@@ -258,6 +258,22 @@ F: arch/arm/mach-at91/
F: board/atmel/
F: drivers/misc/microchip_flexcom.c
+ARM NEXELL S5P4418
+M: Stefan Bosch <stefan_b at posteo.net>
+S: Maintained
+F: arch/arm/cpu/armv7/s5p4418/
+F: arch/arm/dts/s5p4418*
+F: arch/arm/mach-nexell/
+F: board/friendlyarm/
+F: configs/s5p4418_nanopi2_defconfig
+F: doc/README.s5p4418
+F: drivers/gpio/nx_gpio.c
+F: drivers/i2c/nx_i2c.c
+F: drivers/mmc/nexell_dw_mmc_dm.c
+F: drivers/video/nexell/
+F: drivers/video/nexell_display.c
+F: include/configs/s5p4418_nanopi2.h
+
ARM OWL
M: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
S: Maintained
new file mode 100644
@@ -0,0 +1,148 @@
+CONFIG_ARM=y
+CONFIG_ARCH_NEXELL=y
+CONFIG_ARCH_S5P4418=y
+CONFIG_TARGET_NANOPI2=y
+CONFIG_DM_I2C=y
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="s5p4418-nanopi2"
+CONFIG_FIT=y
+
+# Must be set to 'n' (apparently "CONFIG_EFI_LOADER=y" per default)
+# otherwise boot errors "efi_runtime_relocate: Unknown relocation type 0"
+CONFIG_EFI_LOADER=n
+
+CONFIG_CMD_MEMTEST=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_NET is not set
+
+# Default is CONFIG_NET=y, in this case:
+# Loading Environment from MMC... ## Warning: Unknown environment variable type 'm'
+# OK
+# CONFIG_CMD_NET=y must be set to avoid this Warning. But then:
+# Net: Net Initialization Skipped
+# No ethernet found.
+# If CONFIG_NET=n is set additionally warning at "make s5p4418_nanopi2_defconfig":
+# arch/../configs/s5p4418_nanopi2_defconfig:24:warning: override: reassigning to symbol CMD_NET
+#
+# --> CONFIG_NET=n set only
+CONFIG_NET=n
+
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_FDISK=y
+CONFIG_CMD_EXT4_IMG_WRITE=y
+CONFIG_CMD_SD_RECOVERY=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_NEXELL=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_AXP228=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_AXP228=y
+CONFIG_DM_PWM=n
+
+CONFIG_DISPLAY=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_CONSOLE_BG_COL=0xff
+CONFIG_SYS_CONSOLE_FG_COL=0x00
+CONFIG_VIDEO_NX=y
+CONFIG_VIDEO_NX_RGB=y
+CONFIG_VIDEO_NX_LVDS=y
+
+CONFIG_VIDEO_NX_HDMI=y
+
+CONFIG_REGEX=y
+CONFIG_ERRNO_STR=y
+
+CONFIG_SYS_TEXT_BASE=0x74C00000
+CONFIG_SYS_RESERVE_MEM_SIZE=0x00400000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SYS_CACHELINE_SIZE=64
+
+## System initialize options (board_init_f)
+# board_init_f->init_sequence, call board_early_init_f
+CONFIG_BOARD_LATE_INIT=y
+# board_init_f->init_sequence, call print_cpuinfo
+CONFIG_DISPLAY_CPUINFO=y
+# board_init_f->init_sequence, call show_board_info
+CONFIG_DISPLAY_BOARDINFO=y
+# board_init_f, CONFIG_SYS_ICACHE_OFF
+CONFIG_SYS_DCACHE_OFF=y
+# board_init_r, call arch_misc_init
+CONFIG_ARCH_MISC_INIT=y
+
+CONFIG_BOOTDELAY=1
+CONFIG_ZERO_BOOTDELAY_CHECK=y
+
+## U-Boot Environments
+## refer to common/env_common.c
+
+# CONFIG_ENV_IS_IN_MMC must be set here and not in s5p4418_nanopi2.h
+# otherwise CONFIG_ENV_IS_NOWHERE is set by env/Kconfig and environment
+# (bootargs) are not loaded
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_OFFSET=0x2E0200
+CONFIG_ENV_SIZE=0x4000
+CONFIG_CMD_SAVEENV=y
+
+## Etc Command definition
+# image info
+CONFIG_CMD_IMI=y
+# add command line history
+CONFIG_CMDLINE_EDITING=y
+CONFIG_INITRD_TAG=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_REVISION_TAG=y
+CONFIG_CMD_BOOTZ=y
+
+## serial console configuration
+CONFIG_CONS_INDEX=0
+CONFIG_BAUDRATE=115200
+
+## SD/MMC
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_GENERIC_MMC=y
+CONFIG_MMC=y
+CONFIG_MMC_DW=y
+CONFIG_NEXELL_DWMMC=y
+CONFIG_CMD_MMC=y
+CONFIG_DM_MMC=y
+
+CONFIG_DOS_PARTITION=y
+CONFIG_CMD_FAT=y
+CONFIG_FS_FAT=y
+CONFIG_FAT_WRITE=y
+
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_FS_EXT4=y
+CONFIG_EXT4_WRITE=y
+
+## OF_CONTROL
+CONFIG_FIT_BEST_MATCH=y
+CONFIG_OF_LIBFDT=y
+CONFIG_OF_BOARD_SETUP=y
+
+## BOOTCOMMAND
+CONFIG_ROOT_DEV=1
+CONFIG_BOOT_PART=1
+CONFIG_ROOT_PART=2
+
+## Misc.
