@@ -80,6 +80,15 @@ config USB_DWC3_KEYSTONE
Support of USB2/3 functionality in TI Keystone2 platforms.
Say 'Y' or 'M' here if you have one such device
+config USB_DWC3_ST
+ tristate "STMicroelectronics Platforms"
+ depends on ARCH_STI && OF
+ default USB_DWC3
+ help
+ STMicroelectronics SoCs with one DesignWare Core USB3 IP
+ inside (i.e. STiH407).
+ Say 'Y' or 'M' if you have one such device.
+
comment "Debugging features"
config USB_DWC3_DEBUG
@@ -33,3 +33,4 @@ obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
new file mode 100644
@@ -0,0 +1,377 @@
+/**
+ * dwc3-st.c Support for dwc3 platform devices on ST Microelectronics platforms
+ *
+ * This is a small driver for the dwc3 to provide the glue logic
+ * to configure the controller. Tested on STi platforms.
+ *
+ * Copyright (C) 2014 Stmicroelectronics
+ *
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ * Contributors: Aymen Bouattay <aymen.bouattay@st.com>
+ * Peter Griffin <peter.griffin@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Inspired by dwc3-omap.c and dwc3-exynos.c.
+ */
+
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/usb/of.h>
+
+#include "core.h"
+#include "io.h"
+
+/* glue registers */
+#define CLKRST_CTRL 0x00
+#define AUX_CLK_EN BIT(0)
+#define SW_PIPEW_RESET_N BIT(4)
+#define EXT_CFG_RESET_N BIT(8)
+/*
+ * 1'b0 : The host controller complies with the xHCI revision 0.96
+ * 1'b1 : The host controller complies with the xHCI revision 1.0
+ */
+#define XHCI_REVISION BIT(12)
+
+#define USB2_VBUS_MNGMNT_SEL1 0x2C
+/*
+ * For all fields in USB2_VBUS_MNGMNT_SEL1
+ * 2’b00 : Override value from Reg 0x30 is selected
+ * 2’b01 : utmiotg_<signal_name> from usb3_top is selected
+ * 2’b10 : pipew_<signal_name> from PIPEW instance is selected
+ * 2’b11 : value is 1'b0
+ */
+#define USB2_VBUS_REG30 0x0
+#define USB2_VBUS_UTMIOTG 0x1
+#define USB2_VBUS_PIPEW 0x2
+#define USB2_VBUS_ZERO 0x3
+
+#define SEL_OVERRIDE_VBUSVALID(n) (n << 0)
+#define SEL_OVERRIDE_POWERPRESENT(n) (n << 4)
+#define SEL_OVERRIDE_BVALID(n) (n << 8)
+
+/* Static DRD configuration */
+#define USB3_CONTROL_MASK 0xf77
+
+#define USB3_DEVICE_NOT_HOST BIT(0)
+#define USB3_FORCE_VBUSVALID BIT(1)
+#define USB3_DELAY_VBUSVALID BIT(2)
+#define USB3_SEL_FORCE_OPMODE BIT(4)
+#define USB3_FORCE_OPMODE(n) (n << 5)
+#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
+#define USB3_FORCE_DPPULLDOWN2 BIT(9)
+#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
+#define USB3_FORCE_DMPULLDOWN2 BIT(11)
+
+/**
+ * struct st_dwc3 - dwc3-st driver private structure
+ * @dev: device pointer
+ * @glue_base: ioaddr for the glue registers
+ * @regmap: regmap pointer for getting syscfg
+ * @syscfg_reg_off: usb syscfg control offset
+ * @dr_mode: drd static host/device config
+ * @rstc_pwrdn: rest controller for powerdown signal
+ * @rstc_rst: reset controller for softreset signal
+ */
+
+struct st_dwc3 {
+ struct device *dev;
+ void __iomem *glue_base;
+ struct regmap *regmap;
+ int syscfg_reg_off;
+ enum usb_dr_mode dr_mode;
+ struct reset_control *rstc_pwrdn;
+ struct reset_control *rstc_rst;
+};
+
+static inline u32 st_dwc3_readl(void __iomem *base, u32 offset)
+{
+ return readl_relaxed(base + offset);
+}
+
+static inline void st_dwc3_writel(void __iomem *base, u32 offset, u32 value)
+{
+ writel_relaxed(value, base + offset);
+}
+
+/**
+ * st_dwc3_drd_init: program the port
+ * @dwc3_data: driver private structure
+ * Description: this function is to program the port as either host or device
+ * according to the static configuration passed from devicetree.
