diff mbox series

[RFC,v2,8/8] arm64: dts: sparx5: Add the Sparx5 switch node

Message ID 20201217075134.919699-9-steen.hegelund@microchip.com
State Superseded
Headers show
Series Adding the Sparx5 Switch Driver | expand

Commit Message

Steen Hegelund Dec. 17, 2020, 7:51 a.m. UTC
This provides switchdev support for the Microship Sparx5 PCB134 and PCB135
reference boards.

This commit depends on the following series currently on their way
into the kernel:

- Sparx5 SerDes Driver
  Link: https://lore.kernel.org/r/20201211090541.157926-1-steen.hegelund@microchip.com/

- Serial GPIO Controller
  Link: https://lore.kernel.org/r/20201113145151.68900-1-lars.povlsen@microchip.com/

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
---
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |  60 ++
 .../dts/microchip/sparx5_pcb134_board.dtsi    | 424 ++++++++++--
 .../dts/microchip/sparx5_pcb135_board.dtsi    | 602 +++++++++++++++++-
 3 files changed, 1026 insertions(+), 60 deletions(-)

Comments

Andrew Lunn Dec. 19, 2020, 8:24 p.m. UTC | #1
> +		port13: port@13 {
> +			reg = <13>;
> +			/* Example: CU SFP, 1G speed */
> +			max-speed = <10000>;

One too many 0's for 1G.

> +		/* 25G SFPs */
> +		port56: port@56 {
> +			reg = <56>;
> +			max-speed = <10000>;

Why limit a 25G SFP to 10G?

    Andrew
Steen Hegelund Dec. 23, 2020, 2:31 p.m. UTC | #2
On 19.12.2020 21:24, Andrew Lunn wrote:
>EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>
>> +             port13: port@13 {
>> +                     reg = <13>;
>> +                     /* Example: CU SFP, 1G speed */
>> +                     max-speed = <10000>;
>
>One too many 0's for 1G.

Ah, but this is allocation for the port, not the speed.  This just
used by the calendar module to allocate slots on the taxis as requested.
So I would say it is OK to overallocate in this case (but you could
argue it does not make much sense).

>
>> +             /* 25G SFPs */
>> +             port56: port@56 {
>> +                     reg = <56>;
>> +                     max-speed = <10000>;
>
>Why limit a 25G SFP to 10G?

In the PCB134 case it is to keep the total allocation below 200Gbits
((12+8)*10G).  There is a port mux mode that provides 8*25G on the 25G
SerDes'es, but that would be a different DT.

The Datasheet shows which port mux combinations are possible, and not
all combinations of SerDes, Speed and interface are allowed.

The PCB134 was designed to showcase this "many 10G ports" mode, so that
is why we have the current DT.

>
>    Andrew

BR
Steen

---------------------------------------
Steen Hegelund
steen.hegelund@microchip.com
Andrew Lunn Dec. 23, 2020, 3:49 p.m. UTC | #3
On Wed, Dec 23, 2020 at 03:31:24PM +0100, Steen Hegelund wrote:
> On 19.12.2020 21:24, Andrew Lunn wrote:
> > EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> > 
> > > +             port13: port@13 {
> > > +                     reg = <13>;
> > > +                     /* Example: CU SFP, 1G speed */
> > > +                     max-speed = <10000>;
> > 
> > One too many 0's for 1G.
> 
> Ah, but this is allocation for the port, not the speed.

phylib will look for this property and change what the PHY advertises
based on this. There are some devices with Fast Ethernet but with a 1G
PHY, because they are cheaper. By setting max-speed=<100>; phylib will
stop the PHY advertising 1000Base-T/Full and 1000Base-T/Half. I can
imaging the same is used when the MAC can do 2.5G, but the PHY is 5G
capable, etc.

> This just used by the calendar module to allocate slots on the taxis
> as requested.  So I would say it is OK to overallocate in this case
> (but you could argue it does not make much sense).

Rather than misusing the max-speed property, it would be better to add
a property with your specific meaning.

