diff mbox series

[v2,1/2] MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.

Message ID 20201116175508.51943-2-zhouyanjie@wanyeetech.com
State Accepted
Commit 158c774d3c64859e84dd20e04d5fb18c8d3d318e
Headers show
Series Add missing nodes and refresh defconfig for Ingenic SoCs based boards. | expand

Commit Message

Zhou Yanjie Nov. 16, 2020, 5:55 p.m. UTC
1.Add OTG/OTG PHY/RNG nodes for JZ4780, CGU/OTG nodes for CI20.
2.Add OTG/OTG PHY/RNG/OST nodes for X1000, SSI/CGU/OST/OTG/SC16IS752
  nodes for CU1000-Neo.
3.Add OTG/OTG PHY/DTRNG/OST nodes for X1830, SSI/CGU/OST/OTG/SC16IS752
  nodes for CU1830-Neo.

Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Tested by: H. Nikolaus Schaller <hns@goldelico.com> # CI20/jz4780
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---

Notes:
    v1->v2:
    1.Add the otg_power node for otg_phy's vcc_supply.
    2.Move assigned-clocks in the otg node into the cgu node.
    3.Move the position of the SSI node.

 arch/mips/boot/dts/ingenic/ci20.dts       | 45 +++++++++++++++++++--
 arch/mips/boot/dts/ingenic/cu1000-neo.dts | 62 ++++++++++++++++++++++++++---
 arch/mips/boot/dts/ingenic/cu1830-neo.dts | 66 ++++++++++++++++++++++++++++---
 arch/mips/boot/dts/ingenic/jz4780.dtsi    | 45 ++++++++++++++++++++-
 arch/mips/boot/dts/ingenic/x1000.dtsi     | 56 +++++++++++++++++++++++++-
 arch/mips/boot/dts/ingenic/x1830.dtsi     | 58 ++++++++++++++++++++++++++-
 6 files changed, 313 insertions(+), 19 deletions(-)
diff mbox series

Patch

diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 75f5bfbf2c37..8877c62609de 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -69,9 +69,11 @@ 
 
 	eth0_power: fixedregulator@0 {
 		compatible = "regulator-fixed";
+
 		regulator-name = "eth0_power";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+
 		gpio = <&gpb 25 GPIO_ACTIVE_LOW>;
 		enable-active-high;
 	};
@@ -83,16 +85,39 @@ 
 
 	wlan0_power: fixedregulator@1 {
 		compatible = "regulator-fixed";
+
 		regulator-name = "wlan0_power";
+
 		gpio = <&gpb 19 GPIO_ACTIVE_LOW>;
 		enable-active-high;
 	};
+
+	otg_power: fixedregulator@2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "otg_power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
 };
 
 &ext {
 	clock-frequency = <48000000>;
 };
 
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>;
+	assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>;
+	assigned-clock-rates = <48000000>;
+};
+
 &mmc0 {
 	status = "okay";
 
@@ -396,6 +421,16 @@ 
 	status = "okay";
 };
 
+&otg_phy {
+	status = "okay";
+
+	vcc-supply = <&otg_power>;
+};
+
+&otg {
+	status = "okay";
+};
+
 &pinctrl {
 	pins_uart0: uart0 {
 		function = "uart0";
@@ -489,7 +524,11 @@ 
 };
 
 &tcu {
-	/* 3 MHz for the system timer and clocksource */
-	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>;
-	assigned-clock-rates = <3000000>, <3000000>;
+	/*
+	 * 750 kHz for the system timer and 3 MHz for the clocksource,
+	 * use channel #0 for the system timer, #1 for the clocksource.
+	 */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+					  <&tcu TCU_CLK_OST>;
+	assigned-clock-rates = <750000>, <3000000>, <3000000>;
 };
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index 22a1066d637b..f98cf029efc3 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -3,7 +3,7 @@ 
 
 #include "x1000.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/ingenic,sysost.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -31,6 +31,42 @@ 
 		};
 	};
 
+	ssi: spi-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		num-chipselects = <1>;
+
+		mosi-gpios = <&gpd 2 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpd 3 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpd 0 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpd 1 GPIO_ACTIVE_HIGH>;
+
+		status = "okay";
+
+		spi-max-frequency = <50000000>;
+
+		sc16is752: expander@0 {
+			compatible = "nxp,sc16is752";
+			reg = <0>; /* CE0 */
+			spi-max-frequency = <4000000>;
+
+			clocks = <&exclk_sc16is752>;
+
+			interrupt-parent = <&gpc>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			exclk_sc16is752: sc16is752 {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <48000000>;
+			};
+		};
+	};
+
 	wlan_pwrseq: msc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 
@@ -43,13 +79,19 @@ 
 	clock-frequency = <24000000>;
 };
 
-&tcu {
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu X1000_CLK_RTC>;
+	assigned-clock-parents = <&cgu X1000_CLK_RTCLK>;
+};
+
+&ost {
 	/* 1500 kHz for the system timer and clocksource */
-	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
 	assigned-clock-rates = <1500000>, <1500000>;
-
-	/* Use channel #0 for the system timer channel #2 for the clocksource */
-	ingenic,pwm-channels-mask = <0xfa>;
 };
 
 &uart2 {
@@ -135,6 +177,14 @@ 
 	};
 };
 
+&otg_phy {
+	status = "okay";
+};
+
+&otg {
+	status = "okay";
+};
+
 &pinctrl {
 	pins_uart2: uart2 {
 		function = "uart2";
diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
index 640f96c00d63..cfcb40edb7d9 100644
--- a/arch/mips/boot/dts/ingenic/cu1830-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
@@ -3,7 +3,7 @@ 
 
