diff mbox series

[v4,04/12] arm: mvebu: clearfog: initial ClearFog Base variant

Message ID 20200126225009.7362-5-mrjoel@lixil.net
State New
Headers show
Series ClearFog Base static variant support | expand

Commit Message

Joel Johnson Jan. 26, 2020, 10:50 p.m. UTC
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.

Signed-off-by: Joel Johnson <mrjoel at lixil.net>

---

v2 changes:
  - reworked based on Baruch's run-time TLV EEPROM detection series
v3 changes:
  - rebased on mvebu merged run-time TLV EEPROM detection series
  - minor update to help test regarding runtime detection failures
v4 changes:
  - use runtime static config adjust instead of #ifdef in cases where
    hardware EEPROM detection fails or is disabled in build
    SPL size change for defconfig increases 36 bytes (122893 to 122929)
    SPL size change for defconfig+Base increases 60 bytes (122893 to 122953)
  - add placeholder support for EEPROM based Clearfog Pro, based on
    initial name confirmation from Baruch. I wanted to include the check
    at least in the patch for review to indicate expected usage to
    ensure that a Clearfog Pro EEPROM device boots correctly even if the
    image is built with Base static configuration. If there are other
    prerelease concerns and this should be added separately later, I'd
    be fine with that too.
  - Note that this approach *does not* currently provide any mechanism
    for EEPROM detected boards to have their SFP speed changed or switch
    between PCIE/SATA signalling. I'm assuming that will be done based on
    hardware detection, but confirmation/acceptance in review would be
    appreciated so it can be revisited if needed.

---
 arch/arm/mach-mvebu/Kconfig        |  2 ++
 board/solidrun/clearfog/Kconfig    | 18 ++++++++++++++++++
 board/solidrun/clearfog/clearfog.c | 25 ++++++++++++++++++++++---
 3 files changed, 42 insertions(+), 3 deletions(-)
 create mode 100644 board/solidrun/clearfog/Kconfig
diff mbox series

Patch

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index bc5eaa5a76..161dee937f 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -280,4 +280,6 @@  config SECURED_MODE_CSK_INDEX
 	default 0
 	depends on SECURED_MODE_IMAGE
 
+source "board/solidrun/clearfog/Kconfig"
+
 endif
diff --git a/board/solidrun/clearfog/Kconfig b/board/solidrun/clearfog/Kconfig
new file mode 100644
index 0000000000..936d5918f8
--- /dev/null
+++ b/board/solidrun/clearfog/Kconfig
@@ -0,0 +1,18 @@ 
+menu "ClearFog configuration"
+	depends on TARGET_CLEARFOG
+
+config TARGET_CLEARFOG_BASE
+	bool "Use ClearFog Base static configuration"
+	help
+	  Use the ClearFog Base as the static configuration instead of the
+	  default which uses the ClearFog Pro.
+
+	  Runtime board detection is always attempted and used if available. The
+	  static configuration is used as a fallback in cases where runtime
+	  detection is disabled, is not available in hardware, or otherwise fails.
+
+	  Only newer revisions of the ClearFog product line support runtime
+	  detection via additional EEPROM hardware. This option enables selecting
+	  the Base variant for older hardware revisions.
+
+endmenu
diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c
index 9b31902c70..04238d2b05 100644
--- a/board/solidrun/clearfog/clearfog.c
+++ b/board/solidrun/clearfog/clearfog.c
@@ -42,6 +42,7 @@  static void cf_read_tlv_data(void)
 	read_tlv_data(&cf_tlv_data);
 }
 
+/* The starting board_serdes_map reflects original Clearfog Pro usage */
 static struct serdes_map board_serdes_map[] = {
 	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
@@ -51,6 +52,15 @@  static struct serdes_map board_serdes_map[] = {
 	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 };
 
+void config_static_serdes_map(void)
+{
+	if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		board_serdes_map[4].serdes_type = USB3_HOST0;
+		board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
+		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+	}
+}
+
 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 {
 	cf_read_tlv_data();
@@ -59,12 +69,17 @@  int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 		board_serdes_map[0].serdes_type = PEX0;
 		board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
 		board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
-	}
-
-	if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
+		/* handle recognized product as noop, no adjustment required */
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
 		board_serdes_map[4].serdes_type = USB3_HOST0;
 		board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
 		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+	} else {
+		/* fallback to static default since runtime detection failed,
+		 * either EEPROM not being available or unrecognized product
+		 */
+		config_static_serdes_map();
 	}
 
 	*serdes_map_array = board_serdes_map;
@@ -171,6 +186,8 @@  int board_init(void)
 int checkboard(void)
 {
 	char *board = "Clearfog Pro";
+	if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
+		board = "Clearfog Base";
 
 	cf_read_tlv_data();
 	if (strlen(cf_tlv_data.tlv_product_name[0]) > 0)
@@ -200,6 +217,8 @@  int board_late_init(void)
 		env_set("fdtfile", "armada-385-clearfog-gtr-s4.dtb");
 	else if (sr_product_is(&cf_tlv_data, "Clearfog GTR L8"))
 		env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb");
+	else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
+		env_set("fdtfile", "armada-388-clearfog-base.dtb");
 
 	return 0;
 }