@@ -7,7 +7,10 @@
* Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
*/
+#include <linux/acpi.h>
#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/machine.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/regmap.h>
@@ -15,11 +18,128 @@
#include <linux/slab.h>
#include <linux/spi/spi.h>
#include <linux/of.h>
+#include <uapi/linux/input-event-codes.h>
#include <linux/mfd/arizona/core.h>
#include "arizona.h"
+#ifdef CONFIG_ACPI
+const struct acpi_gpio_params reset_gpios = { 1, 0, false };
+const struct acpi_gpio_params ldoena_gpios = { 2, 0, false };
+
+static const struct acpi_gpio_mapping arizona_acpi_gpios[] = {
+ { "reset-gpios", &reset_gpios, 1, },
+ { "wlf,ldoena-gpios", &ldoena_gpios, 1 },
+ { }
+};
+
+/*
+ * The ACPI resources for the device only describe external GPIO-s. They do
+ * not provide mappings for the GPIO-s coming from the Arizona codec itself.
+ */
+static const struct gpiod_lookup arizona_soc_gpios[] = {
+ { "arizona", 2, "wlf,spkvdd-ena", 0, GPIO_ACTIVE_HIGH },
+ { "arizona", 4, "wlf,micd-pol", 0, GPIO_ACTIVE_LOW },
+};
+
+/*
+ * The AOSP 3.5 mm Headset: Accessory Specification gives the following values:
+ * Function A Play/Pause: 0 ohm
+ * Function D Voice assistant: 135 ohm
+ * Function B Volume Up 240 ohm
+ * Function C Volume Down 470 ohm
+ * Minimum Mic DC resistance 1000 ohm
+ * Minimum Ear speaker impedance 16 ohm
+ * Note the first max value below must be less then the min. speaker impedance,
+ * to allow CTIA/OMTP detection to work. The other max values are the closest
+ * value from extcon-arizona.c:arizona_micd_levels halfway 2 button resistances.
+ */
+static const struct arizona_micd_range arizona_micd_aosp_ranges[] = {
+ { .max = 11, .key = KEY_PLAYPAUSE },
+ { .max = 186, .key = KEY_VOICECOMMAND },
+ { .max = 348, .key = KEY_VOLUMEUP },
+ { .max = 752, .key = KEY_VOLUMEDOWN },
+};
+
+static void arizona_spi_acpi_remove_lookup(void *lookup)
+{
+ gpiod_remove_lookup_table(lookup);
+}
+
+static int arizona_spi_acpi_probe(struct arizona *arizona)
+{
+ struct gpiod_lookup_table *lookup;
+ acpi_status status;
+ int ret;
+
+ /* Add mappings for the 2 ACPI declared GPIOs used for reset and ldo-ena */
+ devm_acpi_dev_add_driver_gpios(arizona->dev, arizona_acpi_gpios);
+
+ /* Add lookups for the SoCs own GPIOs used for micdet-polarity and spkVDD-enable */
+ lookup = devm_kzalloc(arizona->dev,
+ struct_size(lookup, table, ARRAY_SIZE(arizona_soc_gpios) + 1),
+ GFP_KERNEL);
+ if (!lookup)
+ return -ENOMEM;
+
+ lookup->dev_id = dev_name(arizona->dev);
+ memcpy(lookup->table, arizona_soc_gpios, sizeof(arizona_soc_gpios));
+
+ gpiod_add_lookup_table(lookup);
+ ret = devm_add_action_or_reset(arizona->dev, arizona_spi_acpi_remove_lookup, lookup);
+ if (ret)
+ return ret;
+
+ /* Enable 32KHz clock from SoC to codec for jack-detect */
+ status = acpi_evaluate_object(ACPI_HANDLE(arizona->dev), "CLKE", NULL, NULL);
+ if (ACPI_FAILURE(status))
+ dev_warn(arizona->dev, "Failed to enable 32KHz clk ACPI error %d\n", status);
+
+ /*
+ * Some DSDTs wrongly declare the IRQ trigger-type as IRQF_TRIGGER_FALLING
+ * The IRQ line will stay low when a new IRQ event happens between reading
+ * the IRQ status flags and acknowledging them. When the IRQ line stays
+ * low like this the IRQ will never trigger again when its type is set
+ * to IRQF_TRIGGER_FALLING. Correct the IRQ trigger-type to fix this.
+ *
+ * Note theoretically it is possible that some boards are not capable
+ * of handling active low level interrupts. In that case setting the
+ * flag to IRQF_TRIGGER_FALLING would not be a bug (and we would need
+ * to work around this) but so far all known usages of IRQF_TRIGGER_FALLING
+ * are a bug in the board's DSDT.
+ */
+ arizona->pdata.irq_flags = IRQF_TRIGGER_LOW;
+
+ /* Wait 200 ms after jack insertion */
+ arizona->pdata.micd_detect_debounce = 200;
+
+ /* Use standard AOSP values for headset-button mappings */
+ arizona->pdata.micd_ranges = arizona_micd_aosp_ranges;
+ arizona->pdata.num_micd_ranges = ARRAY_SIZE(arizona_micd_aosp_ranges);
+
+ return 0;
+}
+
+static const struct acpi_device_id arizona_acpi_match[] = {
+ {
+ .id = "WM510204",
+ .driver_data = WM5102,
+ },
+ {
+ .id = "WM510205",
+ .driver_data = WM5102,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, arizona_acpi_match);
+#else
+static int arizona_spi_acpi_probe(struct arizona *arizona)
+{
+ return -ENODEV;
+}
+#endif
+
static int arizona_spi_probe(struct spi_device *spi)
{
const struct spi_device_id *id = spi_get_device_id(spi);
@@ -77,6 +197,12 @@ static int arizona_spi_probe(struct spi_device *spi)
arizona->dev = &spi->dev;
arizona->irq = spi->irq;
+ if (has_acpi_companion(&spi->dev)) {
+ ret = arizona_spi_acpi_probe(arizona);
+ if (ret)
+ return ret;
+ }
+
return arizona_dev_init(arizona);
}
@@ -104,6 +230,7 @@ static struct spi_driver arizona_spi_driver = {
.name = "arizona",
.pm = &arizona_pm_ops,
.of_match_table = of_match_ptr(arizona_of_match),
+ .acpi_match_table = ACPI_PTR(arizona_acpi_match),
},
.probe = arizona_spi_probe,
.remove = arizona_spi_remove,