 #include "x1830.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/ingenic,sysost.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -31,6 +31,42 @@ 
 		};
 	};
 
+	ssi0: spi-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		num-chipselects = <1>;
+
+		mosi-gpios = <&gpc 12 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpc 11 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpc 16 GPIO_ACTIVE_HIGH>;
+
+		status = "okay";
+
+		spi-max-frequency = <50000000>;
+
+		sc16is752: expander@0 {
+			compatible = "nxp,sc16is752";
+			reg = <0>; /* CE0 */
+			spi-max-frequency = <4000000>;
+
+			clocks = <&exclk_sc16is752>;
+
+			interrupt-parent = <&gpb>;
+			interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			exclk_sc16is752: sc16is752 {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <48000000>;
+			};
+		};
+	};
+
 	wlan_pwrseq: msc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 
@@ -43,13 +79,19 @@ 
 	clock-frequency = <24000000>;
 };
 
-&tcu {
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu X1830_CLK_RTC>;
+	assigned-clock-parents = <&cgu X1830_CLK_RTCLK>;
+};
+
+&ost {
 	/* 1500 kHz for the system timer and clocksource */
-	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
 	assigned-clock-rates = <1500000>, <1500000>;
-
-	/* Use channel #0 for the system timer channel #2 for the clocksource */
-	ingenic,pwm-channels-mask = <0xfa>;
 };
 
 &uart1 {
@@ -73,6 +115,10 @@ 
 	};
 };
 
+&dtrng {
+	status = "okay";
+};
+
 &msc0 {
 	status = "okay";
 
@@ -135,6 +181,14 @@ 
 	};
 };
 
+&otg_phy {
+	status = "okay";
+};
+
+&otg {
+	status = "okay";
+};
+
 &pinctrl {
 	pins_uart1: uart1 {
 		function = "uart1";
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index dfb5a7e1bb21..8d01feef7ff5 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -61,13 +61,34 @@ 
 	};
 
 	cgu: jz4780-cgu@10000000 {
-		compatible = "ingenic,jz4780-cgu";
+		compatible = "ingenic,jz4780-cgu", "simple-mfd";
 		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
+
+		#clock-cells = <1>;
 
 		clocks = <&ext>, <&rtc>;
 		clock-names = "ext", "rtc";
 
-		#clock-cells = <1>;
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,jz4780-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu JZ4780_CLK_OTG1>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		rng: rng@d8 {
+			compatible = "ingenic,jz4780-rng";
+			reg = <0xd8 0x8>;
+
+			status = "disabled";
+		};
 	};
 
 	tcu: timer@10002000 {
@@ -494,4 +515,24 @@ 
 
 		status = "disabled";
 	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,jz4780-otg", "snps,dwc2";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu JZ4780_CLK_UHC>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
 };
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index 1f1f896dd1f7..aac9dedaf334 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -52,13 +52,47 @@ 
 	};
 
 	cgu: x1000-cgu@10000000 {
-		compatible = "ingenic,x1000-cgu";
+		compatible = "ingenic,x1000-cgu", "simple-mfd";
 		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
 
 		#clock-cells = <1>;
 
 		clocks = <&exclk>, <&rtclk>;
 		clock-names = "ext", "rtc";
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,x1000-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu X1000_CLK_OTGPHY>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		rng: rng@d8 {
+			compatible = "ingenic,x1000-rng";
+			reg = <0xd8 0x8>;
+
+			status = "disabled";
+		};
+	};
+
+	ost: timer@12000000 {
+		compatible = "ingenic,x1000-ost";
+		reg = <0x12000000 0x3c>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1000_CLK_OST>;
+		clock-names = "ost";
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <3>;
 	};
 
 	tcu: timer@10002000 {
@@ -323,4 +357,24 @@ 
 			status = "disabled";
 		};
 	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,x1000-otg", "snps,dwc2";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu X1000_CLK_OTG>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
 };
diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
index b05dac3ae308..b21c93057356 100644
--- a/arch/mips/boot/dts/ingenic/x1830.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
@@ -52,13 +52,40 @@ 
 	};
 
 	cgu: x1830-cgu@10000000 {
-		compatible = "ingenic,x1830-cgu";
+		compatible = "ingenic,x1830-cgu", "simple-mfd";
 		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
 
 		#clock-cells = <1>;
 
 		clocks = <&exclk>, <&rtclk>;
 		clock-names = "ext", "rtc";
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,x1830-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu X1830_CLK_OTGPHY>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	ost: timer@12000000 {
+		compatible = "ingenic,x1830-ost", "ingenic,x1000-ost";
+		reg = <0x12000000 0x3c>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1830_CLK_OST>;
+		clock-names = "ost";
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <4>;
 	};
 
 	tcu: timer@10002000 {
@@ -236,6 +263,15 @@ 
 		status = "disabled";
 	};
 
+	dtrng: trng@10072000 {
+		compatible = "ingenic,x1830-dtrng";
+		reg = <0x10072000 0xc>;
+
+		clocks = <&cgu X1830_CLK_DTRNG>;
+
+		status = "disabled";
+	};
+
 	pdma: dma-controller@13420000 {
 		compatible = "ingenic,x1830-dma";
 		reg = <0x13420000 0x400
@@ -311,4 +347,24 @@ 
 			status = "disabled";
 		};
 	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,x1830-otg", "snps,dwc2";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu X1830_CLK_OTG>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
 };