diff mbox series

[5/8] ath11k: disable monitor mode on QCA6390

Message ID 1601399736-3210-6-git-send-email-kvalo@codeaurora.org
State New
Headers show
Series None | expand

Commit Message

Kalle Valo Sept. 29, 2020, 5:15 p.m. UTC
QCA6390 does not support monitor mode at the moment so disable it altogether,
using a hack as mac80211 does not support disabling it otherwise. Add a boolean
to hw_params to know if hardware supports monitor mode.

IPQ8074 continues to support monitor mode normally.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/core.c | 3 +++
 drivers/net/wireless/ath/ath11k/hw.h   | 1 +
 drivers/net/wireless/ath/ath11k/mac.c  | 8 ++++++++
 3 files changed, 12 insertions(+)
diff mbox series

Patch

diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
index 28aeb9fe602b..951dca1b66b4 100644
--- a/drivers/net/wireless/ath/ath11k/core.c
+++ b/drivers/net/wireless/ath/ath11k/core.c
@@ -62,6 +62,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
 					BIT(NL80211_IFTYPE_AP) |
 					BIT(NL80211_IFTYPE_MESH_POINT),
+		.supports_monitor = true,
 	},
 	{
 		.hw_rev = ATH11K_HW_IPQ6018_HW10,
@@ -96,6 +97,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
 					BIT(NL80211_IFTYPE_AP) |
 					BIT(NL80211_IFTYPE_MESH_POINT),
+		.supports_monitor = true,
 	},
 	{
 		.name = "qca6390 hw2.0",
@@ -129,6 +131,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 
 		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
 					BIT(NL80211_IFTYPE_AP),
+		.supports_monitor = false,
 	},
 };
 
diff --git a/drivers/net/wireless/ath/ath11k/hw.h b/drivers/net/wireless/ath/ath11k/hw.h
index 5bd3fe618dd8..a281ad3bdf04 100644
--- a/drivers/net/wireless/ath/ath11k/hw.h
+++ b/drivers/net/wireless/ath/ath11k/hw.h
@@ -158,6 +158,7 @@  struct ath11k_hw_params {
 	u8 spectral_fft_sz;
 
 	u16 interface_modes;
+	bool supports_monitor;
 };
 
 struct ath11k_hw_ops {
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 491e62d66edc..9efaf6e7aacf 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -6241,6 +6241,14 @@  static int __ath11k_mac_register(struct ath11k *ar)
 		goto err_free_if_combs;
 	}
 
+	if (!ab->hw_params.supports_monitor)
+		/* There's a race between calling ieee80211_register_hw()
+		 * and here where the monitor mode is enabled for a little
+		 * while. But that time is so short and in practise it make
+		 * a difference in real life.
+		 */
+		ar->hw->wiphy->interface_modes &= ~BIT(NL80211_IFTYPE_MONITOR);
+
 	/* Apply the regd received during initialization */
 	ret = ath11k_regd_update(ar, true);
 	if (ret) {