| Message ID | 20210201232402.906223-1-luiz.dentz@gmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [RFC,v2] Bluetooth: btintel: Check firmware version before download | expand |
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=425679
---Test result---
##############################
Test: CheckPatch - PASS
##############################
Test: CheckGitLint - PASS
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - PASS
Total: 416, Passed: 402 (96.6%), Failed: 0, Not Run: 14
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
Hi Luiz, > This checking the firmware build number, week and years matches and then > skip the download process. > > Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> > --- > drivers/bluetooth/btintel.c | 88 +++++++++++++++++++++++++++-------- > drivers/bluetooth/btintel.h | 5 +- > drivers/bluetooth/btusb.c | 22 +++++---- > drivers/bluetooth/hci_intel.c | 2 +- > 4 files changed, 84 insertions(+), 33 deletions(-) > > diff --git a/drivers/bluetooth/btintel.c b/drivers/bluetooth/btintel.c > index 88ce5f0ffc4b..bf7b910966c8 100644 > --- a/drivers/bluetooth/btintel.c > +++ b/drivers/bluetooth/btintel.c > @@ -24,6 +24,14 @@ > #define ECDSA_OFFSET 644 > #define ECDSA_HEADER_LEN 320 > > +#define CMD_WRITE_BOOT_PARAMS 0xfc0e > +struct cmd_write_boot_params { > + u32 boot_addr; > + u8 fw_build_num; > + u8 fw_build_ww; > + u8 fw_build_yy; > +} _packed; > + > int btintel_check_bdaddr(struct hci_dev *hdev) > { > struct hci_rp_read_bd_addr *bda; > @@ -841,7 +849,7 @@ static int btintel_sfi_ecdsa_header_secure_send(struct hci_dev *hdev, > > static int btintel_download_firmware_payload(struct hci_dev *hdev, > const struct firmware *fw, > - u32 *boot_param, size_t offset) > + size_t offset) > { > int err; > const u8 *fw_ptr; > @@ -854,20 +862,6 @@ static int btintel_download_firmware_payload(struct hci_dev *hdev, > while (fw_ptr - fw->data < fw->size) { > struct hci_command_hdr *cmd = (void *)(fw_ptr + frag_len); > > - /* Each SKU has a different reset parameter to use in the > - * HCI_Intel_Reset command and it is embedded in the firmware > - * data. So, instead of using static value per SKU, check > - * the firmware data and save it for later use. > - */ > - if (le16_to_cpu(cmd->opcode) == 0xfc0e) { > - /* The boot parameter is the first 32-bit value > - * and rest of 3 octets are reserved. > - */ > - *boot_param = get_unaligned_le32(fw_ptr + sizeof(*cmd)); > - > - bt_dev_dbg(hdev, "boot_param=0x%x", *boot_param); > - } > - > frag_len += sizeof(*cmd) + cmd->plen; > > /* The parameter length of the secure send command requires > @@ -896,28 +890,84 @@ static int btintel_download_firmware_payload(struct hci_dev *hdev, > return err; > } > > +static bool btintel_firmware_version(struct hci_dev *hdev, > + u8 num, u8 ww, u8 yy, > + const struct firmware *fw, > + u32 *boot_addr) > +{ > + const u8 *fw_ptr; > + u32 frag_len; > + > + fw_ptr = fw->data; > + frag_len = 0; > + > + while (fw_ptr - fw->data < fw->size) { > + struct hci_command_hdr *cmd = (void *)(fw_ptr + frag_len); > + > + /* Each SKU has a different reset parameter to use in the > + * HCI_Intel_Reset command and it is embedded in the firmware > + * data. So, instead of using static value per SKU, check > + * the firmware data and save it for later use. > + */ > + if (le16_to_cpu(cmd->opcode) == CMD_WRITE_BOOT_PARAMS) { > + struct cmd_write_boot_params *params; > + > + params = (void *)(fw_ptr + sizeof(*cmd)); > + > + bt_dev_dbg(hdev, "Boot Address: 0x%x\n" > + "Firmware Version: %u-%u.