@@ -1,31 +1 @@
-* RS485 serial communications
-
-The RTS signal is capable of automatically controlling line direction for
-the built-in half-duplex mode.
-The properties described hereafter shall be given to a half-duplex capable
-UART node.
-
-Optional properties:
-- rs485-rts-delay: prop-encoded-array <a b> where:
- * a is the delay between rts signal and beginning of data sent in milliseconds.
- it corresponds to the delay before sending data.
- * b is the delay between end of data sent and rts signal in milliseconds
- it corresponds to the delay after sending data and actual release of the line.
- If this property is not specified, <0 0> is assumed.
-- rs485-rts-active-low: drive RTS low when sending (default is high).
-- linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485
- feature at boot time. It can be disabled later with proper ioctl.
-- rs485-rx-during-tx: empty property that enables the receiving of data even
- while sending data.
-
-RS485 example for Atmel USART:
- usart0: serial@fff8c000 {
- compatible = "atmel,at91sam9260-usart";
- reg = <0xfff8c000 0x4000>;
- interrupts = <7>;
- atmel,use-dma-rx;
- atmel,use-dma-tx;
- linux,rs485-enabled-at-boot-time;
- rs485-rts-delay = <0 200>; // in milliseconds
- };
-
+See rs485.yaml
new file mode 100644
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/rs485.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RS485 serial communications Bindings
+
+description: The RTS signal is capable of automatically controlling
+ line direction for the built-in half-duplex mode.
+ The properties described hereafter shall be given to a
+ half-duplex capable UART node.
+
+maintainers:
+ - Rob Herring <robh@kernel.org>
+
+properties:
+ rs485-rts-delay:
+ description: prop-encoded-array <a b>
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - items:
+ items:
+ - description:
+ Delay between rts signal and beginning of data sent in milliseconds.
+ It corresponds to the delay before sending data.
+ default: 0
+ maximum: 1000
+ - description:
+ Delay between end of data sent and rts signal in milliseconds.
+ It corresponds to the delay after sending data and actual release of the line.
+ default: 0
+ maximum: 1000
+
+ rs485-rts-active-low:
+ description: drive RTS low when sending (default is high).
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ linux,rs485-enabled-at-boot-time:
+ description: enables the rs485 feature at boot time. It can be disabled later with proper ioctl.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ rs485-rx-during-tx:
+ description: enables the receiving of data even while sending data.
+ $ref: /schemas/types.yaml#/definitions/flag
Convert rs485 binding to yaml style file. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- version 2: - remove types inside rs485-rts-delay property and add a maximum for delay values Documentation/devicetree/bindings/serial/rs485.txt | 32 +-------------- .../devicetree/bindings/serial/rs485.yaml | 45 ++++++++++++++++++++++ 2 files changed, 46 insertions(+), 31 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/rs485.yaml