+CONFIG_S5P4418_ONEWIRE=y
+CONFIG_PWM_NX=y
+
+# necessary for if-cmd
+CONFIG_HUSH_PARSER=y
+
+# set to 'n' to save memory
+CONFIG_SYS_LONGHELP=y
+
+# uncomment for debugging (trace) of MMC-CMDs
+#CONFIG_MMC_TRACE=y
new file mode 100644
@@ -0,0 +1,63 @@
+
+Summary
+=======
+
+This README is about U-Boot support for SAMSUNG's/NEXELL's ARM Cortex-A9 based
+S5P4418 SoC. It is based on FriendlyARM's U-Boot v2016.01 for the NanoPi2
+(and other) boards [1].
+
+Currently the following boards are supported:
+
+* FriendlyArm NanoPi2 [2]
+* FriendlyArm NanoPC-T2 [3]
+
+
+Build
+=====
+
+* NanoPi2 and NanoPC-T2
+
+make s5p4418_nanopi2_defconfig
+make
+
+
+Installation
+============
+
+- Download Official-ROMs-SDCard-20190718.7z from [4] (images files for android,
+ friendlyCore and LUbuntu)
+- Use s5p4418-sd-lubuntu-desktop-xenial-4.4-armhf-20190718.img to make a SD-card
+- Use dd in the directory where U-Boot has been built to update U-Boot:
+ (replace <SD-card> with the device used for the SD-card, e.g. sdc)
+ sudo dd seek=3841 if=u-boot.bin of=/dev/<SD-card>
+- Boot the board from this SD-card
+
+The source code for (the used?) LUbuntu 16.04 can be found at [5].
+
+
+Links
+=====
+
+[1] FriendlyArm U-boot v2016.01:
+
+https://github.com/friendlyarm/u-boot/tree/nanopi2-v2016.01
+
+
+[2] NanoPi2:
+
+http://wiki.friendlyarm.com/wiki/index.php/NanoPi_2
+
+
+[3] NanoPC-T2:
+
+http://wiki.friendlyarm.com/wiki/index.php/NanoPC-T2
+
+
+[4] FriendlyArm image files for NanoPi2:
+
+http://download.friendlyarm.com//NanoPi2
+
+
+[5] FriendlyArm LUbuntu 16.04 Source Code for NanoPi2:
+
+https://github.com/friendlyarm/linux/tree/nanopi2-v4.4.y
new file mode 100644
@@ -0,0 +1,265 @@
+/* SPDX-License-Identifier: GPL-2.0+
+ *
+ * Copyright (C) Guangzhou FriendlyARM Computer Tech. Co., Ltd.
+ * (http://www.friendlyarm.com)
+ *
+ * (C) Copyright 2016 Nexell
+ * Hyejung Kwon <cjscld15 at nexell.co.kr>
+ *
+ * Copyright (C) 2019 Stefan Bosch <stefan_b at posteo.net>
+ */
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+#include <linux/sizes.h>
+#include <asm/arch/nexell.h>
+
+/*-----------------------------------------------------------------------
+ * System memory Configuration
+ */
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MEM_SIZE 0x40000000
+#define CONFIG_SYS_SDRAM_BASE 0x71000000
+
+/*
+ * "(CONFIG_SYS_MEM_SIZE - CONFIG_SYS_RESERVE_MEM_SIZE)" has been used in
+ * u-boot nanopi2-v2016.01.
+ * This is not working anymore because boot_fdt_add_mem_rsv_regions() in
+ * common/image-fdt.c has been extended:
+ * Also reserved-memory sections are marked as unusable.