  Andrew
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index e480238489fa..085ab5a4fa50 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -267,6 +267,21 @@  emmc_pins: emmc-pins {
 					"GPIO_46", "GPIO_47";
 				function = "emmc";
 			};
+
+			miim1_pins: miim1-pins {
+				pins = "GPIO_56", "GPIO_57";
+				function = "miim";
+			};
+
+			miim2_pins: miim2-pins {
+				pins = "GPIO_58", "GPIO_59";
+				function = "miim";
+			};
+
+			miim3_pins: miim3-pins {
+				pins = "GPIO_52", "GPIO_53";
+				function = "miim";
+			};
 		};
 
 		sgpio0: gpio@61101036c {
@@ -379,6 +394,44 @@  tmon0: tmon@610508110 {
 			clocks = <&ahb_clk>;
 		};
 
+		mdio0: mdio@6110102b0 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102b0 0x24>;
+		};
+
+		mdio1: mdio@6110102d4 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim1_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102d4 0x24>;
+		};
+
+		mdio2: mdio@6110102f8 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim2_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102d4 0x24>;
+		};
+
+		mdio3: mdio@61101031c {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim3_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x1101031c 0x24>;
+		};
+
 		serdes: serdes@10808000 {
 			compatible = "microchip,sparx5-serdes";
 			#phy-cells = <1>;
@@ -386,5 +439,12 @@  serdes: serdes@10808000 {
 			reg = <0x6 0x10808000 0x5d0000>;
 		};
 
+		switch: switch@610004000 {
+			compatible = "microchip,sparx5-switch";
+			reg =	<0x6 0x10004000 0x800000>,
+				<0x6 0x11010000 0x1b00000>;
+			reg-names = "devices", "gcb";
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index 6820579448d0..efa35cbcef49 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,30 +7,6 @@ 
 #include "sparx5_pcb_common.dtsi"
 
 /{
-	aliases {
-	    i2c0   = &i2c0;
-	    i2c100 = &i2c100;
-	    i2c101 = &i2c101;
-	    i2c102 = &i2c102;
-	    i2c103 = &i2c103;
-	    i2c104 = &i2c104;
-	    i2c105 = &i2c105;
-	    i2c106 = &i2c106;
-	    i2c107 = &i2c107;
-	    i2c108 = &i2c108;
-	    i2c109 = &i2c109;
-	    i2c110 = &i2c110;
-	    i2c111 = &i2c111;
-	    i2c112 = &i2c112;
-	    i2c113 = &i2c113;
-	    i2c114 = &i2c114;
-	    i2c115 = &i2c115;
-	    i2c116 = &i2c116;
-	    i2c117 = &i2c117;
-	    i2c118 = &i2c118;
-	    i2c119 = &i2c119;
-	};
-
 	gpio-restart {
 		compatible = "gpio-restart";
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -328,6 +304,11 @@  gpio@1 {
 	};
 };
 
+&sgpio2 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <0 0>, <11 31>;
+};
+
 &gpio {
 	i2cmux_pins_i: i2cmux-pins-i {
 	       pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
@@ -415,9 +396,9 @@  i2c0_emux: i2c0-emux@0 {
 