%u", > + le32_to_cpu(params->boot_addr), > + params->fw_build_num, params->fw_build_ww, > + params->fw_build_yy); use two bt_dev_dbg here please. > + > + if (num == params->fw_build_num && > + ww == params->fw_build_ww && > + yy == params->fw_build_yy) > + return true; > + else The else part is not really needed here. > + return false; > + } Maybe this is better /* comment goes here, true when x and false when y */ return (num == params_foo && ww = params_bar && yy = params_foobar); > + > + frag_len += sizeof(*cmd) + cmd->plen; > + } > + > + return false; > +} > + > int btintel_download_firmware(struct hci_dev *hdev, > + struct intel_version *ver, > const struct firmware *fw, > u32 *boot_param) > { > int err; > > + /* Skip download if firmware has the same version */ > + if (btintel_firmware_version(hdev, ver->fw_build_num, ver->fw_build_ww, > + ver->fw_build_yy, fw, boot_param)) > + return -EALREADY; > + > err = btintel_sfi_rsa_header_secure_send(hdev, fw); > if (err) > return err; > > - return btintel_download_firmware_payload(hdev, fw, boot_param, > - RSA_HEADER_LEN); > + return btintel_download_firmware_payload(hdev, fw, RSA_HEADER_LEN); > } > EXPORT_SYMBOL_GPL(btintel_download_firmware); > > int btintel_download_firmware_newgen(struct hci_dev *hdev, > + struct intel_version_tlv *ver, > const struct firmware *fw, u32 *boot_param, > u8 hw_variant, u8 sbe_type) > { > int err; > u32 css_header_ver; > > + /* Skip download if firmware has the same version */ > + if (btintel_firmware_version(hdev, ver->min_fw_build_nn, > + ver->min_fw_build_cw, ver->min_fw_build_yy, > + fw, boot_param)) > + return -EALREADY; > + > /* iBT hardware variants 0x0b, 0x0c, 0x11, 0x12, 0x13, 0x14 support > * only RSA secure boot engine. Hence, the corresponding sfi file will > * have RSA header of 644 bytes followed by Command Buffer. > @@ -947,7 +997,7 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, > if (err) > return err; > > - err = btintel_download_firmware_payload(hdev, fw, boot_param, RSA_HEADER_LEN); > + err = btintel_download_firmware_payload(hdev, fw, RSA_HEADER_LEN); > if (err) > return err; > } else if (hw_variant >= 0x17) { > @@ -968,7 +1018,6 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, > return err; > > err = btintel_download_firmware_payload(hdev, fw, > - boot_param, > RSA_HEADER_LEN + ECDSA_HEADER_LEN); > if (err) > return err; > @@ -978,7 +1027,6 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, > return err; > > err = btintel_download_firmware_payload(hdev, fw, > - boot_param, > RSA_HEADER_LEN + ECDSA_HEADER_LEN); > if (err) > return err; > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h > index 6511b091caf5..51f1f2c883b4 100644 > --- a/drivers/bluetooth/btintel.h > +++ b/drivers/bluetooth/btintel.h > @@ -163,9 +163,10 @@ struct regmap *btintel_regmap_init(struct hci_dev *hdev, u16 opcode_read, > int btintel_send_intel_reset(struct hci_dev *hdev, u32 boot_param); > int btintel_read_boot_params(struct hci_dev *hdev, > struct intel_boot_params *params); > -int btintel_download_firmware(struct hci_dev *dev, const struct firmware *fw, > - u32 *boot_param); > +int btintel_download_firmware(struct hci_dev *dev, struct intel_version *ver, > + const struct firmware *fw, u32 *boot_param); > int btintel_download_firmware_newgen(struct hci_dev *hdev, > + struct intel_version_tlv *ver, > const struct firmware *fw, > u32 *boot_param, u8 hw_variant, > u8 sbe_type); > diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c > index 4266c057746e..a06e86f52da3 100644 > --- a/drivers/bluetooth/btusb.c > +++ b/drivers/bluetooth/btusb.c > @@ -2612,14 +2612,15 @@ static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev, > set_bit(BTUSB_DOWNLOADING, &data->flags); > > /* Start firmware downloading and get boot parameter */ > - err = btintel_download_firmware_newgen(hdev, fw, boot_param, > + err = btintel_download_firmware_newgen(hdev, ver, fw, boot_param, > INTEL_HW_VARIANT(ver->cnvi_bt), > ver->sbe_type); > if (err < 0) { > - /* When FW download fails, send Intel Reset to retry > - * FW download. > - */ > - btintel_reset_to_bootloader(hdev); > + if (err != -EALREADY) > + /* When FW download fails, send Intel Reset to retry > + * FW download. > + */ > + btintel_reset_to_bootloader(hdev); Need another comment about the EALREADY case and here { } around it for readability. > goto done; > } > set_bit(BTUSB_FIRMWARE_LOADED, &data->flags); > @@ -2806,12 +2807,13 @@ static int btusb_intel_download_firmware(struct hci_dev *hdev, > set_bit(BTUSB_DOWNLOADING, &data->flags); > > /* Start firmware downloading and get boot parameter */ > - err = btintel_download_firmware(hdev, fw, boot_param); > + err = btintel_download_firmware(hdev, ver, fw, boot_param); > if (err < 0) { > - /* When FW download fails, send Intel Reset to retry > - * FW download. > - */ > - btintel_reset_to_bootloader(hdev); > + if (err != -EALREADY) > + /* When FW download fails, send Intel Reset to retry > + * FW download. > + */ > + btintel_reset_to_bootloader(hdev); See comment above. > goto done; > } > set_bit(BTUSB_FIRMWARE_LOADED, &data->flags); > diff --git a/drivers/bluetooth/hci_intel.c b/drivers/bluetooth/hci_intel.c > index b20a40fab83e..050fae33dab8 100644 > --- a/drivers/bluetooth/hci_intel.c > +++ b/drivers/bluetooth/hci_intel.c > @@ -735,7 +735,7 @@ static int intel_setup(struct hci_uart *hu) > set_bit(STATE_DOWNLOADING, &intel->flags); > > /* Start firmware downloading and get boot parameter */ > - err = btintel_download_firmware(hdev, fw, &boot_param); > + err = btintel_download_firmware(hdev, &ver, fw, &boot_param); > if (err < 0) > goto done; Regards Marcel
diff --git a/drivers/bluetooth/btintel.c b/drivers/bluetooth/btintel.c index 88ce5f0ffc4b..bf7b910966c8 100644 --- a/drivers/bluetooth/btintel.c +++ b/drivers/bluetooth/btintel.c @@ -24,6 +24,14 @@ #define ECDSA_OFFSET 644 #define ECDSA_HEADER_LEN 320 +#define CMD_WRITE_BOOT_PARAMS 0xfc0e +struct cmd_write_boot_params { + u32 boot_addr; + u8 fw_build_num; + u8 fw_build_ww; + u8 fw_build_yy; +} _packed; + int btintel_check_bdaddr(struct hci_dev *hdev) { struct hci_rp_read_bd_addr *bda; @@ -841,7 +849,7 @@ static int btintel_sfi_ecdsa_header_secure_send(struct hci_dev *hdev, static int btintel_download_firmware_payload(struct hci_dev *hdev, const struct firmware *fw, - u32 *boot_param, size_t offset) + size_t offset) { int err; const u8 *fw_ptr; @@ -854,20 +862,6 @@ static int btintel_download_firmware_payload(struct hci_dev *hdev, while (fw_ptr - fw->data < fw->size) { struct hci_command_hdr *cmd = (void *)(fw_ptr + frag_len); - /* Each SKU has a different reset parameter to use in the - * HCI_Intel_Reset command and it is embedded in the firmware - * data. So, instead of using static value per SKU, check - * the firmware data and save it for later use. - */ - if (le16_to_cpu(cmd->opcode) == 0xfc0e) { - /* The boot parameter is the first 32-bit value - * and rest of 3 octets are reserved. - */ - *boot_param = get_unaligned_le32(fw_ptr + sizeof(*cmd)); - - bt_dev_dbg(hdev, "boot_param=0x%x", *boot_param); - } - frag_len += sizeof(*cmd) + cmd->plen; /* The parameter length of the secure send command requires @@ -896,28 +890,84 @@ static int btintel_download_firmware_payload(struct hci_dev *hdev, return err; } +static bool btintel_firmware_version(struct hci_dev *hdev, + u8 num, u8 ww, u8 yy, + const struct firmware *fw, + u32 *boot_addr) +{ + const u8 *fw_ptr; + u32 frag_len; + + fw_ptr = fw->data; + frag_len = 0; + + while (fw_ptr - fw->data < fw->size) { + struct hci_command_hdr *cmd = (void *)(fw_ptr + frag_len); + + /* Each SKU has a different reset parameter to use in the + * HCI_Intel_Reset command and it is embedded in the firmware + * data. So, instead of using static value per SKU, check + * the firmware data and save it for later use. + */ + if (le16_to_cpu(cmd->opcode) == CMD_WRITE_BOOT_PARAMS) { + struct cmd_write_boot_params *params; + + params = (void *)(fw_ptr + sizeof(*cmd)); + + bt_dev_dbg(hdev, "Boot Address: 0x%x\n" + "Firmware Version: %u-%u.%u", + le32_to_cpu(params->boot_addr), + params->fw_build_num, params->fw_build_ww, + params->fw_build_yy); + + if (num == params->fw_build_num && + ww == params->fw_build_ww && + yy == params->fw_build_yy) + return true; + else + return false; + } + + frag_len += sizeof(*cmd) + cmd->plen; + } + + return false; +} + int btintel_download_firmware(struct hci_dev *hdev, + struct intel_version *ver, const struct firmware *fw, u32 *boot_param) { int err; + /* Skip download if firmware has the same version */ + if (btintel_firmware_version(hdev, ver->fw_build_num, ver->fw_build_ww, + ver->fw_build_yy, fw, boot_param)) + return -EALREADY; + err = btintel_sfi_rsa_header_secure_send(hdev, fw); if (err) return err; - return btintel_download_firmware_payload(hdev, fw, boot_param, - RSA_HEADER_LEN); + return