+ *
+ * In friendlyArm Ubuntu 16.04 source arch/arm/boot/dts/s5p4418.dtsi:
+ * reserved-memory {
+ * #address-cells = <1>;
+ * #size-cells = <1>;
+ * ranges;
+ *
+ * secure_memory at b0000000 {
+ * reg = <0xB0000000 0x1000000>;
+ * nop-map;
+ * };
+ * };
+ *
+ * arch_lmb_reserve() of arch/arm/lib/bootm.c:
+ * "Allocate space for command line and board info - ... below the current
+ * stack pointer."
+ * --> Memory allocated would overlap with "secure_memory at b0000000"
+ * --> lmb_add_region(rgn, base==0xb0000000, size==0x1000000) fails,
+ * boot output:
+ * ...
+ * Kernel image @ 0x71080000 [ 0x000000 - 0x60e628 ]
+ * ## Flattened Device Tree blob at 7a000000
+ * Booting using the fdt blob at 0x7a000000
+ * ERROR: reserving fdt memory region failed (addr=b0000000 size=1000000)
+ * Using Device Tree in place at 7a000000, end 7a00fbf0
+ *
+ * Starting kernel ...
+ * ...
+ */
+#define CONFIG_SYS_SDRAM_SIZE (0xb0000000 - CONFIG_SYS_SDRAM_BASE)
+
+#define CONFIG_SYS_MALLOC_LEN (32 * 1024 * 1024)
+
+#define BMP_LOAD_ADDR 0x78000000
+
+/* kernel load address */
+#define CONFIG_SYS_LOAD_ADDR 0x71080000
+#define INITRD_START 0x79000000
+#define KERNEL_DTB_ADDR 0x7A000000
+
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END ((ulong)CONFIG_SYS_SDRAM_BASE + \
+ (ulong)CONFIG_SYS_SDRAM_SIZE)
+
+/*-----------------------------------------------------------------------
+ * High Level System Configuration
+ */
+/* Not used: not need IRQ/FIQ stuff */
+#undef CONFIG_USE_IRQ
+/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_HZ 1000
+
+/*-----------------------------------------------------------------------
+ * System initialize options (board_init_f)
+ */
+/* board_init_f->init_sequence, call arch_cpu_init */
+#define CONFIG_ARCH_CPU_INIT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+#ifdef CONFIG_SYS_PROMPT
+#undef CONFIG_SYS_PROMPT
+/* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "nanopi2# "
+#endif
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+/* max number of command args */
+#define CONFIG_SYS_MAXARGS 16
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/*-----------------------------------------------------------------------
+ * allow to overwrite serial and ethaddr
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*-----------------------------------------------------------------------
+ * Etc Command definition
+ */
+#define CONFIG_CMDLINE_TAG /* use bootargs commandline */
+
+#undef CONFIG_BOOTM_NETBSD
+#undef CONFIG_BOOTM_RTEMS
+
+/*-----------------------------------------------------------------------
+ * serial console configuration
+ */
+#define CONFIG_PL011_CLOCK 50000000
+#define CONFIG_PL01x_PORTS {(void *)PHY_BASEADDR_UART0, \
+ (void *)PHY_BASEADDR_UART1, \
+ (void *)PHY_BASEADDR_UART2, \
+ (void *)PHY_BASEADDR_UART3}
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * PLL
+ */
+#define CONFIG_SYS_PLLFIN 24000000UL
+
+/*-----------------------------------------------------------------------
+ * Timer
+ */
+#define CONFIG_TIMER_SYS_TICK_CH 0
+
+/*-----------------------------------------------------------------------
+ * BACKLIGHT
+ */
+#ifndef CONFIG_S5P4418_ONEWIRE
+/* fallback to pwm */
+#define BACKLIGHT_CH 0
+#define BACKLIGHT_DIV 0
+#define BACKLIGHT_INV 0
+#define BACKLIGHT_DUTY 50
+#define BACKLIGHT_HZ 1000
+#endif
+
+/*-----------------------------------------------------------------------
+ * SD/MMC
+ */
+#if defined(CONFIG_MMC)
+/* eMMC = 0, SD-card = 2 */
+#define CONFIG_SYS_MMC_DEV 2
+#define CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_DEV
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * Default environment organization
+ */
+#if !defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_IS_IN_NAND) && \
