@@ -25,11 +25,121 @@
#include "st_spi_fsm.h"
+static inline uint32_t stfsm_fifo_available(struct stfsm *fsm)
+{
+ return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f;
+}
+
+static void stfsm_clear_fifo(struct stfsm *fsm)
+{
+ uint32_t avail;
+
+ for (;;) {
+ avail = stfsm_fifo_available(fsm);
+ if (!avail)
+ break;
+
+ while (avail) {
+ readl(fsm->base + SPI_FAST_SEQ_DATA_REG);
+ avail--;
+ }
+ }
+}
+
+static int stfsm_set_mode(struct stfsm *fsm, uint32_t mode)
+{
+ int ret, timeout = 10;
+
+ /* Wait for controller to accept mode change */
+ while(--timeout) {
+ ret = readl(fsm->base + SPI_STA_MODE_CHANGE);
+ if (ret & 0x1)
+ break;
+ udelay(1);
+ }
+
+ if (!timeout)
+ return -EBUSY;
+
+ writel(mode, fsm->base + SPI_MODESELECT);
+
+ return 0;
+}
+
+static void stfsm_set_freq(struct stfsm *fsm, uint32_t spi_freq)
+{
+ uint32_t emi_freq;
+ uint32_t clk_div;
+
+ /* TODO: Make this dynamic */
+ emi_freq = STFSM_DEFAULT_EMI_FREQ;
+
+ /*
+ * Calculate clk_div - values between 2 and 128
+ * Multiple of 2, rounded up
+ */
+ clk_div = 2*((emi_freq + (2*spi_freq - 1))/(2*spi_freq));
+ if (clk_div < 2)
+ clk_div = 2;
+ else if (clk_div > 128)
+ clk_div = 128;
+
+ /*
+ * Determine a suitable delay for the IP to complete a change of
+ * direction of the FIFO. The required delay is related to the clock
+ * divider used. The following heuristics are based on empirical tests,
+ * using a 100MHz EMI clock.
+ */
+ if (clk_div <= 4)
+ fsm->fifo_dir_delay = 0;
+ else if (clk_div <= 10)
+ fsm->fifo_dir_delay = 1;
+ else
+ fsm->fifo_dir_delay = (clk_div + 9) / 10;
+
+ dev_dbg(fsm->dev, "emi_clk = %uHZ, spi_freq = %uHZ, clk_div = %u\n",
+ emi_freq, spi_freq, clk_div);
+
+ writel(clk_div, fsm->base + SPI_CLOCKDIV);
+}
+
+static int stfsm_init(struct stfsm *fsm)
+{
+ int ret;
+
+ /* Perform a soft reset of the FSM controller */
+ writel(SEQ_CFG_SWRESET, fsm->base + SPI_FAST_SEQ_CFG);
+ udelay(1);
+ writel(0, fsm->base + SPI_FAST_SEQ_CFG);
+
+ /* Set clock to 'safe' frequency initially */
+ stfsm_set_freq(fsm, STFSM_FLASH_SAFE_FREQ);
+
+ /* Switch to FSM */
+ ret = stfsm_set_mode(fsm, SPI_MODESELECT_FSM);
+ if (ret)
+ return ret;
+
+ /* Set timing parameters */
+ writel(SPI_CFG_DEVICE_ST |
+ SPI_CFG_DEFAULT_MIN_CS_HIGH |
+ SPI_CFG_DEFAULT_CS_SETUPHOLD |
+ SPI_CFG_DEFAULT_DATA_HOLD,
+ fsm->base + SPI_CONFIGDATA);
+ writel(STFSM_DEFAULT_WR_TIME, fsm->base + SPI_STATUS_WR_TIME_REG);
+
+ /* Clear FIFO, just in case */
+ stfsm_clear_fifo(fsm);
+
+ return 0;
+}
+
static int stfsm_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct resource *res;
struct stfsm *fsm;
+ int ret;
if (!np) {
dev_err(&pdev->dev, "No DT found\n");
@@ -66,6 +176,12 @@ static int stfsm_probe(struct platform_device *pdev)
mutex_init(&fsm->lock);
+ ret = stfsm_init(fsm);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to initialise FSM Controller\n");
+ return ret;
+ }
+
platform_set_drvdata(pdev, fsm);
fsm->mtd.dev.parent = &pdev->dev;
@@ -69,6 +69,10 @@
#define SPI_CFG_CS_SETUPHOLD(x) (((x) & 0xff) << 16)
#define SPI_CFG_DATA_HOLD(x) (((x) & 0xff) << 24)
+#define SPI_CFG_DEFAULT_MIN_CS_HIGH SPI_CFG_MIN_CS_HIGH(0x0AA)
+#define SPI_CFG_DEFAULT_CS_SETUPHOLD SPI_CFG_CS_SETUPHOLD(0xA0)
+#define SPI_CFG_DEFAULT_DATA_HOLD SPI_CFG_DATA_HOLD(0x00)
+
/*
* Register: SPI_FAST_SEQ_TRANSFER_SIZE
*/
@@ -180,12 +184,19 @@
#define STFSM_INST_WAIT STFSM_INSTR(STFSM_OPC_WAIT, 0)
#define STFSM_INST_STOP STFSM_INSTR(STFSM_OPC_STOP, 0)
+#define STFSM_DEFAULT_EMI_FREQ 100000000UL /* 100 MHz */
+#define STFSM_DEFAULT_WR_TIME STFSM_DEFAULT_EMI_FREQ * (15/1000) /* 15ms */
+
+#define STFSM_FLASH_SAFE_FREQ 10000000UL /* 10 MHz */
+
struct stfsm {
struct device *dev;
void __iomem *base;
struct resource *region;
struct mtd_info mtd;
struct mutex lock;
+
+ uint32_t fifo_dir_delay;
};
#endif /* ST_SPI_FSM_H */
This patch uses default values to initialise a connected flash chip. This includes; a device soft reset, setting of a safe working frequency, a switch into Fast Sequencing Mode, configuring of timing data and a purge of the FIFO. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- drivers/mtd/devices/st_spi_fsm.c | 116 +++++++++++++++++++++++++++++++++++++++ drivers/mtd/devices/st_spi_fsm.h | 11 ++++ 2 files changed, 127 insertions(+)