deleted file mode 100644
@@ -1,28 +0,0 @@
-STMicroelectonics Multi-Function eXpander (STMFX) Core bindings
-
-ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
-communication with the main MCU. Its main features are GPIO expansion, main
-MCU IDD measurement (IDD is the amount of current that flows through VDD) and
-resistive touchscreen controller.
-
-Required properties:
-- compatible: should be "st,stmfx-0300".
-- reg: I2C slave address of the device.
-- interrupts: interrupt specifier triggered by MFX_IRQ_OUT signal.
- Please refer to ../interrupt-controller/interrupt.txt
-
-Optional properties:
-- drive-open-drain: configure MFX_IRQ_OUT as open drain.
-- vdd-supply: phandle of the regulator supplying STMFX.
-
-Example:
-
- stmfx: stmfx@42 {
- compatible = "st,stmfx-0300";
- reg = <0x42>;
- interrupts = <8 IRQ_TYPE_EDGE_RISING>;
- interrupt-parent = <&gpioi>;
- vdd-supply = <&v3v3>;
- };
-
-Please refer to ../pinctrl/pinctrl-stmfx.txt for STMFX GPIO expander function bindings.
new file mode 100644
@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/stmfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics Multi-Function eXpander (STMFX) bindings
+
+description: ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
+ communication with the main MCU. Its main features are GPIO expansion,
+ main MCU IDD measurement (IDD is the amount of current that flows
+ through VDD) and resistive touchscreen controller.
+
+maintainers:
+ - Amelie Delaunay <amelie.delaunay@st.com>
+
+allOf:
+ - $ref: ../pinctrl/pincfg-node.yaml
+
+properties:
+ compatible:
+ const: st,stmfx-0300
+
+ reg:
+ enum: [ 0x42, 0x43 ]
+
+ interrupts:
+ maxItems: 1
+
+ drive-open-drain: true
+
+ vdd-supply:
+ maxItems: 1
+
+ stmfx-pin-controller:
+ type: object
+
+ properties:
+ compatible:
+ const: st,stmfx-0300-pinctrl
+
+ "#gpio-cells":
+ const: 2
+
+ "#interrupt-cells":
+ const: 2
+
+ gpio-controller: true
+
+ interrupt-controller: true
+
+ gpio-ranges:
+ description: if all STMFX pins[24:0] are available (no other STMFX function in use),
+ you should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+ if agpio[3:0] are not available (STMFX Touchscreen function in use),
+ you should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
+ if agpio[7:4] are not available (STMFX IDD function in use),
+ you should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
+ maxItems: 1
+
+ required:
+ - compatible
+ - "#gpio-cells"
+ - "#interrupt-cells"
+ - gpio-controller
+ - interrupt-controller
+ - gpio-ranges
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ stmfx@42 {
+ compatible = "st,stmfx-0300";
+ reg = <0x42>;
+ interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+ interrupt-parent = <&gpioi>;
+ vdd-supply = <&v3v3>;
+
+ stmfx-pin-controller {
+ compatible = "st,stmfx-0300-pinctrl";
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+ };
+ };
+ };
+
+...
deleted file mode 100644
@@ -1,116 +0,0 @@
-STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander bindings
-
-ST Multi-Function eXpander (STMFX) offers up to 24 GPIOs expansion.
-Please refer to ../mfd/stmfx.txt for STMFX Core bindings.
-
-Required properties:
-- compatible: should be "st,stmfx-0300-pinctrl".
-- #gpio-cells: should be <2>, the first cell is the GPIO number and the second
- cell is the gpio flags in accordance with <dt-bindings/gpio/gpio.h>.
-- gpio-controller: marks the device as a GPIO controller.
-- #interrupt-cells: should be <2>, the first cell is the GPIO number and the
- second cell is the interrupt flags in accordance with
- <dt-bindings/interrupt-controller/irq.h>.
-- interrupt-controller: marks the device as an interrupt controller.
-- gpio-ranges: specifies the mapping between gpio controller and pin
- controller pins. Check "Concerning gpio-ranges property" below.
-Please refer to ../gpio/gpio.txt.
-
-Please refer to pinctrl-bindings.txt for pin configuration.
-
-Required properties for pin configuration sub-nodes:
-- pins: list of pins to which the configuration applies.
-
-Optional properties for pin configuration sub-nodes (pinconf-generic ones):
-- bias-disable: disable any bias on the pin.
-- bias-pull-up: the pin will be pulled up.
-- bias-pull-pin-default: use the pin-default pull state.
-- bias-pull-down: the pin will be pulled down.
-- drive-open-drain: the pin will be driven with open drain.
-- drive-push-pull: the pin will be driven actively high and low.
-- output-high: the pin will be configured as an output driving high level.
-- output-low: the pin will be configured as an output driving low level.
-
-Note that STMFX pins[15:0] are called "gpio[15:0]", and STMFX pins[23:16] are
-called "agpio[7:0]". Example, to refer to pin 18 of STMFX, use "agpio2".
-
-Concerning gpio-ranges property:
-- if all STMFX pins[24:0] are available (no other STMFX function in use), you
- should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
-- if agpio[3:0] are not available (STMFX Touchscreen function in use), you
- should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
-- if agpio[7:4] are not available (STMFX IDD function in use), you
- should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
-
-
-Example:
-
- stmfx: stmfx@42 {
- ...
-
- stmfx_pinctrl: stmfx-pin-controller {
- compatible = "st,stmfx-0300-pinctrl";
- #gpio-cells = <2>;
- #interrupt-cells = <2>;
- gpio-controller;
- interrupt-controller;
- gpio-ranges = <&stmfx_pinctrl 0 0 24>;
-
- joystick_pins: joystick {
- pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
- drive-push-pull;
- bias-pull-up;
- };
- };
- };
-
-Example of STMFX GPIO consumers:
-
- joystick {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-0 = <&joystick_pins>;
- pinctrl-names = "default";
- button-0 {
- label = "JoySel";
- linux,code = <KEY_ENTER>;
- interrupt-parent = <&stmfx_pinctrl>;
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
- };
- button-1 {
- label = "JoyDown";
- linux,code = <KEY_DOWN>;
- interrupt-parent = <&stmfx_pinctrl>;
- interrupts = <1 IRQ_TYPE_EDGE_RISING>;
- };
- button-2 {
- label = "JoyLeft";
- linux,code = <KEY_LEFT>;
- interrupt-parent = <&stmfx_pinctrl>;
- interrupts = <2 IRQ_TYPE_EDGE_RISING>;
- };
- button-3 {
- label = "JoyRight";
- linux,code = <KEY_RIGHT>;
- interrupt-parent = <&stmfx_pinctrl>;
- interrupts = <3 IRQ_TYPE_EDGE_RISING>;
- };
- button-4 {
- label = "JoyUp";
- linux,code = <KEY_UP>;
- interrupt-parent = <&stmfx_pinctrl>;
- interrupts = <4 IRQ_TYPE_EDGE_RISING>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- orange {
- gpios = <&stmfx_pinctrl 17 1>;
- };
-
- blue {
- gpios = <&stmfx_pinctrl 19 1>;
- };
- }
Convert stmfx bindings to json-schema Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- Documentation/devicetree/bindings/mfd/stmfx.txt | 28 ----- Documentation/devicetree/bindings/mfd/stmfx.yaml | 100 ++++++++++++++++++ .../devicetree/bindings/pinctrl/pinctrl-stmfx.txt | 116 --------------------- 3 files changed, 100 insertions(+), 144 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mfd/stmfx.txt create mode 100644 Documentation/devicetree/bindings/mfd/stmfx.yaml delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt