diff mbox series

[thermal:,thermal/next] thermal: ti-soc-thermal: Simplify polling with iopoll

Message ID 161368078166.20312.4958055839767865943.tip-bot2@tip-bot2
State New
Headers show
Series [thermal:,thermal/next] thermal: ti-soc-thermal: Simplify polling with iopoll | expand

Commit Message

thermal-bot for Julien Panis Feb. 18, 2021, 8:39 p.m. UTC 
The following commit has been merged into the thermal/next branch of thermal:

Commit-ID:     514cbabb01422d501d533a6495b924e4c22d4822
Gitweb:        https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git//514cbabb01422d501d533a6495b924e4c22d4822
Author:        Tony Lindgren <tony@atomide.com>
AuthorDate:    Fri, 05 Feb 2021 15:45:33 +02:00
Committer:     Daniel Lezcano <daniel.lezcano@linaro.org>
CommitterDate: Mon, 15 Feb 2021 21:19:23 +01:00

thermal: ti-soc-thermal: Simplify polling with iopoll

We can use iopoll for checking the EOCZ (end of conversion) bit. And with
this we now also want to handle the timeout errors properly.

For omap3, we need about 1.2ms for the single mode sampling to wait for
EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
is faster and we can use 1ms timeout.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-4-tony@atomide.com
---
 drivers/thermal/ti-soc-thermal/ti-bandgap.c | 30 +++++++++-----------
 1 file changed, 14 insertions(+), 16 deletions(-)
diff mbox series

Patch

diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
index 6e92551..8a3646e 100644
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -15,7 +15,6 @@ 
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/clk.h>
-#include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/err.h>
@@ -27,6 +26,7 @@ 
 #include <linux/of_platform.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/cpu_pm.h>
 #include <linux/device.h>
 #include <linux/pm_runtime.h>
@@ -604,7 +604,9 @@  static int
 ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 {
 	struct temp_sensor_registers *tsr = bgp->conf->sensors[id].registers;
-	u32 counter;
+	void __iomem *temp_sensor_ctrl = bgp->base + tsr->temp_sensor_ctrl;
+	int error;
+	u32 val;
 
 	/* Select continuous or single conversion mode */
 	if (TI_BANDGAP_HAS(bgp, MODE_CONFIG)) {
@@ -619,26 +621,22 @@  ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 		RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1);
 
 		/* Wait for EOCZ going up */
-		counter = 1000;
-		while (--counter) {
-			if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-			    tsr->bgap_eocz_mask)
-				break;
-			udelay(1);
-		}
+		error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
+						  val & tsr->bgap_eocz_mask,
+						  1, 1000);
+		if (error)
+			dev_warn(bgp->dev, "eocz timed out waiting high\n");
 
 		/* Clear Start of Conversion if available */
 		RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0);
 	}
 
 	/* Wait for EOCZ going down, always needed even if no bgap_soc_mask */
-	counter = 1000;
-	while (--counter) {
-		if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-		      tsr->bgap_eocz_mask))
-			break;
-		udelay(1);
-	}
+	error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
+					  !(val & tsr->bgap_eocz_mask),
+					  1, 1500);
+	if (error)
+		dev_warn(bgp->dev, "eocz timed out waiting low\n");
 
 	return 0;
 }