 &i2c0_imux {
 	pinctrl-names =
-		"i2c100", "i2c101", "i2c102", "i2c103",
-		"i2c104", "i2c105", "i2c106", "i2c107",
-		"i2c108", "i2c109", "i2c110", "i2c111", "idle";
+		"i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
+		"i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8",
+		"i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle";
 	pinctrl-0 = <&i2cmux_0>;
 	pinctrl-1 = <&i2cmux_1>;
 	pinctrl-2 = <&i2cmux_2>;
@@ -431,62 +412,62 @@  &i2c0_imux {
 	pinctrl-10 = <&i2cmux_10>;
 	pinctrl-11 = <&i2cmux_11>;
 	pinctrl-12 = <&i2cmux_pins_i>;
-	i2c100: i2c_sfp1 {
+	i2c_sfp1: i2c_sfp1 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c101: i2c_sfp2 {
+	i2c_sfp2: i2c_sfp2 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c102: i2c_sfp3 {
+	i2c_sfp3: i2c_sfp3 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c103: i2c_sfp4 {
+	i2c_sfp4: i2c_sfp4 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c104: i2c_sfp5 {
+	i2c_sfp5: i2c_sfp5 {
 		reg = <0x4>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c105: i2c_sfp6 {
+	i2c_sfp6: i2c_sfp6 {
 		reg = <0x5>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c106: i2c_sfp7 {
+	i2c_sfp7: i2c_sfp7 {
 		reg = <0x6>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c107: i2c_sfp8 {
+	i2c_sfp8: i2c_sfp8 {
 		reg = <0x7>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c108: i2c_sfp9 {
+	i2c_sfp9: i2c_sfp9 {
 		reg = <0x8>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c109: i2c_sfp10 {
+	i2c_sfp10: i2c_sfp10 {
 		reg = <0x9>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c110: i2c_sfp11 {
+	i2c_sfp11: i2c_sfp11 {
 		reg = <0xa>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c111: i2c_sfp12 {
+	i2c_sfp12: i2c_sfp12 {
 		reg = <0xb>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -499,44 +480,393 @@  &gpio 60 GPIO_ACTIVE_HIGH
 		     &gpio 61 GPIO_ACTIVE_HIGH
 		     &gpio 54 GPIO_ACTIVE_HIGH>;
 	idle-state = <0x8>;
-	i2c112: i2c_sfp13 {
+	i2c_sfp13: i2c_sfp13 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c113: i2c_sfp14 {
+	i2c_sfp14: i2c_sfp14 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c114: i2c_sfp15 {
+	i2c_sfp15: i2c_sfp15 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c115: i2c_sfp16 {
+	i2c_sfp16: i2c_sfp16 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c116: i2c_sfp17 {
+	i2c_sfp17: i2c_sfp17 {
 		reg = <0x4>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c117: i2c_sfp18 {
+	i2c_sfp18: i2c_sfp18 {
 		reg = <0x5>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c118: i2c_sfp19 {
+	i2c_sfp19: i2c_sfp19 {
 		reg = <0x6>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c119: i2c_sfp20 {
+	i2c_sfp20: i2c_sfp20 {
 		reg = <0x7>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
 };
+
+&mdio3 {
+	status = "ok";
+	phy64: ethernet-phy@64 {
+		reg = <28>;
+	};
+};
+
+&axi {
+	sfp_eth12: sfp-eth12 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth13: sfp-eth13 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth14: sfp-eth14 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth15: sfp-eth15 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp4>;
+		tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth48: sfp-eth48 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp5>;
+		tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth49: sfp-eth49 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp6>;
+		tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth50: sfp-eth50 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp7>;
+		tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth51: sfp-eth51 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp8>;
+		tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth52: sfp-eth52 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp9>;
+		tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth53: sfp-eth53 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp10>;
+		tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth54: sfp-eth54 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp11>;
+		tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth55: sfp-eth55 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp12>;
+		tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth56: sfp-eth56 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp13>;
+		tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth57: sfp-eth57 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp14>;
+		tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth58: sfp-eth58 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp15>;
