new file mode 100644
@@ -0,0 +1,151 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC ADC Thermal Monitoring
+maintainers:
+ - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+
+properties:
+ compatible:
+ const: qcom,spmi-adc-tm5
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ "#thermal-sensor-cells":
+ const: 1
+ description:
+ Number of cells required to uniquely identify the thermal sensors. Since
+ we have multiple sensors this is set to 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ qcom,avg-samples:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Number of samples to be used for measurement.
+ enum:
+ - 1
+ - 2
+ - 4
+ - 8
+ - 16
+ default: 1
+
+ qcom,decimation:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: This parameter is used to decrease ADC sampling rate.
+ Quicker measurements can be made by reducing decimation ratio.
+ enum:
+ - 250
+ - 420
+ - 840
+ default: 840
+
+patternProperties:
+ "^([-a-z0-9]*)@[0-9]+$":
+ type: object
+ description:
+ Represent one thermal sensor.
+
+ properties:
+ reg:
+ description: Specify the sensor channel.
+ maxItems: 1
+
+ io-channels:
+ description:
+ From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor
+
+ qcom,adc-channel:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Corresponding ADC channel ID.
+
+ qcom,ratiometric:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Channel calibration type.
+ If this property is specified VADC will use the VDD reference
+ (1.875V) and GND for channel calibration. If property is not found,
+ channel will be calibrated with 0V and 1.25V reference channels,
+ also known as absolute calibration.
+
+ qcom,hw-settle-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Time between AMUX getting configured and the ADC starting conversion.
+
+ qcom,pre-scaling:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Used for scaling the channel input signal before the
+ signal is fed to VADC. See qcom,spi-vadc specification for the list
+ of possible values.
+ minItems: 2
+ maxItems: 2
+
+ required:
+ - reg
+ - qcom,adc-channel
+
+ additionalProperties:
+ false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - "#address-cells"
+ - "#size-cells"
+ - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/iio/qcom,spmi-vadc.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spmi_bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pm8150b_adc: adc@3100 {
+ reg = <0x3100>;
+ compatible = "qcom,spmi-adc5";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+
+ /* Other propreties are omitted */
+ conn-therm@4f {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+ };
+
+ pm8150b_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ conn-therm@0 {
+ reg = <0>;
+ io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
+ qcom,adc-channel = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+ };
+ };
+...