@@ -651,6 +651,7 @@ struct mlx5e_rq {
struct {
u16 umem_headroom;
u16 headroom;
+ u32 first_frame_sz;
u8 map_dir; /* dma map direction */
} buff;
@@ -137,6 +137,7 @@ bool mlx5e_xdp_handle(struct mlx5e_rq *rq, struct mlx5e_dma_info *di,
if (xsk)
xdp.handle = di->xsk.handle;
xdp.rxq = &rq->xdp_rxq;
+ xdp.frame_sz = rq->buff.first_frame_sz;
act = bpf_prog_run_xdp(prog, &xdp);
if (xsk) {
@@ -462,6 +462,8 @@ static int mlx5e_alloc_rq(struct mlx5e_channel *c,
rq->mpwqe.num_strides =
BIT(mlx5e_mpwqe_get_log_num_strides(mdev, params, xsk));
+ rq->buff.first_frame_sz = (1 << rq->mpwqe.log_stride_sz);
+
err = mlx5e_create_rq_umr_mkey(mdev, rq);
if (err)
goto err_rq_wq_destroy;
@@ -485,6 +487,8 @@ static int mlx5e_alloc_rq(struct mlx5e_channel *c,
num_xsk_frames = wq_sz << rq->wqe.info.log_num_frags;
rq->wqe.info = rqp->frags_info;
+ rq->buff.first_frame_sz = rq->wqe.info.arr[0].frag_stride;
+
rq->wqe.frags =
kvzalloc_node(array_size(sizeof(*rq->wqe.frags),
(wq_sz << rq->wqe.info.log_num_frags)),
@@ -522,6 +526,8 @@ static int mlx5e_alloc_rq(struct mlx5e_channel *c,
}
if (xsk) {
+ rq->buff.first_frame_sz = xsk_umem_xdp_frame_sz(umem);
+
err = mlx5e_xsk_resize_reuseq(umem, num_xsk_frames);
if (unlikely(err)) {
mlx5_core_err(mdev, "Unable to allocate the Reuse Ring for %u frames\n",
The mlx5 driver have multiple memory models, which are also changed according to whether a XDP bpf_prog is attached. The 'rx_striding_rq' setting is adjusted via ethtool priv-flags e.g.: # ethtool --set-priv-flags mlx5p2 rx_striding_rq off On the general case with 4K page_size and regular MTU packet, then the frame_sz is 2048 and 4096 when XDP is enabled, in both modes. The info on the given frame size is stored differently depending on the RQ-mode and encoded in a union in struct mlx5e_rq union wqe/mpwqe. In rx striding mode rq->mpwqe.log_stride_sz is either 11 or 12, which corresponds to 2048 or 4096 (MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ). In non-striding mode (MLX5_WQ_TYPE_CYCLIC) the frag_stride is stored in rq->wqe.info.arr[0].frag_stride, for the first fragment, which is what the XDP case cares about. To reduce effect on fast-path, this patch determine the frame_sz at setup time, to avoid determining the memory model runtime. Variable is named first_frame_sz to make it clear that this is only the frame size of the first fragment. This mlx5 driver does a DMA-sync on XDP_TX action, but grow is safe as it have done a DMA-map on the entire PAGE_SIZE. The driver also already does a XDP length check against sq->hw_mtu on the possible XDP xmit paths mlx5e_xmit_xdp_frame() + mlx5e_xmit_xdp_frame_mpwqe(). Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> --- drivers/net/ethernet/mellanox/mlx5/core/en.h | 1 + drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c | 1 + drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 6 ++++++ 3 files changed, 8 insertions(+)