+		tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth59: sfp-eth59 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp16>;
+		tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth60: sfp-eth60 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp17>;
+		tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth61: sfp-eth61 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp18>;
+		tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth62: sfp-eth62 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp19>;
+		tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth63: sfp-eth63 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp20>;
+		tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&switch {
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 10G SFPs */
+		port12: port@12 {
+			reg = <12>;
+			max-speed = <10000>;
+			phys = <&serdes 13>;
+			sfp = <&sfp_eth12>;
+			sd_sgpio = <301>;
+			managed = "in-band-status";
+		};
+		port13: port@13 {
+			reg = <13>;
+			/* Example: CU SFP, 1G speed */
+			max-speed = <10000>;
+			phys = <&serdes 14>;
+			sfp = <&sfp_eth13>;
+			sd_sgpio = <305>;
+			managed = "in-band-status";
+		};
+		port14: port@14 {
+			reg = <14>;
+			max-speed = <10000>;
+			phys = <&serdes 15>;
+			sfp = <&sfp_eth14>;
+			sd_sgpio = <309>;
+			managed = "in-band-status";
+		};
+		port15: port@15 {
+			reg = <15>;
+			max-speed = <10000>;
+			phys = <&serdes 16>;
+			sfp = <&sfp_eth15>;
+			sd_sgpio = <313>;
+			managed = "in-band-status";
+		};
+		port48: port@48 {
+			reg = <48>;
+			max-speed = <10000>;
+			phys = <&serdes 17>;
+			sfp = <&sfp_eth48>;
+			sd_sgpio = <317>;
+			managed = "in-band-status";
+		};
+		port49: port@49 {
+			reg = <49>;
+			max-speed = <10000>;
+			phys = <&serdes 18>;
+			sfp = <&sfp_eth49>;
+			sd_sgpio = <321>;
+			managed = "in-band-status";
+		};
+		port50: port@50 {
+			reg = <50>;
+			max-speed = <10000>;
+			phys = <&serdes 19>;
+			sfp = <&sfp_eth50>;
+			sd_sgpio = <325>;
+			managed = "in-band-status";
+		};
+		port51: port@51 {
+			reg = <51>;
+			max-speed = <10000>;
+			phys = <&serdes 20>;
+			sfp = <&sfp_eth51>;
+			sd_sgpio = <329>;
+			managed = "in-band-status";
+		};
+		port52: port@52 {
+			reg = <52>;
+			max-speed = <10000>;
+			phys = <&serdes 21>;
+			sfp = <&sfp_eth52>;
+			sd_sgpio = <333>;
+			managed = "in-band-status";
+		};
+		port53: port@53 {
+			reg = <53>;
+			max-speed = <10000>;
+			phys = <&serdes 22>;
+			sfp = <&sfp_eth53>;
+			sd_sgpio = <337>;
+			managed = "in-band-status";
+		};
+		port54: port@54 {
+			reg = <54>;
+			max-speed = <10000>;
+			phys = <&serdes 23>;
+			sfp = <&sfp_eth54>;
+			sd_sgpio = <341>;
+			managed = "in-band-status";
+		};
+		port55: port@55 {
+			reg = <55>;
+			max-speed = <10000>;
+			phys = <&serdes 24>;
+			sfp = <&sfp_eth55>;
+			sd_sgpio = <345>;
+			managed = "in-band-status";
+		};
+		/* 25G SFPs */
+		port56: port@56 {
+			reg = <56>;
+			max-speed = <10000>;
+			phys = <&serdes 25>;
+			sfp = <&sfp_eth56>;
+			sd_sgpio = <349>;
+			managed = "in-band-status";
+		};
+		port57: port@57 {
+			reg = <57>;
+			max-speed = <10000>;
+			phys = <&serdes 26>;
+			sfp = <&sfp_eth57>;
+			sd_sgpio = <353>;
+			managed = "in-band-status";
+		};
+		port58: port@58 {
+			reg = <58>;
+			max-speed = <10000>;
+			phys = <&serdes 27>;
+			sfp = <&sfp_eth58>;
+			sd_sgpio = <357>;
+			managed = "in-band-status";
+		};
+		port59: port@59 {
+			reg = <59>;
+			max-speed = <10000>;
+			phys = <&serdes 28>;
+			sfp = <&sfp_eth59>;
+			sd_sgpio = <361>;
+			managed = "in-band-status";
+		};
+		port60: port@60 {
+			reg = <60>;
+			max-speed = <10000>;
+			phys = <&serdes 29>;
+			sfp = <&sfp_eth60>;
+			sd_sgpio = <365>;
+			managed = "in-band-status";
+		};
+		port61: port@61 {
+			reg = <61>;
+			max-speed = <10000>;
+			phys = <&serdes 30>;
+			sfp = <&sfp_eth61>;
+			sd_sgpio = <369>;
+			managed = "in-band-status";
+		};
+		port62: port@62 {
+			reg = <62>;
+			max-speed = <10000>;
+			phys = <&serdes 31>;
+			sfp = <&sfp_eth62>;
+			sd_sgpio = <373>;
+			managed = "in-band-status";
+		};
+		port63: port@63 {
+			reg = <63>;
+			max-speed = <10000>;
+			phys = <&serdes 32>;
+			sfp = <&sfp_eth63>;
+			sd_sgpio = <377>;
+			managed = "in-band-status";
+		};
+		/* Finally the Management interface */
+		port64: port@64 {
+			reg = <64>;
+			max-speed = <1000>;
+			phys = <&serdes 0>;
+			phy-handle = <&phy64>;
+			phy-mode = "sgmii";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index e28c6dd16377..69e136c7bb9c 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,14 +7,6 @@ 
 #include "sparx5_pcb_common.dtsi"
 
