@@ -61,7 +61,7 @@ static unsigned int fmax = 515633;
* @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY
* is asserted (likewise for RX)
* @data_cmd_enable: enable value for data commands.
- * @sdio: variant supports SDIO
+ * @st_sdio: enable ST specific SDIO logic
* @st_clkdiv: true if using a ST-specific clock divider algorithm
* @datactrl_mask_ddrmode: ddr mode mask in datactrl register.
* @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
@@ -91,7 +91,7 @@ struct variant_data {
unsigned int data_cmd_enable;
unsigned int datactrl_mask_ddrmode;
unsigned int datactrl_mask_sdio;
- bool sdio;
+ bool st_sdio;
bool st_clkdiv;
bool blksz_datactrl16;
bool blksz_datactrl4;
@@ -141,7 +141,7 @@ static struct variant_data variant_u300 = {
.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
.datalength_bits = 16,
.datactrl_mask_sdio = MCI_ST_DPSM_SDIOEN,
- .sdio = true,
+ .st_sdio = true,
.pwrreg_powerup = MCI_PWR_ON,
.f_max = 100000000,
.signal_direction = true,
@@ -155,7 +155,7 @@ static struct variant_data variant_nomadik = {
.clkreg = MCI_CLK_ENABLE,
.datalength_bits = 24,
.datactrl_mask_sdio = MCI_ST_DPSM_SDIOEN,
- .sdio = true,
+ .st_sdio = true,
.st_clkdiv = true,
.pwrreg_powerup = MCI_PWR_ON,
.f_max = 100000000,
@@ -173,7 +173,7 @@ static struct variant_data variant_ux500 = {
.clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE,
.datalength_bits = 24,
.datactrl_mask_sdio = MCI_ST_DPSM_SDIOEN,
- .sdio = true,
+ .st_sdio = true,
.st_clkdiv = true,
.pwrreg_powerup = MCI_PWR_ON,
.f_max = 100000000,
@@ -193,7 +193,7 @@ static struct variant_data variant_ux500v2 = {
.datactrl_mask_ddrmode = MCI_ST_DPSM_DDRMODE,
.datalength_bits = 24,
.datactrl_mask_sdio = MCI_ST_DPSM_SDIOEN,
- .sdio = true,
+ .st_sdio = true,
.st_clkdiv = true,
.blksz_datactrl16 = true,
.pwrreg_powerup = MCI_PWR_ON,
@@ -820,26 +820,26 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
if (data->flags & MMC_DATA_READ)
datactrl |= MCI_DPSM_DIRECTION;
- if (variant->sdio && host->mmc->card)
- if (mmc_card_sdio(host->mmc->card)) {
- u32 clk;
- datactrl |= variant->datactrl_mask_sdio;
+ if (host->mmc->card && mmc_card_sdio(host->mmc->card)) {
+ u32 clk;
- /*
- * The ST Micro variant for SDIO small write transfers
- * needs to have clock H/W flow control disabled,
- * otherwise the transfer will not start. The threshold
- * depends on the rate of MCLK.
- */
- if (data->flags & MMC_DATA_WRITE &&
- (host->size < 8 ||
- (host->size <= 8 && host->mclk > 50000000)))
- clk = host->clk_reg & ~variant->clkreg_enable;
- else
- clk = host->clk_reg | variant->clkreg_enable;
+ datactrl |= variant->datactrl_mask_sdio;
- mmci_write_clkreg(host, clk);
- }
+ /*
+ * The ST Micro variant for SDIO small write transfers
+ * needs to have clock H/W flow control disabled,
+ * otherwise the transfer will not start. The threshold
+ * depends on the rate of MCLK.
+ */
+ if (variant->st_sdio && data->flags & MMC_DATA_WRITE &&
+ (host->size < 8 ||
+ (host->size <= 8 && host->mclk > 50000000)))
+ clk = host->clk_reg & ~variant->clkreg_enable;
+ else
+ clk = host->clk_reg | variant->clkreg_enable;
+
+ mmci_write_clkreg(host, clk);
+ }
if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 ||
host->mmc->ios.timing == MMC_TIMING_MMC_DDR52)
This patch renames sdio flag in vendor data to st_sdio, as this flag is only used to enable ST specific sdio setup. This will also ensure that the ST specfic setup is not done on other vendor like Qualcomm. Originally the issue was detected while testing WLAN ath6kl on IFC6410 board with APQ8064 SOC. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- drivers/mmc/host/mmci.c | 48 ++++++++++++++++++++++++------------------------ 1 file changed, 24 insertions(+), 24 deletions(-)