diff mbox series

[v3,1/8] media: v4l2-subdv: Introduce [s|g]et_mbus_config pad ops

Message ID 20200514164540.507233-3-jacopo+renesas@jmondi.org
State New
Headers show
Series v4l2-subdev: Introduce [g|s]et_mbus_format pad op | expand

Commit Message

Jacopo Mondi May 14, 2020, 4:45 p.m. UTC
Introduce two new pad operations to allow retrieving and configuring the
media bus configuration on a subdevice pad.

The newly introduced operations aims to replace the s/g_mbus_config video
operations, which have been on their way to be deprecated since a long
time.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 include/media/v4l2-subdev.h | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
diff mbox series

Patch

diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index a4848de59852..8d5f4a255b87 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -670,6 +670,32 @@  struct v4l2_subdev_pad_config {
  *
  * @set_frame_desc: set the low level media bus frame parameters, @fd array
  *                  may be adjusted by the subdev driver to device capabilities.
+ *
+ * @get_mbus_config: get the current media bus configuration. This operation is
+ *		     intended to be used to synchronize the media bus
+ *		     configuration parameters between receivers and
+ *		     transmitters. The static bus configuration is usually
+ *		     received from the firmware interface, and updated
+ *		     dynamically using this operation to retrieve bus
+ *		     configuration parameters which could change at run-time.
+ *		     Callers should make sure they get the most up-to-date as
+ *		     possible configuration from the connected sub-device,
+ *		     likely calling this operation as close as possible to
+ *		     stream on time. The operation is allowed to fail if the
+ *		     pad index it has been called on is unsupported.
+ *
+ * @set_mbus_config: set the media bus configuration. This operations is
+ *		     intended to allow, in combination with the
+ *		     get_mbus_format operation, the negotiation of media bus
+ *		     configuration parameters between media subdevices.
+ *		     The initial media bus configuration is retrieved from
+ *		     the firmware interface and later updated through this
+ *		     operation if the sub-device allows changing it.
+ *		     The operation shall not fail if the requested configuration
+ *		     is not supported, but the driver shall update the received
+ *		     %config argument to reflect what has been actually applied
+ *		     to the hardware. The operation is allowed to fail if the
+ *		     pad index it has been called on is unsupported.
  */
 struct v4l2_subdev_pad_ops {
 	int (*init_cfg)(struct v4l2_subdev *sd,
@@ -710,6 +736,10 @@  struct v4l2_subdev_pad_ops {
 			      struct v4l2_mbus_frame_desc *fd);
 	int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad,
 			      struct v4l2_mbus_frame_desc *fd);
+	int (*get_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+			       struct v4l2_mbus_config *config);
+	int (*set_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+			       struct v4l2_mbus_config *config);
 };
 
 /**