@@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
#define BTUSB_WIDEBAND_SPEECH 0x400000
#define BTUSB_VALID_LE_STATES 0x800000
#define BTUSB_QCA_WCN6855 0x1000000
+#define BTUSB_INTEL_NEWGEN 0x2000000
static const struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
@@ -2716,6 +2717,128 @@ static int btusb_setup_intel_new(struct hci_dev *hdev)
return 0;
}
+static int btusb_setup_intel_newgen(struct hci_dev *hdev)
+{
+ struct btusb_data *data = hci_get_drvdata(hdev);
+ u32 boot_param;
+ char ddcname[64];
+ ktime_t calltime, delta, rettime;
+ unsigned long long duration;
+ int err;
+ struct intel_debug_features features;
+ struct intel_version_tlv version;
+
+ bt_dev_dbg(hdev, "");
+
+ /* Set the default boot parameter to 0x0 and it is updated to
+ * SKU specific boot parameter after reading Intel_Write_Boot_Params
+ * command while downloading the firmware.
+ */
+ boot_param = 0x00000000;
+
+ calltime = ktime_get();
+
+ /* Read the Intel version information to determine if the device
+ * is in bootloader mode or if it already has operational firmware
+ * loaded.
+ */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err) {
+ bt_dev_err(hdev, "Intel Read version failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ btintel_version_info_tlv(hdev, &version);
+
+ /* check if controller is already having an operational firmware */
+ if (version.img_type == 0x03)
+ goto finish;
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
+
+ calltime = ktime_get();
+
+ set_bit(BTUSB_BOOTING, &data->flags);
+
+ err = btintel_send_intel_reset(hdev, boot_param);
+ if (err) {
+ bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ /* The bootloader will not indicate when the device is ready. This
+ * is done by the operational firmware sending bootup notification.
+ *
+ * Booting into operational firmware should not take longer than
+ * 1 second. However if that happens, then just fail the setup
+ * since something went wrong.
+ */
+ bt_dev_info(hdev, "Waiting for device to boot");
+
+ err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
+ TASK_INTERRUPTIBLE,
+ msecs_to_jiffies(1000));
+
+ if (err == -EINTR) {
+ bt_dev_err(hdev, "Device boot interrupted");
+ return -EINTR;
+ }
+
+ if (err) {
+ bt_dev_err(hdev, "Device boot timeout");
+ btintel_reset_to_bootloader(hdev);
+ return -ETIMEDOUT;
+ }
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Device booted in %llu usecs", duration);
+
+ clear_bit(BTUSB_BOOTLOADER, &data->flags);
+
+ /* Once the device is running in operational mode, it needs to
+ * apply the device configuration (DDC) parameters.
+ *
+ * The device can work without DDC parameters, so even if it
+ * fails to load the file, no need to fail the setup.
+ */
+ btintel_load_ddc_config(hdev, ddcname);
+
+ /* Read the Intel supported features and if new exception formats
+ * supported, need to load the additional DDC config to enable.
+ */
+ btintel_read_debug_features(hdev, &features);
+
+ /* Set DDC mask for available debug features */
+ btintel_set_debug_features(hdev, &features);
+
+ /* Read the Intel version information after loading the FW */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err)
+ return err;
+
+ btintel_version_info_tlv(hdev, &version);
+
+finish:
+ /* Set the event mask for Intel specific vendor events. This enables
+ * a few extra events that are useful during general operation. It
+ * does not enable any debugging related events.
+ *
+ * The device will function correctly without these events enabled
+ * and thus no need to fail the setup.
+ */
+ btintel_set_event_mask(hdev, false);
+
+ return 0;
+}
static int btusb_shutdown_intel(struct hci_dev *hdev)
{
struct sk_buff *skb;
@@ -4101,6 +4224,24 @@ static int btusb_probe(struct usb_interface *intf,
set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
}
+ if (id->driver_info & BTUSB_INTEL_NEWGEN) {
+ hdev->manufacturer = 2;
+ hdev->send = btusb_send_frame_intel;
+ hdev->setup = btusb_setup_intel_newgen;
+ hdev->shutdown = btusb_shutdown_intel_new;
+ hdev->hw_error = btintel_hw_error;
+ hdev->set_diag = btintel_set_diag;
+ hdev->set_bdaddr = btintel_set_bdaddr;
+ hdev->cmd_timeout = btusb_intel_cmd_timeout;
+ set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
+ set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
+ set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
+
+ data->recv_event = btusb_recv_event_intel;
+ data->recv_bulk = btusb_recv_bulk_intel;
+ set_bit(BTUSB_BOOTLOADER, &data->flags);
+ }
+
if (id->driver_info & BTUSB_MARVELL)
hdev->set_bdaddr = btusb_set_bdaddr_marvell;