[v4,4/6] board: tbs2910: enable CONFIG_DISTRO_DEFAULTS

The side effect is that it increase the size of the
resultimg image, which is already very close to the
size limit.

With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
increase:
- text: 8744 bytes
- data: 132 bytes
- bss: 60 bytes
- total: 8936 bytes

Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo at cyberdimension.org>
---
 configs/tbs2910_defconfig | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)

On 27.02.20 01:37, Denis 'GNUtoo' Carikli wrote:
> The side effect is that it increase the size of the
> resultimg image, which is already very close to the
> size limit.
Please also mention the main purpose, preparation for distro_boot
support, not only the side effect of this patch.
>
> With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
> GNU/Linux distribution, we have the following size
> increase:
> - text: 8744 bytes
> - data: 132 bytes
> - bss: 60 bytes
> - total: 8936 bytes
>
> Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo at cyberdimension.org>
I hoped you would enable CONFIG_CMD_SYSBOOT instead of enabling
CONFIG_DISTRO_DEFAULTS with associated defconfig cleanup, as discussed
for v3 of this patch. This would save ~1.4k of image size without
reducing functionality. A possible split out of PXE support from
DISTRO_DEFAULTS should be done as separate independent patch series (as
suggested by Tom Rini), since this affects more boards, needs more
discussions and review, and would unnecessarily delay the SYSBOOT
support for tbs2910 if done in the same series.

Thanks,
Soeren
> ---
>  configs/tbs2910_defconfig | 16 ++--------------
>  1 file changed, 2 insertions(+), 14 deletions(-)
>
> diff --git a/configs/tbs2910_defconfig b/configs/tbs2910_defconfig
> index 5603bef64e..1cf09bb741 100644
> --- a/configs/tbs2910_defconfig
> +++ b/configs/tbs2910_defconfig
> @@ -9,18 +9,15 @@ CONFIG_NR_DRAM_BANKS=1
>  CONFIG_PRE_CON_BUF_ADDR=0x7c000000
>  CONFIG_CMD_HDMIDETECT=y
>  CONFIG_AHCI=y
> +CONFIG_DISTRO_DEFAULTS=y
>  CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTCOMMAND=y
>  CONFIG_BOOTCOMMAND="mmc rescan; if run bootcmd_up1; then run bootcmd_up2; else run bootcmd_mmc; fi"
>  CONFIG_USE_PREBOOT=y
>  CONFIG_PREBOOT="echo PCI:; pci enum; pci 1; usb start; if hdmidet; then run set_con_hdmi; else run set_con_serial; fi"
>  CONFIG_PRE_CONSOLE_BUFFER=y
> -CONFIG_SUPPORT_RAW_INITRD=y
>  CONFIG_BOUNCE_BUFFER=y
>  CONFIG_BOARD_EARLY_INIT_F=y
> -CONFIG_HUSH_PARSER=y
>  CONFIG_SYS_PROMPT="Matrix U-Boot> "
> -CONFIG_CMD_BOOTZ=y
>  # CONFIG_BOOTM_PLAN9 is not set
>  # CONFIG_BOOTM_RTEMS is not set
>  # CONFIG_BOOTM_VXWORKS is not set
> @@ -31,22 +28,14 @@ CONFIG_CMD_I2C=y
>  # CONFIG_CMD_LOADB is not set
>  # CONFIG_CMD_LOADS is not set
>  CONFIG_CMD_MMC=y
> -CONFIG_CMD_PART=y
>  CONFIG_CMD_PCI=y
>  CONFIG_CMD_SATA=y
>  CONFIG_CMD_USB=y
>  CONFIG_CMD_USB_MASS_STORAGE=y
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
>  CONFIG_CMD_CACHE=y
>  CONFIG_CMD_TIME=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_EXT4=y
>  CONFIG_CMD_EXT4_WRITE=y
> -CONFIG_CMD_FAT=y
> -CONFIG_CMD_FS_GENERIC=y
> -CONFIG_EFI_PARTITION=y
> +# CONFIG_ISO_PARTITION is not set
>  CONFIG_OF_CONTROL=y
>  CONFIG_OF_EMBED=y
>  CONFIG_DEFAULT_DEVICE_TREE="imx6q-tbs2910"
> @@ -76,7 +65,6 @@ CONFIG_RTC_DS1307=y
>  CONFIG_DM_THERMAL=y
>  CONFIG_USB=y
>  CONFIG_DM_USB=y
> -CONFIG_USB_STORAGE=y
>  CONFIG_USB_KEYBOARD=y
>  CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
>  CONFIG_USB_GADGET=y