btintel_download_firmware_payload(hdev, fw, RSA_HEADER_LEN); } EXPORT_SYMBOL_GPL(btintel_download_firmware); int btintel_download_firmware_newgen(struct hci_dev *hdev, + struct intel_version_tlv *ver, const struct firmware *fw, u32 *boot_param, u8 hw_variant, u8 sbe_type) { int err; u32 css_header_ver; + /* Skip download if firmware has the same version */ + if (btintel_firmware_version(hdev, ver->min_fw_build_nn, + ver->min_fw_build_cw, ver->min_fw_build_yy, + fw, boot_param)) + return -EALREADY; + /* iBT hardware variants 0x0b, 0x0c, 0x11, 0x12, 0x13, 0x14 support * only RSA secure boot engine. Hence, the corresponding sfi file will * have RSA header of 644 bytes followed by Command Buffer. @@ -947,7 +997,7 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, if (err) return err; - err = btintel_download_firmware_payload(hdev, fw, boot_param, RSA_HEADER_LEN); + err = btintel_download_firmware_payload(hdev, fw, RSA_HEADER_LEN); if (err) return err; } else if (hw_variant >= 0x17) { @@ -968,7 +1018,6 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, return err; err = btintel_download_firmware_payload(hdev, fw, - boot_param, RSA_HEADER_LEN + ECDSA_HEADER_LEN); if (err) return err; @@ -978,7 +1027,6 @@ int btintel_download_firmware_newgen(struct hci_dev *hdev, return err; err = btintel_download_firmware_payload(hdev, fw, - boot_param, RSA_HEADER_LEN + ECDSA_HEADER_LEN); if (err) return err; diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h index 6511b091caf5..51f1f2c883b4 100644 --- a/drivers/bluetooth/btintel.h +++ b/drivers/bluetooth/btintel.h @@ -163,9 +163,10 @@ struct regmap *btintel_regmap_init(struct hci_dev *hdev, u16 opcode_read, int btintel_send_intel_reset(struct hci_dev *hdev, u32 boot_param); int btintel_read_boot_params(struct hci_dev *hdev, struct intel_boot_params *params); -int btintel_download_firmware(struct hci_dev *dev, const struct firmware *fw, - u32 *boot_param); +int btintel_download_firmware(struct hci_dev *dev, struct intel_version *ver, + const struct firmware *fw, u32 *boot_param); int btintel_download_firmware_newgen(struct hci_dev *hdev, + struct intel_version_tlv *ver, const struct firmware *fw, u32 *boot_param, u8 hw_variant, u8 sbe_type); diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 4266c057746e..a06e86f52da3 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -2612,14 +2612,15 @@ static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev, set_bit(BTUSB_DOWNLOADING, &data->flags); /* Start firmware downloading and get boot parameter */ - err = btintel_download_firmware_newgen(hdev, fw, boot_param, + err = btintel_download_firmware_newgen(hdev, ver, fw, boot_param, INTEL_HW_VARIANT(ver->cnvi_bt), ver->sbe_type); if (err < 0) { - /* When FW download fails, send Intel Reset to retry - * FW download. - */ - btintel_reset_to_bootloader(hdev); + if (err != -EALREADY) + /* When FW download fails, send Intel Reset to retry + * FW download. + */ + btintel_reset_to_bootloader(hdev); goto done; } set_bit(BTUSB_FIRMWARE_LOADED, &data->flags); @@ -2806,12 +2807,13 @@ static int btusb_intel_download_firmware(struct hci_dev *hdev, set_bit(BTUSB_DOWNLOADING, &data->flags); /* Start firmware downloading and get boot parameter */ - err = btintel_download_firmware(hdev, fw, boot_param); + err = btintel_download_firmware(hdev, ver, fw, boot_param); if (err < 0) { - /* When FW download fails, send Intel Reset to retry - * FW download. - */ - btintel_reset_to_bootloader(hdev); + if (err != -EALREADY) + /* When FW download fails, send Intel Reset to retry + * FW download. + */ + btintel_reset_to_bootloader(hdev); goto done; } set_bit(BTUSB_FIRMWARE_LOADED, &data->flags); diff --git a/drivers/bluetooth/hci_intel.c b/drivers/bluetooth/hci_intel.c index b20a40fab83e..050fae33dab8 100644 --- a/drivers/bluetooth/hci_intel.c +++ b/drivers/bluetooth/hci_intel.c @@ -735,7 +735,7 @@ static int intel_setup(struct hci_uart *hu) set_bit(STATE_DOWNLOADING, &intel->flags); /* Start firmware downloading and get boot parameter */ - err = btintel_download_firmware(hdev, fw, &boot_param); + err = btintel_download_firmware(hdev, &ver, fw, &boot_param); if (err < 0) goto done;