 /{
-	aliases {
-	    i2c0   = &i2c0;
-	    i2c152 = &i2c152;
-	    i2c153 = &i2c153;
-	    i2c154 = &i2c154;
-	    i2c155 = &i2c155;
-	};
-
 	gpio-restart {
 		compatible = "gpio-restart";
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -138,6 +130,11 @@  gpio@1 {
 	};
 };
 
+&sgpio2 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+};
+
 &axi {
 	i2c0_imux: i2c0-imux@0 {
 		compatible = "i2c-mux-pinctrl";
@@ -149,31 +146,610 @@  i2c0_imux: i2c0-imux@0 {
 
 &i2c0_imux {
 	pinctrl-names =
-		"i2c152", "i2c153", "i2c154", "i2c155",
+		"i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
 		"idle";
 	pinctrl-0 = <&i2cmux_s29>;
 	pinctrl-1 = <&i2cmux_s30>;
 	pinctrl-2 = <&i2cmux_s31>;
 	pinctrl-3 = <&i2cmux_s32>;
 	pinctrl-4 = <&i2cmux_pins_i>;
-	i2c152: i2c_sfp1 {
+	i2c_sfp1: i2c_sfp1 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c153: i2c_sfp2 {
+	i2c_sfp2: i2c_sfp2 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c154: i2c_sfp3 {
+	i2c_sfp3: i2c_sfp3 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c155: i2c_sfp4 {
+	i2c_sfp4: i2c_sfp4 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
 };
+
+&axi {
+	sfp_eth60: sfp-eth60 {
+		compatible	   = "sff,sfp";
+		i2c-bus            = <&i2c_sfp1>;
+		tx-disable-gpios   = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth61: sfp-eth61 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp2>;
+		tx-disable-gpios   = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth62: sfp-eth62 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp3>;
+		tx-disable-gpios   = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth63: sfp-eth63 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp4>;
+		tx-disable-gpios   = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdio0 {
+	status = "ok";
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+	phy2: ethernet-phy@2 {
+		reg = <2>;
+	};
+	phy3: ethernet-phy@3 {
+		reg = <3>;
+	};
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+	phy5: ethernet-phy@5 {
+		reg = <5>;
+	};
+	phy6: ethernet-phy@6 {
+		reg = <6>;
+	};
+	phy7: ethernet-phy@7 {
+		reg = <7>;
+	};
+	phy8: ethernet-phy@8 {
+		reg = <8>;
+	};
+	phy9: ethernet-phy@9 {
+		reg = <9>;
+	};
+	phy10: ethernet-phy@10 {
+		reg = <10>;
+	};
+	phy11: ethernet-phy@11 {
+		reg = <11>;
+	};
+	phy12: ethernet-phy@12 {
+		reg = <12>;
+	};
+	phy13: ethernet-phy@13 {
+		reg = <13>;
+	};
+	phy14: ethernet-phy@14 {
+		reg = <14>;
+	};
+	phy15: ethernet-phy@15 {
+		reg = <15>;
+	};
+	phy16: ethernet-phy@16 {
+		reg = <16>;
+	};
+	phy17: ethernet-phy@17 {
+		reg = <17>;
+	};
+	phy18: ethernet-phy@18 {
+		reg = <18>;
+	};
+	phy19: ethernet-phy@19 {
+		reg = <19>;
+	};
+	phy20: ethernet-phy@20 {
+		reg = <20>;
+	};
+	phy21: ethernet-phy@21 {
+		reg = <21>;
+	};
+	phy22: ethernet-phy@22 {
+		reg = <22>;
+	};
+	phy23: ethernet-phy@23 {
+		reg = <23>;
+	};
+};
+
+&mdio1 {
+	status = "ok";
+	phy24: ethernet-phy@24 {
+		reg = <0>;
+	};
+	phy25: ethernet-phy@25 {
+		reg = <1>;
+	};
+	phy26: ethernet-phy@26 {
+		reg = <2>;
+	};
+	phy27: ethernet-phy@27 {
+		reg = <3>;
+	};
+	phy28: ethernet-phy@28 {
+		reg = <4>;
+	};
+	phy29: ethernet-phy@29 {
+		reg = <5>;
+	};
+	phy30: ethernet-phy@30 {
+		reg = <6>;
+	};
+	phy31: ethernet-phy@31 {
+		reg = <7>;
+	};
+	phy32: ethernet-phy@32 {
+		reg = <8>;
+	};
+	phy33: ethernet-phy@33 {
+		reg = <9>;
+	};
+	phy34: ethernet-phy@34 {
+		reg = <10>;
+	};
+	phy35: ethernet-phy@35 {
+		reg = <11>;
+	};
+	phy36: ethernet-phy@36 {
+		reg = <12>;
+	};
+	phy37: ethernet-phy@37 {
+		reg = <13>;
+	};
+	phy38: ethernet-phy@38 {
+		reg = <14>;
+	};
+	phy39: ethernet-phy@39 {
+		reg = <15>;
+	};
+	phy40: ethernet-phy@40 {
+		reg = <16>;
+	};
+	phy41: ethernet-phy@41 {
+		reg = <17>;
+	};
+	phy42: ethernet-phy@42 {
+		reg = <18>;
+	};
+	phy43: ethernet-phy@43 {
+		reg = <19>;
+	};
+	phy44: ethernet-phy@44 {
+		reg = <20>;
+	};
+	phy45: ethernet-phy@45 {
+		reg = <21>;
+	};