+ !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_EEPROM)
+ /* default: CONFIG_ENV_IS_NOWHERE */
+ #define CONFIG_ENV_IS_NOWHERE
+ #define CONFIG_ENV_OFFSET 1024
+ #define CONFIG_ENV_SIZE (4 * 1024) /* env size */
+ /* imls - list all images found in flash, default enable so disable */
+ #undef CONFIG_CMD_IMLS
+#endif
+
+/*-----------------------------------------------------------------------
+ * VIDEO
+ */
+
+#define CONFIG_VIDEO_LOGO
+
+#define CONFIG_SPLASH_SCREEN
+
+#ifdef CONFIG_VIDEO_LOGO
+#define CONFIG_CMD_BMP
+
+#ifdef CONFIG_DM_VIDEO
+#define CONFIG_BMP_24BPP
+#endif
+
+#ifdef CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SOURCE 1
+#define CONFIG_SPLASH_SCREEN_ALIGN 1
+#define SPLASH_FILE logo.bmp
+#endif
+#endif
+
+/*-----------------------------------------------------------------------
+ * ENV
+ */
+#define BLOADER_MMC \
+ "ext4load mmc ${rootdev}:${bootpart} "
+
+#ifdef CONFIG_OF_BOARD_SETUP
+#define EXTRA_ENV_DTB_RESERVE \
+ "dtb_reserve=" \
+ "if test -n \"$dtb_addr\"; then fdt addr $dtb_addr; fi\0"
+#else
+#define EXTRA_ENV_DTB_RESERVE \
+ "dtb_reserve=" \
+ "if test -n \"$fb_addr\"; then " \
+ "fdt addr $dtb_addr;" \
+ "fdt resize;" \
+ "fdt mk /reserved-memory display_reserved;" \
+ "fdt set /reserved-memory/display_reserved " \
+ "reg <$fb_addr 0x800000>;" \
+ "fi;\0"
+#endif
+
+#ifdef CONFIG_SPLASH_SCREEN
+#define EXTRA_ENV_BOOT_LOGO \
+ "splashimage=" __stringify(BMP_LOAD_ADDR)"\0" \
+ "splashfile=" __stringify(SPLASH_FILE)"\0" \
+ "splashpos=m,m\0" \
+ "fb_addr=\0" \
+ EXTRA_ENV_DTB_RESERVE
+#else
+ #define EXTRA_ENV_BOOT_LOGO EXTRA_ENV_DTB_RESERVE
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "rootdev=" __stringify(CONFIG_ROOT_DEV) "\0" \
+ "rootpart=" __stringify(CONFIG_ROOT_PART) "\0" \
+ "bootpart=" __stringify(CONFIG_BOOT_PART) "\0" \
+ "kernel=zImage\0" \
+ "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "dtb_name=s5p4418-nanopi2-rev01.dtb\0" \
+ "dtb_addr=" __stringify(KERNEL_DTB_ADDR) "\0" \
+ "initrd_name=ramdisk.img\0" \
+ "initrd_addr=" __stringify(INITRD_START) "\0" \
+ "initrd_size=0x600000\0" \
+ "load_dtb=" \
+ BLOADER_MMC "${dtb_addr} ${dtb_name}; " \
+ "run dtb_reserve\0" \
+ "load_kernel=" \
+ BLOADER_MMC "${loadaddr} ${kernel}\0" \
+ "load_initrd=" \
+ BLOADER_MMC "${initrd_addr} ${initrd_name}; " \
+ "setenv initrd_size 0x${filesize}\0" \
+ "mmcboot=" \
+ "run load_kernel; run load_initrd; run load_dtb; " \
+ "bootz ${loadaddr} ${initrd_addr}:${initrd_size} " \
+ "${dtb_addr}\0" \
+ "bootcmd=run mmcboot\0" \
+ EXTRA_ENV_BOOT_LOGO
+
+#endif /* __CONFIG_H__ */
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01: - Configuration changed, mainly several "CONFIG_..." moved from s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related configs removed because USB is not supported yet. - s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2 specific defines because the appropriate values do not need to be configurable. Signed-off-by: Stefan Bosch <stefan_b at posteo.net> --- Changes in v2: - USB related configs removed because USB is not supported yet. - CONFIG_CMD_MEMTEST moved from s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig. - MAINTAINERS: "F: drivers/pwm/pwm-nexell*" deleted because arch/arm/cpu/armv7/s5p-common/pwm.c is used now. Furthermore double line "F: drivers/video/nexell/" deleted. MAINTAINERS | 16 +++ configs/s5p4418_nanopi2_defconfig | 148 +++++++++++++++++++++ doc/README.s5p4418 | 63 +++++++++ include/configs/s5p4418_nanopi2.h | 265 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 492 insertions(+) create mode 100644 configs/s5p4418_nanopi2_defconfig create mode 100644 doc/README.s5p4418 create mode 100644 include/configs/s5p4418_nanopi2.h