diff mbox series

[5.4,85/85] arm64: dts: marvell: espressobin: Add ethernet switch aliases

Message ID 20201109125026.670807503@linuxfoundation.org
State New
Headers show
Series None | expand

Commit Message

Greg KH Nov. 9, 2020, 12:56 p.m. UTC 
From: Pali Rohár <pali@kernel.org>

commit b64d814257b027e29a474bcd660f6372490138c7 upstream.

Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.

Since commit a2c7023f7075c ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.

Currently Espressobin DTS file contains alias just for ethernet0.

This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.

DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).

Fixes: 5253cb8c00a6f ("arm64: dts: marvell: espressobin: add ethernet alias")
Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported Espressobin rev V5 changes to 5.4 and 4.19 versions]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts |   12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
diff mbox series

Patch

--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
@@ -21,6 +21,10 @@ 
 
 	aliases {
 		ethernet0 = &eth0;
+		/* for dsa slave device */
+		ethernet1 = &switch0port1;
+		ethernet2 = &switch0port2;
+		ethernet3 = &switch0port3;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -147,7 +151,7 @@ 
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			switch0port0: port@0 {
 				reg = <0>;
 				label = "cpu";
 				ethernet = <&eth0>;
@@ -158,19 +162,19 @@ 
 				};
 			};
 
-			port@1 {
+			switch0port1: port@1 {
 				reg = <1>;
 				label = "wan";
 				phy-handle = <&switch0phy0>;
 			};
 
-			port@2 {
+			switch0port2: port@2 {
 				reg = <2>;
 				label = "lan0";
 				phy-handle = <&switch0phy1>;
 			};
 
-			port@3 {
+			switch0port3: port@3 {
 				reg = <3>;
 				label = "lan1";
 				phy-handle = <&switch0phy2>;