@@ -418,6 +418,40 @@ qca8k_mib_init(struct qca8k_priv *priv)
mutex_unlock(&priv->reg_mutex);
}
+static int
+qca8k_setup_sgmii(struct qca8k_priv *priv)
+{
+ const char *mode;
+ u32 val;
+
+ val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL);
+
+ val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
+ QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD;
+
+ if (of_property_read_bool(priv->dev->of_node, "sgmii-delay"))
+ val |= QCA8K_SGMII_CLK125M_DELAY;
+
+ if (of_property_read_string(priv->dev->of_node, "sgmii-mode", &mode)) {
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+
+ if (!strcasecmp(mode, "basex")) {
+ val |= QCA8K_SGMII_MODE_CTRL_BASEX;
+ } else if (!strcasecmp(mode, "mac")) {
+ val |= QCA8K_SGMII_MODE_CTRL_MAC;
+ } else if (!strcasecmp(mode, "phy")) {
+ val |= QCA8K_SGMII_MODE_CTRL_PHY;
+ } else {
+ pr_err("Unrecognised SGMII mode %s\n", mode);
+ return -EINVAL;
+ }
+ }
+
+ qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
+
+ return 0;
+}
+
static int
qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
{
@@ -458,7 +492,8 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
break;
case PHY_INTERFACE_MODE_SGMII:
qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
- break;
+
+ return qca8k_setup_sgmii(priv);
default:
pr_err("xMII mode %d not supported\n", mode);
return -EINVAL;
@@ -661,6 +696,13 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;
+ if (of_property_read_bool(priv->dev->of_node,
+ "disable-serdes-autoneg")) {
+ mask = qca8k_read(priv, QCA8K_REG_PWS) |
+ QCA8K_PWS_SERDES_AEN_DIS;
+ qca8k_write(priv, QCA8K_REG_PWS, mask);
+ }
+
/* Initialize CPU port pad mode (xMII type, delays...) */
ret = of_get_phy_mode(dsa_to_port(ds, QCA8K_CPU_PORT)->dn, &phy_mode);
if (ret) {
@@ -36,6 +36,8 @@
#define QCA8K_MAX_DELAY 3
#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
+#define QCA8K_REG_PWS 0x010
+#define QCA8K_PWS_SERDES_AEN_DIS BIT(7)
#define QCA8K_REG_MODULE_EN 0x030
#define QCA8K_MODULE_EN_MIB BIT(0)
#define QCA8K_REG_MIB 0x034
@@ -77,6 +79,16 @@
#define QCA8K_PORT_HDR_CTRL_ALL 2
#define QCA8K_PORT_HDR_CTRL_MGMT 1
#define QCA8K_PORT_HDR_CTRL_NONE 0
+#define QCA8K_REG_SGMII_CTRL 0x0e0
+#define QCA8K_SGMII_EN_PLL BIT(1)
+#define QCA8K_SGMII_EN_RX BIT(2)
+#define QCA8K_SGMII_EN_TX BIT(3)
+#define QCA8K_SGMII_EN_SD BIT(4)
+#define QCA8K_SGMII_CLK125M_DELAY BIT(7)
+#define QCA8K_SGMII_MODE_CTRL_MASK (BIT(22) | BIT(23))
+#define QCA8K_SGMII_MODE_CTRL_BASEX 0
+#define QCA8K_SGMII_MODE_CTRL_PHY BIT(22)
+#define QCA8K_SGMII_MODE_CTRL_MAC BIT(23)
/* EEE control registers */
#define QCA8K_REG_EEE_CTRL 0x100
The QCA8337(N) has an SGMII port which can operate in MAC, PHY or BASE-X mode depending on what it's connected to (e.g. CPU vs external PHY or SFP). At present the driver does no configuration of this port even if it is selected. Add support for making sure the SGMII is enabled if it's in use, and device tree support for configuring the connection details. Signed-off-by: Jonathan McDowell <noodles@earth.li> --- drivers/net/dsa/qca8k.c | 44 ++++++++++++++++++++++++++++++++++++++++- drivers/net/dsa/qca8k.h | 12 +++++++++++ 2 files changed, 55 insertions(+), 1 deletion(-)