+ * OTG and dual role are not yet supported!
+ */
+static int st_dwc3_drd_init(struct st_dwc3 *dwc3_data)
+{
+ u32 val;
+ int err;
+
+ err = regmap_read(dwc3_data->regmap, dwc3_data->syscfg_reg_off, &val);
+ if (err)
+ return err;
+
+ val &= USB3_CONTROL_MASK;
+
+ switch (dwc3_data->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+
+ val &= ~(USB3_FORCE_VBUSVALID | USB3_DELAY_VBUSVALID
+ | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
+ | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
+ | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
+
+ val |= USB3_DEVICE_NOT_HOST;
+
+ dev_dbg(dwc3_data->dev, "Configuring as Device\n");
+ break;
+
+ case USB_DR_MODE_HOST:
+
+ val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
+ | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
+ | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
+ | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
+
+ /*
+ * USB3_DELAY_VBUSVALID is ANDed with USB_C_VBUSVALID. Thus,
+ * when set to ‘0‘, it can delay the arrival of VBUSVALID
+ * information to VBUSVLDEXT2 input of the pico PHY.
+ * We don't want to do that so we set the bit to '1'.
+ */
+
+ val |= USB3_DELAY_VBUSVALID;
+
+ dev_dbg(dwc3_data->dev, "Configuring as Host\n");
+ break;
+
+ default:
+ dev_err(dwc3_data->dev, "Unsupported mode of operation %d\n",
+ dwc3_data->dr_mode);
+ return -EINVAL;
+ }
+
+ return regmap_write(dwc3_data->regmap, dwc3_data->syscfg_reg_off, val);
+}
+
+/**
+ * st_dwc3_init: init the controller via glue logic
+ * @dwc3_data: driver private structure
+ */
+static void st_dwc3_init(struct st_dwc3 *dwc3_data)
+{
+ u32 reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
+
+ reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
+ reg &= ~SW_PIPEW_RESET_N;
+ st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
+
+ /* configure mux for vbus, powerpresent and bvalid signals */
+ reg = st_dwc3_readl(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1);
+
+ reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
+ SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
+ SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
+
+ st_dwc3_writel(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1, reg);
+
+ reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
+ reg |= SW_PIPEW_RESET_N;
+ st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
+}
+
+static int st_dwc3_probe(struct platform_device *pdev)
+{
+ struct st_dwc3 *dwc3_data;
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->of_node, *child;
+ struct regmap *regmap;
+ int ret;
+
+ dwc3_data = devm_kzalloc(dev, sizeof(*dwc3_data), GFP_KERNEL);
+ if (!dwc3_data)
+ return -ENOMEM;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "reg-glue");
+ dwc3_data->glue_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(dwc3_data->glue_base))
+ return PTR_ERR(dwc3_data->glue_base);
+
+ regmap = syscon_regmap_lookup_by_phandle(node, "st,syscfg");
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ dma_set_coherent_mask(dev, dev->coherent_dma_mask);
+ dwc3_data->dev = dev;
+ dwc3_data->regmap = regmap;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "syscfg-reg");
+ if (!res) {
+ ret = -ENXIO;
+ goto undo_platform_dev_alloc;
+ }
+
+ dwc3_data->syscfg_reg_off = res->start;
+
+ dev_vdbg(&pdev->dev, "glue-logic addr 0x%p, syscfg-reg offset 0x%x\n",
+ dwc3_data->glue_base, dwc3_data->syscfg_reg_off);
+
+ dwc3_data->rstc_pwrdn = devm_reset_control_get(dev, "powerdown");
+ if (IS_ERR(dwc3_data->rstc_pwrdn)) {
+ dev_err(&pdev->dev, "could not get power controller\n");
+ ret = PTR_ERR(dwc3_data->rstc_pwrdn);
+ goto undo_platform_dev_alloc;
+ }
+
+ /* Manage PowerDown */
+ reset_control_deassert(dwc3_data->rstc_pwrdn);
+
+ dwc3_data->rstc_rst = devm_reset_control_get(dev, "softreset");
+ if (IS_ERR(dwc3_data->rstc_rst)) {
+ dev_err(&pdev->dev, "could not get reset controller\n");
+ ret = PTR_ERR(dwc3_data->rstc_pwrdn);
+ goto undo_powerdown;
+ }
+
+ /* Manage SoftReset */
+ reset_control_deassert(dwc3_data->rstc_rst);
+
+ child = of_get_child_by_name(node, "dwc3");
+ if (!child) {
+ dev_err(&pdev->dev, "failed to find dwc3 core node\n");
+ ret = -ENODEV;
+ goto undo_softreset;
+ }
+
+ dwc3_data->dr_mode = of_usb_get_dr_mode(child);
+
+ /* Allocate and initialize the core */
+ ret = of_platform_populate(node, NULL, NULL, dev);
+ if (ret) {
+ dev_err(dev, "failed to add dwc3 core\n");
+ goto undo_softreset;
+ }
+
+ /*
+ * Configure the USB port as device or host according to the static
+ * configuration passed from DT.
