@@ -1591,6 +1591,13 @@
};
};
+ stusb1600_pins_a: stusb1600-0 {
+ pins {
+ pinmux = <STM32_PINMUX('I', 11, ANALOG)>;
+ bias-pull-up;
+ };
+ };
+
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
@@ -238,6 +238,30 @@
/delete-property/dmas;
/delete-property/dma-names;
+ stusb1600@28 {
+ compatible = "st,stusb1600";
+ reg = <0x28>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpioi>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&stusb1600_pins_a>;
+ status = "okay";
+ vdd-supply = <&vin>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ typec-power-opmode = "default";
+
+ port {
+ con_usbotg_hs_ep: endpoint {
+ remote-endpoint = <&usbotg_hs_ep>;
+ };
+ };
+ };
+ };
+
pmic: stpmic@33 {
compatible = "st,stpmic1";
reg = <0x33>;
@@ -648,6 +672,12 @@
phy-names = "usb2-phy";
usb-role-switch;
status = "okay";
+
+ port {
+ usbotg_hs_ep: endpoint {
+ remote-endpoint = <&con_usbotg_hs_ep>;
+ };
+ };
};
&usbphyc {
This patch adds support for STUSB1600 USB Type-C port controller, used on I2C4 on stm32mp15xx-dkx. The default configuration on this board, on Type-C connector, is: - Dual Power Role (DRP), so set power-role to "dual"; - Vbus limited to 500mA, so set typec-power-opmode to "default" (it means 500mA in USB 2.0). typec-power-opmode is used to reconfigure the STUSB1600 advertising of current capability when its NVM is not in line with the board layout. On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN. So power operation mode depends on the power supply used. To avoid any power issues, it is better to limit Vbus to 500mA on this board. ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and signal is active low. USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx boards, so disconnection are not detected. Without DWC2 usb-role-switch: - if you unplug the USB cable from the Type-C port, you have to manually disconnect the USB gadget: echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect - Then you can plug the USB cable again in the Type-C port, and manually reconnect the USB gadget: echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> --- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 7 ++++++ arch/arm/boot/dts/stm32mp15xx-dkx.dtsi | 30 ++++++++++++++++++++++++ 2 files changed, 37 insertions(+)