+	phy46: ethernet-phy@46 {
+		reg = <22>;
+	};
+	phy47: ethernet-phy@47 {
+		reg = <23>;
+	};
+};
+
+&mdio3 {
+	status = "ok";
+	phy64: ethernet-phy@64 {
+		reg = <28>;
+	};
+};
+
+&switch {
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port0: port@0 {
+			reg = <0>;
+			max-speed = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy0>;
+			phy-mode = "qsgmii";
+		};
+		port1: port@1 {
+			reg = <1>;
+			max-speed = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy1>;
+			phy-mode = "qsgmii";
+		};
+		port2: port@2 {
+			reg = <2>;
+			max-speed = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy2>;
+			phy-mode = "qsgmii";
+		};
+		port3: port@3 {
+			reg = <3>;
+			max-speed = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy3>;
+			phy-mode = "qsgmii";
+		};
+		port4: port@4 {
+			reg = <4>;
+			max-speed = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy4>;
+			phy-mode = "qsgmii";
+		};
+		port5: port@5 {
+			reg = <5>;
+			max-speed = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy5>;
+			phy-mode = "qsgmii";
+		};
+		port6: port@6 {
+			reg = <6>;
+			max-speed = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy6>;
+			phy-mode = "qsgmii";
+		};
+		port7: port@7 {
+			reg = <7>;
+			max-speed = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy7>;
+			phy-mode = "qsgmii";
+		};
+		port8: port@8 {
+			reg = <8>;
+			max-speed = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy8>;
+			phy-mode = "qsgmii";
+		};
+		port9: port@9 {
+			reg = <9>;
+			max-speed = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy9>;
+			phy-mode = "qsgmii";
+		};
+		port10: port@10 {
+			reg = <10>;
+			max-speed = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy10>;
+			phy-mode = "qsgmii";
+		};
+		port11: port@11 {
+			reg = <11>;
+			max-speed = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy11>;
+			phy-mode = "qsgmii";
+		};
+		port12: port@12 {
+			reg = <12>;
+			max-speed = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy12>;
+			phy-mode = "qsgmii";
+		};
+		port13: port@13 {
+			reg = <13>;
+			max-speed = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy13>;
+			phy-mode = "qsgmii";
+		};
+		port14: port@14 {
+			reg = <14>;
+			max-speed = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy14>;
+			phy-mode = "qsgmii";
+		};
+		port15: port@15 {
+			reg = <15>;
+			max-speed = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy15>;
+			phy-mode = "qsgmii";
+		};
+		port16: port@16 {
+			reg = <16>;
+			max-speed = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy16>;
+			phy-mode = "qsgmii";
+		};
+		port17: port@17 {
+			reg = <17>;
+			max-speed = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy17>;
+			phy-mode = "qsgmii";
+		};
+		port18: port@18 {
+			reg = <18>;
+			max-speed = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy18>;
+			phy-mode = "qsgmii";
+		};
+		port19: port@19 {
+			reg = <19>;
+			max-speed = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy19>;
+			phy-mode = "qsgmii";
+		};
+		port20: port@20 {
+			reg = <20>;
+			max-speed = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy20>;
+			phy-mode = "qsgmii";
+		};
+		port21: port@21 {
+			reg = <21>;
+			max-speed = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy21>;
+			phy-mode = "qsgmii";
+		};
+		port22: port@22 {
+			reg = <22>;
+			max-speed = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy22>;
+			phy-mode = "qsgmii";
+		};
+		port23: port@23 {
+			reg = <23>;
+			max-speed = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy23>;
+			phy-mode = "qsgmii";
+		};
+		port24: port@24 {
+			reg = <24>;
+			max-speed = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy24>;
+			phy-mode = "qsgmii";
+		};
+		port25: port@25 {
+			reg = <25>;
+			max-speed = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy25>;
+			phy-mode = "qsgmii";
+		};
+		port26: port@26 {