+ * DRD is the only mode currently supported so this will be enhanced
+ * as soon as OTG is available.
+ */
+ ret = st_dwc3_drd_init(dwc3_data);
+ if (ret) {
+ dev_err(dev, "drd initialisation failed\n");
+ goto undo_softreset;
+ }
+
+ /* ST glue logic init */
+ st_dwc3_init(dwc3_data);
+
+ platform_set_drvdata(pdev, dwc3_data);
+ return 0;
+
+undo_softreset:
+ reset_control_assert(dwc3_data->rstc_rst);
+undo_powerdown:
+ reset_control_assert(dwc3_data->rstc_pwrdn);
+undo_platform_dev_alloc:
+ platform_device_put(pdev);
+ return ret;
+}
+
+
+static int st_dwc3_remove_child(struct device *dev, void *c)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+
+ of_device_unregister(pdev);
+
+ return 0;
+}
+
+static int st_dwc3_remove(struct platform_device *pdev)
+{
+ struct st_dwc3 *dwc3_data = platform_get_drvdata(pdev);
+
+ device_for_each_child(&pdev->dev, NULL, st_dwc3_remove_child);
+
+ reset_control_assert(dwc3_data->rstc_pwrdn);
+ reset_control_assert(dwc3_data->rstc_rst);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int st_dwc3_suspend(struct device *dev)
+{
+ struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
+
+ reset_control_assert(dwc3_data->rstc_pwrdn);
+ reset_control_assert(dwc3_data->rstc_rst);
+
+ pinctrl_pm_select_sleep_state(dev);
+
+ return 0;
+}
+
+static int st_dwc3_resume(struct device *dev)
+{
+ struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
+ int ret;
+
+ pinctrl_pm_select_default_state(dev);
+
+ reset_control_deassert(dwc3_data->rstc_pwrdn);
+ reset_control_deassert(dwc3_data->rstc_rst);
+
+ ret = st_dwc3_drd_init(dwc3_data);
+ if (ret) {
+ dev_err(dev, "drd initialisation failed\n");
+ return ret;
+ }
+
+ /* ST glue logic init */
+ st_dwc3_init(dwc3_data);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static SIMPLE_DEV_PM_OPS(st_dwc3_dev_pm_ops, st_dwc3_suspend, st_dwc3_resume);
+
+static const struct of_device_id st_dwc3_match[] = {
+ { .compatible = "st,stih407-dwc3" },
+ { /* sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, st_dwc3_match);
+
+static struct platform_driver st_dwc3_driver = {
+ .probe = st_dwc3_probe,
+ .remove = st_dwc3_remove,
+ .driver = {
+ .name = "usb-st-dwc3",
+ .of_match_table = st_dwc3_match,
+ .pm = &st_dwc3_dev_pm_ops,
+ },
+};
+
+module_platform_driver(st_dwc3_driver);
+
+MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
+MODULE_DESCRIPTION("DesignWare USB3 STi Glue Layer");
+MODULE_LICENSE("GPL v2");