinconf-sd-cd { > + pins = "gpio91"; > + bias-disable; On few sc7180 based boards where external pull up is missing on cd-gpio, we had seen issues like un-intended interrupt on cd-gpio pin (since its getting toggled) during runtime PM cycle and resulting in unnecessary scheduling of SDcard scan (mmc_rescan). This issue is seen only when SDcard is not present. By enabling internal pull all the time (bais-pull-up), we can avoid such issue. > + drive-strength = <2>; > + }; > + }; > }; > > apps_smmu: iommu@15000000 {
On 2021-03-10 02:20, Konrad Dybcio wrote: > Hi! > > >> + >> +&sdhc_1 { >> + status = "okay"; >> + >> + pinctrl-names = "default", "sleep"; >> + pinctrl-0 = <&sdc1_on>; >> + pinctrl-1 = <&sdc1_off>; >> + >> + vmmc-supply = <&vreg_l7b_2p9>; >> + vqmmc-supply = <&vreg_l19b_1p8>; >> + > > Redundant newline, please remove > > >> + >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + mmc-hs400-1_8v; >> + mmc-hs400-enhanced-strobe; >> + >> + status = "disabled"; >> + > > Redundant newline, please remove > sure > >> + }; >> + >> + sdhc_2: sdhci@8804000 { >> + compatible = "qcom,sdhci-msm-v5"; >> + reg = <0 0x08804000 0 0x1000>; >> + >> + iommus = <&apps_smmu 0x100 0x0>; >> + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC2_APPS_CLK>, >> + <&gcc GCC_SDCC2_AHB_CLK>, >> + <&rpmhcc RPMH_CXO_CLK>; >> + clock-names = "core", "iface", "xo"; >> + >> + bus-width = <4>; >> + >> + no-mmc; >> + no-sdio; >> + >> + max-frequency = <202000000>; >> + >> + qcom,dll-config = <0x0007642c>; >> + >> + status = "disabled"; >> + > > Redundant newline, please remove > sure > > Konrad
On 2021-03-10 19:17, sbhanu@codeaurora.org wrote: > On 2021-03-10 01:32, Bjorn Andersson wrote: >> On Tue 09 Mar 13:18 CST 2021, Shaik Sajida Bhanu wrote: >> >>> Add nodes for eMMC and SD card on sc7280. >>> >>> Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org> >>> >>> --- >>> This change is depends on the below patch series: >>> https://lore.kernel.org/lkml/1613114930-1661-1-git-send-email-rnayak@codeaurora.org/ >>> https://lore.kernel.org/patchwork/project/lkml/list/?series=&submitter=28035&state=&q=&archive=&delegate= >>> --- >>> arch/arm64/boot/dts/qcom/sc7280-idp.dts | 26 +++++ >>> arch/arm64/boot/dts/qcom/sc7280.dtsi | 170 >>> ++++++++++++++++++++++++++++++++ >>> 2 files changed, 196 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts >>> b/arch/arm64/boot/dts/qcom/sc7280-idp.dts >>> index ac79420..6abb2aa 100644 >>> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts >>> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts >>> @@ -8,6 +8,7 @@ >>> /dts-v1/; >>> >>> #include "sc7280.dtsi" >>> +#include <dt-bindings/gpio/gpio.h> >>> >>> / { >>> model = "Qualcomm Technologies, Inc. SC7280 IDP platform"; >>> @@ -256,3 +257,28 @@ >>> bias-pull-up; >>> }; >>> }; >>> + >>> +&sdhc_1 { >>> + status = "okay"; >>> + >>> + pinctrl-names = "default", "sleep"; >>> + pinctrl-0 = <&sdc1_on>; >>> + pinctrl-1 = <&sdc1_off>; >>> + >>> + vmmc-supply = <&vreg_l7b_2p9>; >>> + vqmmc-supply = <&vreg_l19b_1p8>; >>> + >>> +}; >>> + >>> +&sdhc_2 { >>> + status = "okay"; >>> + >>> + pinctrl-names = "default","sleep"; >>> + pinctrl-0 = <&sdc2_on>; >>> + pinctrl-1 = <&sdc2_off>; >>> + >>> + vmmc-supply = <&vreg_l9c_2p9>; >>> + vqmmc-supply = <&vreg_l6c_2p9>; >>> + >>> + cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; >> >> Please add these nodes above the comment that says "PINCTRL - >> additions..." and please include the pinctrl state for gpio 91. >> > sure Hi >> "and please include the pinctrl state for gpio 91" sorry didn't get this >>> +}; >>> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi >>> b/arch/arm64/boot/dts/qcom/sc7280.dtsi >>> index 3b86052..91fb18a 100644 >>> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi >>> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi >>> @@ -18,6 +18,11 @@ >>> >>> chosen { }; >>> >>> + aliases { >>> + mmc1 = &sdhc_1; >>> + mmc2 = &sdhc_2; >>> + }; >>> + >>> clocks { >>> xo_board: xo-board { >>> compatible = "fixed-clock"; >>> @@ -315,6 +320,69 @@ >>> #power-domain-cells = <1>; >>> }; >>> >>> + sdhc_1: sdhci@7c4000 { >>> + compatible = "qcom,sdhci-msm-v5"; >>> + reg = <0 0x7c4000 0 0x1000>, >>> + <0 0x7c5000 0 0x1000>; >>> + reg-names = "hc", "cqhci"; >>> + >>> + iommus = <&apps_smmu 0xC0 0x0>; >>> + interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>, >>> + <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>; >>> + interrupt-names = "hc_irq", "pwr_irq"; >>> + >>> + clocks = <&gcc GCC_SDCC1_APPS_CLK>, >>> + <&gcc GCC_SDCC1_AHB_CLK>, >>> + <&rpmhcc RPMH_CXO_CLK>; >>> + clock-names = "core", "iface", "xo"; >>> + >>> + bus-width = <8>; >>> + non-removable; >>> + supports-cqe; >>> + no-sd; >>> + no-sdio; >>> + >>> + max-frequency = <192000000>; >>> + >>> + qcom,dll-config = <0x0007642c>; >>> + qcom,ddr-config = <0x80040868>; >>> + >>> + mmc-ddr-1_8v; >>> + mmc-hs200-1_8v; >>> + mmc-hs400-1_8v; >>> + mmc-hs400-enhanced-strobe; >>> + >>> + status = "disabled"; >>> + >>> + }; >>> + >>> + sdhc_2: sdhci@8804000 { >>> + compatible = "qcom,sdhci-msm-v5"; >>> + reg = <0 0x08804000 0 0x1000>; >>> + >>> + iommus = <&apps_smmu 0x100 0x0>; >>> + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, >>> + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; >>> + interrupt-names = "hc_irq", "pwr_irq"; >>> + >>> + clocks = <&gcc GCC_SDCC2_APPS_CLK>, >>> + <&gcc GCC_SDCC2_AHB_CLK>, >>> + <&rpmhcc RPMH_CXO_CLK>; >>> + clock-names = "core", "iface", "xo"; >>> + >>> + bus-width = <4>; >>> + >>> + no-mmc; >>> + no-sdio; >>> + >>> + max-frequency = <202000000>; >>> + >>> + qcom,dll-config = <0x0007642c>; >>> + >>> + status = "disabled"; >>> + >>> + }; >>> + >>> qupv3_id_0: geniqup@9c0000 { >>> compatible = "qcom,geni-se-qup"; >>> reg = <0 0x009c0000 0 0x2000>; >>> @@ -385,6 +453,108 @@ >>> pins = "gpio46", "gpio47"; >>> function = "qup13"; >>> }; >>> + >>> + sdc1_on: sdc1-on { >>> + pinconf-clk { >> >> The "pinconf-" prefix does not provide any value here. Can you please >> drop it? >> >> Regards, >> Bjorn > > sure will drop >> >>> + pins = "sdc1_clk"; >>> + bias-disable; >>> + drive-strength = <16>; >>> + }; >>> + >>> + pinconf-cmd { >>> + pins = "sdc1_cmd"; >>> + bias-pull-up; >>> + drive-strength = <10>; >>> + }; >>> + >>> + pinconf-data { >>> + pins = "sdc1_data"; >>> + bias-pull-up; >>> + drive-strength = <10>; >>> + }; >>> + >>> + pinconf-rclk { >>> + pins = "sdc1_rclk"; >>> + bias-pull-down; >>> + }; >>> + }; >>> + >>> + sdc1_off: sdc1-off { >>> + pinconf-clk { >>> + pins = "sdc1_clk"; >>> + bias-disable; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-cmd { >>> + pins = "sdc1_cmd"; >>> + bias-pull-up; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-data { >>> + pins = "sdc1_data"; >>> + bias-pull-up; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-rclk { >>> + pins = "sdc1_rclk"; >>> + bias-pull-down; >>> + }; >>> + }; >>> + >>> + sdc2_on: sdc2-on { >>> + pinconf-clk { >>> + pins = "sdc2_clk"; >>> + bias-disable; >>> + drive-strength = <16>; >>> + }; >>> + >>> + pinconf-cmd { >>> + pins = "sdc2_cmd"; >>> + bias-pull-up; >>> + drive-strength = <10>; >>> + }; >>> + >>> + pinconf-data { >>> + pins = "sdc2_data"; >>> + bias-pull-up; >>> + drive-strength = <10>; >>> + }; >>> + >>> + pinconf-sd-cd { >>> + pins = "gpio91"; >>> + bias-pull-up; >>> + drive-strength = <2>; >>> + }; >>> + }; >>> + >>> + sdc2_off: sdc2-off { >>> + pinconf-clk { >>> + pins = "sdc2_clk"; >>> + bias-disable; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-cmd { >>> + pins = "sdc2_cmd"; >>> + bias-pull-up; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-data { >>> + pins = "sdc2_data"; >>> + bias-pull-up; >>> + drive-strength = <2>; >>> + }; >>> + >>> + pinconf-sd-cd { >>> + pins = "gpio91"; >>> + bias-disable; >>> + drive-strength = <2>; >>> + }; >>> + }; >>> }; >>> >>> apps_smmu: iommu@15000000 { >>> -- >>> 2.7.4 >>>
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts index ac79420..6abb2aa 100644 --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "sc7280.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Qualcomm Technologies, Inc. SC7280 IDP platform"; @@ -256,3 +257,28 @@ bias-pull-up; }; }; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + + vmmc-supply = <&vreg_l7b_2p9>; + vqmmc-supply = <&vreg_l19b_1p8>; + +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 3b86052..91fb18a 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -18,6 +18,11 @@ chosen { }; + aliases { + mmc1 = &sdhc_1; + mmc2 = &sdhc_2; + }; + clocks { xo_board: xo-board { compatible = "fixed-clock"; @@ -315,6 +320,69 @@ #power-domain-cells = <1>; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>, + <0 0x7c5000 0 0x1000>; + reg-names = "hc", "cqhci"; + + iommus = <&apps_smmu 0xC0 0x0>; + interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "core", "iface", "xo"; + + bus-width = <8>; + non-removable; + supports-cqe; + no-sd; + no-sdio; + + max-frequency = <192000000>; + + qcom,dll-config = <0x0007642c>; + qcom,ddr-config = <0x80040868>; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + + }; + + sdhc_2: sdhci@8804000 { + compatible = "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + + iommus = <&apps_smmu 0x100 0x0>; + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "core", "iface", "xo"; + + bus-width = <4>; + + no-mmc; + no-sdio; + + max-frequency = <202000000>; + + qcom,dll-config = <0x0007642c>; + + status = "disabled"; + + }; + qupv3_id_0: geniqup@9c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x009c0000 0 0x2000>; @@ -385,6 +453,108 @@ pins = "gpio46", "gpio47"; function = "qup13"; }; + + sdc1_on: sdc1-on { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-sd-cd { + pins = "gpio91"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-sd-cd { + pins = "gpio91"; + bias-disable; + drive-strength = <2>; + }; + }; }; apps_smmu: iommu@15000000 {
Add nodes for eMMC and SD card on sc7280. Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org> --- This change is depends on the below patch series: https://lore.kernel.org/lkml/1613114930-1661-1-git-send-email-rnayak@codeaurora.org/ https://lore.kernel.org/patchwork/project/lkml/list/?series=&submitter=28035&state=&q=&archive=&delegate= --- arch/arm64/boot/dts/qcom/sc7280-idp.dts | 26 +++++ arch/arm64/boot/dts/qcom/sc7280.dtsi | 170 ++++++++++++++++++++++++++++++++ 2 files changed, 196 insertions(+)