@@ -195,6 +195,8 @@ struct imx_port {
unsigned int have_rtscts:1;
unsigned int have_rtsgpio:1;
unsigned int dte_mode:1;
+ unsigned int inverted_tx:1;
+ unsigned int inverted_rx:1;
struct clk *clk_ipg;
struct clk *clk_per;
const struct imx_uart_data *devdata;
@@ -1335,7 +1337,7 @@ static int imx_uart_startup(struct uart_port *port)
int retval, i;
unsigned long flags;
int dma_is_inited = 0;
- u32 ucr1, ucr2, ucr4;
+ u32 ucr1, ucr2, ucr3, ucr4;
retval = clk_prepare_enable(sport->clk_per);
if (retval)
@@ -1387,11 +1389,29 @@ static int imx_uart_startup(struct uart_port *port)
imx_uart_writel(sport, ucr1, UCR1);
- ucr4 = imx_uart_readl(sport, UCR4) & ~UCR4_OREN;
+ ucr4 = imx_uart_readl(sport, UCR4) & ~(UCR4_OREN | UCR4_INVR);
if (!sport->dma_is_enabled)
ucr4 |= UCR4_OREN;
+ if (sport->inverted_rx)
+ ucr4 |= UCR4_INVR;
imx_uart_writel(sport, ucr4, UCR4);
+ ucr3 = imx_uart_readl(sport, UCR3) & ~UCR3_INVT;
+ /*
+ * configure tx polarity before enabling tx
+ */
+ if (sport->inverted_tx)
+ ucr3 |= UCR3_INVT;
+
+ if (!imx_uart_is_imx1(sport)) {
+ ucr3 |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
+
+ if (sport->dte_mode)
+ /* disable broken interrupts */
+ ucr3 &= ~(UCR3_RI | UCR3_DCD);
+ }
+ imx_uart_writel(sport, ucr3, UCR3);
+
ucr2 = imx_uart_readl(sport, UCR2) & ~UCR2_ATEN;
ucr2 |= (UCR2_RXEN | UCR2_TXEN);
if (!sport->have_rtscts)
@@ -1404,20 +1424,6 @@ static int imx_uart_startup(struct uart_port *port)
ucr2 &= ~UCR2_RTSEN;
imx_uart_writel(sport, ucr2, UCR2);
- if (!imx_uart_is_imx1(sport)) {
- u32 ucr3;
-
- ucr3 = imx_uart_readl(sport, UCR3);
-
- ucr3 |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
-
- if (sport->dte_mode)
- /* disable broken interrupts */
- ucr3 &= ~(UCR3_RI | UCR3_DCD);
-
- imx_uart_writel(sport, ucr3, UCR3);
- }
-
/*
* Enable modem status interrupts
*/
@@ -2184,6 +2190,12 @@ static int imx_uart_probe_dt(struct imx_port *sport,
if (of_get_property(np, "rts-gpios", NULL))
sport->have_rtsgpio = 1;
+ if (of_get_property(np, "fsl,inverted-tx", NULL))
+ sport->inverted_tx = 1;
+
+ if (of_get_property(np, "fsl,inverted-rx", NULL))
+ sport->inverted_rx = 1;
+
return 0;
}
#else
The peripheral has support for inverting its input and/or output signals. This is useful if the hardware flips polarity of the peripheral's signal, such as swapped +/- pins on an RS-422 transceiver, or an inverting level shifter. Add support for these control registers via the device tree binding. As part of this change, make the writes of the various registers more uniform by moving the UCR3 block up near the other registers' blocks, since the INVT bit must be set before enabling the peripheral. Signed-off-by: George Hilliard <ghilliard@kopismobile.com> --- v1..v2: Remove confidentiality spam v2..v3: Set *and* clear register, and do it before TX enable v3..v4: Clean up bit manipulation; move UCR3 block so it's written once drivers/tty/serial/imx.c | 44 +++++++++++++++++++++++++--------------- 1 file changed, 28 insertions(+), 16 deletions(-)