+			reg = <26>;
+			max-speed = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy26>;
+			phy-mode = "qsgmii";
+		};
+		port27: port@27 {
+			reg = <27>;
+			max-speed = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy27>;
+			phy-mode = "qsgmii";
+		};
+		port28: port@28 {
+			reg = <28>;
+			max-speed = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy28>;
+			phy-mode = "qsgmii";
+		};
+		port29: port@29 {
+			reg = <29>;
+			max-speed = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy29>;
+			phy-mode = "qsgmii";
+		};
+		port30: port@30 {
+			reg = <30>;
+			max-speed = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy30>;
+			phy-mode = "qsgmii";
+		};
+		port31: port@31 {
+			reg = <31>;
+			max-speed = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy31>;
+			phy-mode = "qsgmii";
+		};
+		port32: port@32 {
+			reg = <32>;
+			max-speed = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy32>;
+			phy-mode = "qsgmii";
+		};
+		port33: port@33 {
+			reg = <33>;
+			max-speed = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy33>;
+			phy-mode = "qsgmii";
+		};
+		port34: port@34 {
+			reg = <34>;
+			max-speed = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy34>;
+			phy-mode = "qsgmii";
+		};
+		port35: port@35 {
+			reg = <35>;
+			max-speed = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy35>;
+			phy-mode = "qsgmii";
+		};
+		port36: port@36 {
+			reg = <36>;
+			max-speed = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy36>;
+			phy-mode = "qsgmii";
+		};
+		port37: port@37 {
+			reg = <37>;
+			max-speed = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy37>;
+			phy-mode = "qsgmii";
+		};
+		port38: port@38 {
+			reg = <38>;
+			max-speed = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy38>;
+			phy-mode = "qsgmii";
+		};
+		port39: port@39 {
+			reg = <39>;
+			max-speed = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy39>;
+			phy-mode = "qsgmii";
+		};
+		port40: port@40 {
+			reg = <40>;
+			max-speed = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy40>;
+			phy-mode = "qsgmii";
+		};
+		port41: port@41 {
+			reg = <41>;
+			max-speed = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy41>;
+			phy-mode = "qsgmii";
+		};
+		port42: port@42 {
+			reg = <42>;
+			max-speed = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy42>;
+			phy-mode = "qsgmii";
+		};
+		port43: port@43 {
+			reg = <43>;
+			max-speed = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy43>;
+			phy-mode = "qsgmii";
+		};
+		port44: port@44 {
+			reg = <44>;
+			max-speed = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy44>;
+			phy-mode = "qsgmii";
+		};
+		port45: port@45 {
+			reg = <45>;
+			max-speed = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy45>;
+			phy-mode = "qsgmii";
+		};
+		port46: port@46 {
+			reg = <46>;
+			max-speed = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy46>;
+			phy-mode = "qsgmii";
+		};
+		port47: port@47 {
+			reg = <47>;
+			max-speed = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy47>;
+			phy-mode = "qsgmii";
+		};
+		/* Then the 25G interfaces */
+		port60: port@60 {
+			reg = <60>;
+			max-speed = <25000>;
+			phys = <&serdes 29>;
+			sfp = <&sfp_eth60>;
+			managed = "in-band-status";
+		};
+		port61: port@61 {
+			reg = <61>;
+			max-speed = <25000>;
+			phys = <&serdes 30>;
+			sfp = <&sfp_eth61>;
+			managed = "in-band-status";
+		};
+		port62: port@62 {
+			reg = <62>;
+			max-speed = <25000>;
+			phys = <&serdes 31>;
+			sfp = <&sfp_eth62>;
+			managed = "in-band-status";
+		};
+		port63: port@63 {
+			reg = <63>;
+			max-speed = <25000>;
+			phys = <&serdes 32>;
+			sfp = <&sfp_eth63>;
+			managed = "in-band-status";
+		};
+		/* Finally the Management interface */
+		port64: port@64 {
+			reg = <64>;
+			max-speed = <1000>;
+			phys = <&serdes 0>;
+			phy-handle = <&phy64>;
+			phy-mode = "sgmii";
+		};
+	};
+};