diff mbox series

[1/3] cfg80211: Add wiphy flag to trigger STA disconnect after hardware restart

Message ID 20201215173021.5884-1-youghand@codeaurora.org
State Superseded
Headers show
Series [1/3] cfg80211: Add wiphy flag to trigger STA disconnect after hardware restart | expand

Commit Message

Youghandhar Chintala Dec. 15, 2020, 5:30 p.m. UTC
Many wifi drivers (e.g. ath10k using qualcomm wifi chipsets)
support silent target hardware restart/recovery. Out of these
drivers which support target hw restart, certain chipsets
have the wifi mac sequence number addition for transmitted
frames done by the firmware. For such chipsets, a silent
target hardware restart breaks the continuity of the wifi
mac sequence number, since the wifi mac sequence number
restarts from 0 after the restart, which in-turn leads
to the peer access point dropping all the frames from device
until it receives the frame with the mac sequence which was
expected by the AP.

Add a wiphy flag for the driver to indicate that it needs a
trigger for STA disconnect after hardware restart.

Tested on ath10k using WCN3990, QCA6174.

Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
---
 include/net/cfg80211.h | 4 ++++
 1 file changed, 4 insertions(+)

Comments

Abhishek Kumar Feb. 5, 2021, 10:02 p.m. UTC | #1
LGTM! If no one has any objections, I would be happy to see this
considered for upstream.

Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>

Thanks
Abhishek

On Tue, Dec 15, 2020 at 9:30 AM Youghandhar Chintala
<youghand@codeaurora.org> wrote:
>
> Many wifi drivers (e.g. ath10k using qualcomm wifi chipsets)
> support silent target hardware restart/recovery. Out of these
> drivers which support target hw restart, certain chipsets
> have the wifi mac sequence number addition for transmitted
> frames done by the firmware. For such chipsets, a silent
> target hardware restart breaks the continuity of the wifi
> mac sequence number, since the wifi mac sequence number
> restarts from 0 after the restart, which in-turn leads
> to the peer access point dropping all the frames from device
> until it receives the frame with the mac sequence which was
> expected by the AP.
>
> Add a wiphy flag for the driver to indicate that it needs a
> trigger for STA disconnect after hardware restart.
>
> Tested on ath10k using WCN3990, QCA6174.
>
> Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
> ---
>  include/net/cfg80211.h | 4 ++++
>  1 file changed, 4 insertions(+)
>
> diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
> index ab249ca..7fba6f6 100644
> --- a/include/net/cfg80211.h
> +++ b/include/net/cfg80211.h
> @@ -4311,6 +4311,9 @@ struct cfg80211_ops {
>   * @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
>   *     before connection.
>   * @WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK: The device supports bigger kek and kck keys
> + * @WIPHY_FLAG_STA_DISCONNECT_ON_HW_RESTART: The device needs a trigger to
> + *     disconnect STA after target hardware restart. This flag should be
> + *     exposed by drivers which support target recovery.
>   */
>  enum wiphy_flags {
>         WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK         = BIT(0),
> @@ -4337,6 +4340,7 @@ enum wiphy_flags {
>         WIPHY_FLAG_SUPPORTS_5_10_MHZ            = BIT(22),
>         WIPHY_FLAG_HAS_CHANNEL_SWITCH           = BIT(23),
>         WIPHY_FLAG_HAS_STATIC_WEP               = BIT(24),
> +       WIPHY_FLAG_STA_DISCONNECT_ON_HW_RESTART = BIT(25),
>  };
>
>  /**
> --
> 2.7.4
>
Johannes Berg Feb. 12, 2021, 8:36 a.m. UTC | #2
On Tue, 2020-12-15 at 23:00 +0530, Youghandhar Chintala wrote:
> 

>   * @WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK: The device supports bigger kek and kck keys

> + * @WIPHY_FLAG_STA_DISCONNECT_ON_HW_RESTART: The device needs a trigger to

> + *	disconnect STA after target hardware restart. This flag should be

> + *	exposed by drivers which support target recovery.


You're not doing anything with this information in cfg80211, so
consequently it doesn't belong there.

johannes
diff mbox series

Patch

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index ab249ca..7fba6f6 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -4311,6 +4311,9 @@  struct cfg80211_ops {
  * @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
  *	before connection.
  * @WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK: The device supports bigger kek and kck keys
+ * @WIPHY_FLAG_STA_DISCONNECT_ON_HW_RESTART: The device needs a trigger to
+ *	disconnect STA after target hardware restart. This flag should be
+ *	exposed by drivers which support target recovery.
  */
 enum wiphy_flags {
 	WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK		= BIT(0),
@@ -4337,6 +4340,7 @@  enum wiphy_flags {
 	WIPHY_FLAG_SUPPORTS_5_10_MHZ		= BIT(22),
 	WIPHY_FLAG_HAS_CHANNEL_SWITCH		= BIT(23),
 	WIPHY_FLAG_HAS_STATIC_WEP		= BIT(24),
+	WIPHY_FLAG_STA_DISCONNECT_ON_HW_RESTART	= BIT(25),
 };
 
 /**