| Message ID | 20201223153925.73742-3-Jerome.Pouiller@silabs.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | wfx: get out from the staging area | expand |
On Wed, Dec 23, 2020 at 04:39:03PM +0100, Jerome Pouiller wrote: > From: Jérôme Pouiller <jerome.pouiller@silabs.com> Commit message? checkpatch.pl reports trailing whitespace errors. > > Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> > --- > .../bindings/net/wireless/silabs,wfx.yaml | 133 ++++++++++++++++++ > 1 file changed, 133 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml > > diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml > new file mode 100644 > index 000000000000..487d46c5fdc0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml > @@ -0,0 +1,133 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (c) 2020, Silicon Laboratories, Inc. > +%YAML 1.2 > +--- > + > +$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Silicon Labs WFxxx devicetree bindings > + > +maintainers: > + - Jérôme Pouiller <jerome.pouiller@silabs.com> > + > +description: > > + Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device > + from the WFxxx series is the WF200 described here: > + https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf > + > + The WF200 can be connected via SPI or via SDIO. > + > + For SDIO: > + > + Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is > + sufficient for the SDIO devices). > + > + It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without > + it, you may encounter issues during reboot. The mmc-pwrseq should be > + compatible with mmc-pwrseq-simple. Please consult > + Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt for more > + information. > + > + For SPI: > + > + In add of the properties below, please consult > + Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI > + related properties. > + > +properties: > + compatible: > + const: silabs,wf200 > + > + reg: > + description: > + When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is > + the chip select address of the device as defined in the SPI devices > + bindings. > + maxItems: 1 > + > + spi-max-frequency: true > + > + interrupts: > + description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and > + IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When > + SPI is used, this property is required. When SDIO is used, the "in-band" > + interrupt provided by the SDIO bus is used unless an interrupt is defined > + in the Device Tree. > + maxItems: 1 > + > + reset-gpios: > + description: (SPI only) Phandle of gpio that will be used to reset chip > + during probe. Without this property, you may encounter issues with warm > + boot. (For legacy purpose, the gpio in inverted when compatible == > + "silabs,wfx-spi") > + > + For SDIO, the reset gpio should declared using a mmc-pwrseq. > + maxItems: 1 > + > + wakeup-gpios: > + description: Phandle of gpio that will be used to wake-up chip. Without this > + property, driver will disable most of power saving features. > + maxItems: 1 > + > + silabs,antenna-config-file: > + $ref: /schemas/types.yaml#/definitions/string > + description: Use an alternative file for antenna configuration (aka > + "Platform Data Set" in Silabs jargon). Default is 'wf200.pds'. > + > + local-mac-address: true > + > + mac-address: true > + > +additionalProperties: false > + > +required: > + - compatible > + - reg > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + > + spi0 { > + #address-cells = <1>; > + #size-cells = <0>; > + > + wifi@0 { > + compatible = "silabs,wf200"; > + pinctrl-names = "default"; > + pinctrl-0 = <&wfx_irq &wfx_gpios>; > + reg = <0>; > + interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>; > + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; > + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; > + spi-max-frequency = <42000000>; > + }; > + }; > + > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + > + wfx_pwrseq: wfx_pwrseq { > + compatible = "mmc-pwrseq-simple"; > + pinctrl-names = "default"; > + pinctrl-0 = <&wfx_reset>; > + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; > + }; > + > + mmc0 { > + mmc-pwrseq = <&wfx_pwrseq>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + wifi@1 { > + compatible = "silabs,wf200"; > + pinctrl-names = "default"; > + pinctrl-0 = <&wfx_wakeup>; > + reg = <1>; > + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; > + }; > + }; > +... > -- > 2.29.2 >
diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml new file mode 100644 index 000000000000..487d46c5fdc0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020, Silicon Laboratories, Inc. +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Labs WFxxx devicetree bindings + +maintainers: + - Jérôme Pouiller <jerome.pouiller@silabs.com> + +description: > + Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device + from the WFxxx series is the WF200 described here: + https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf + + The WF200 can be connected via SPI or via SDIO. + + For SDIO: + + Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is + sufficient for the SDIO devices). + + It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without + it, you may encounter issues during reboot. The mmc-pwrseq should be + compatible with mmc-pwrseq-simple. Please consult + Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt for more + information. + + For SPI: + + In add of the properties below, please consult + Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI + related properties. + +properties: + compatible: + const: silabs,wf200 + + reg: + description: + When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is + the chip select address of the device as defined in the SPI devices + bindings. + maxItems: 1 + + spi-max-frequency: true + + interrupts: + description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and + IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When + SPI is used, this property is required. When SDIO is used, the "in-band" + interrupt provided by the SDIO bus is used unless an interrupt is defined + in the Device Tree. + maxItems: 1 + + reset-gpios: + description: (SPI only) Phandle of gpio that will be used to reset chip + during probe. Without this property, you may encounter issues with warm + boot. (For legacy purpose, the gpio in inverted when compatible == + "silabs,wfx-spi") + + For SDIO, the reset gpio should declared using a mmc-pwrseq. + maxItems: 1 + + wakeup-gpios: + description: Phandle of gpio that will be used to wake-up chip. Without this + property, driver will disable most of power saving features. + maxItems: 1 + + silabs,antenna-config-file: + $ref: /schemas/types.yaml#/definitions/string + description: Use an alternative file for antenna configuration (aka + "Platform Data Set" in Silabs jargon). Default is 'wf200.pds'. + + local-mac-address: true + + mac-address: true + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + wifi@0 { + compatible = "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_irq &wfx_gpios>; + reg = <0>; + interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + spi-max-frequency = <42000000>; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + wfx_pwrseq: wfx_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_reset>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + mmc0 { + mmc-pwrseq = <&wfx_pwrseq>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_wakeup>; + reg = <1>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + }; + }; +...