@@ -523,11 +523,10 @@ pcie: pcie@1e140000 {
0x01000000 0 0x00000000 0x1e160000 0 0x00010000 /* io space */
>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0xF0000 0 0 1>;
- interrupt-map = <0x10000 0 0 1 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>,
- <0x20000 0 0 1 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>,
- <0x30000 0 0 1 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH
+ GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH
+ GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -97,6 +97,7 @@
* @pcie_rst: pointer to port reset control
* @gpio_rst: gpio reset
* @slot: port slot
+ * @irq: GIC irq
* @enabled: indicates if port is enabled
*/
struct mt7621_pcie_port {
@@ -107,6 +108,7 @@ struct mt7621_pcie_port {
struct reset_control *pcie_rst;
struct gpio_desc *gpio_rst;
u32 slot;
+ int irq;
bool enabled;
};
@@ -120,6 +122,7 @@ struct mt7621_pcie_port {
* @dev: Pointer to PCIe device
* @io_map_base: virtual memory base address for io
* @ports: pointer to PCIe port information
+ * @irq_map: irq mapping info according pcie link status
* @resets_inverted: depends on chip revision
* reset lines are inverted.
*/
@@ -135,6 +138,7 @@ struct mt7621_pcie {
} offset;
unsigned long io_map_base;
struct list_head ports;
+ int irq_map[PCIE_P2P_MAX];
bool resets_inverted;
};
@@ -279,6 +283,16 @@ static void setup_cm_memory_region(struct mt7621_pcie *pcie)
}
}
+static int mt7621_map_irq(const struct pci_dev *pdev, u8 slot, u8 pin)
+{
+ struct mt7621_pcie *pcie = pdev->bus->sysdata;
+ struct device *dev = pcie->dev;
+ int irq = pcie->irq_map[slot];
+
+ dev_info(dev, "bus=%d slot=%d irq=%d\n", pdev->bus->number, slot, irq);
+ return irq;
+}
+
static int mt7621_pci_parse_request_of_pci_ranges(struct mt7621_pcie *pcie)
{
struct device *dev = pcie->dev;
@@ -330,6 +344,7 @@ static int mt7621_pcie_parse_port(struct mt7621_pcie *pcie,
{
struct mt7621_pcie_port *port;
struct device *dev = pcie->dev;
+ struct platform_device *pdev = to_platform_device(dev);
struct device_node *pnode = dev->of_node;
struct resource regs;
char name[10];
@@ -371,6 +386,12 @@ static int mt7621_pcie_parse_port(struct mt7621_pcie *pcie,
port->slot = slot;
port->pcie = pcie;
+ port->irq = platform_get_irq(pdev, slot);
+ if (port->irq < 0) {
+ dev_err(dev, "Failed to get IRQ for PCIe%d\n", slot);
+ return -ENXIO;
+ }
+
INIT_LIST_HEAD(&port->list);
list_add_tail(&port->list, &pcie->ports);
@@ -585,13 +606,15 @@ static int mt7621_pcie_init_virtual_bridges(struct mt7621_pcie *pcie)
{
u32 pcie_link_status = 0;
u32 n;
- int i;
+ int i = 0;
u32 p2p_br_devnum[PCIE_P2P_MAX];
+ int irqs[PCIE_P2P_MAX];
struct mt7621_pcie_port *port;
list_for_each_entry(port, &pcie->ports, list) {
u32 slot = port->slot;
+ irqs[i++] = port->irq;
if (port->enabled)
pcie_link_status |= BIT(slot);
}
@@ -614,6 +637,15 @@ static int mt7621_pcie_init_virtual_bridges(struct mt7621_pcie *pcie)
(p2p_br_devnum[1] << PCIE_P2P_BR_DEVNUM1_SHIFT) |
(p2p_br_devnum[2] << PCIE_P2P_BR_DEVNUM2_SHIFT));
+ /* Assign IRQs */
+ n = 0;
+ for (i = 0; i < PCIE_P2P_MAX; i++)
+ if (pcie_link_status & BIT(i))
+ pcie->irq_map[n++] = irqs[i];
+
+ for (i = n; i < PCIE_P2P_MAX; i++)
+ pcie->irq_map[i] = -1;
+
return 0;
}
@@ -638,7 +670,7 @@ static int mt7621_pcie_register_host(struct pci_host_bridge *host,
host->busnr = pcie->busn.start;
host->dev.parent = pcie->dev;
host->ops = &mt7621_pci_ops;
- host->map_irq = of_irq_parse_and_map_pci;
+ host->map_irq = mt7621_map_irq;
host->swizzle_irq = pci_common_swizzle;
host->sysdata = pcie;
MT7621 has three assigned interrupts for the pcie. This interrupts should properly being mapped taking into account which devices are finally connected in which bus according to link status. So the irq mappings should be as follows according to link status (three bits indicating which devices are link up): * For PCIe Bus 1 slot 0: - status = 0x2 || status = 0x6 => IRQ = pcie1_irq (24). - status = 0x4 => IRQ = pcie2_irq (25). - default => IRQ = pcie0_irq (23). * For PCIe Bus 2 slot 0: - status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25). - default => IRQ = pcie1_irq (24). * For PCIe Bus 2 slot 1: - status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25). - default => IRQ = pcie1_irq (24). * For PCIe Bus 3 any slot: - default => IRQ = pcie2_irq (25). Because of this, the function 'of_irq_parse_and_map_pci' cannot be used and we need to change device tree information from using the 'interrupt-map' and 'interrupt-map-mask' properties into an 'interrupts' property to be able to get irq information from the ports using the 'platform_get_irq' and storing an 'irq-map' into the pcie driver data node to properly map correct irq using a new 'mt7621_map_irq' function where this map will be read and the correct irq returned. Fixes: 46d093124df4 ("staging: mt7621-pci: improve interrupt mapping") Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> --- Tested in gnubee pc1 (which uses all the buses and also worked without changes) and tested also in ZyXEL LTE3301-PLUS which has PCIe and a mt7615e connected to second bus on the first phy where the current mapping was failing and this changes seems to fix the mapping problems. On gnubee we get: # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 ... 23: 0 0 0 0 MIPS GIC 11 ahci[0000:01:00.0] 24: 0 0 0 0 MIPS GIC 31 ahci[0000:02:00.0] 25: 279 0 0 0 MIPS GIC 32 ahci[0000:03:00.0] On the ZyXEL LTE3301-PLUS before this changes (wrongly '23' (pcie0 one) is assigned): root@OpenWrt:/# cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 ... 23: 0 0 0 0 MIPS GIC 11 mt7615e After this changes: root@OpenWrt:/# cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 ... 24: 85 0 0 0 MIPS GIC 31 mt7615e Thanks! drivers/staging/mt7621-dts/mt7621.dtsi | 9 +++---- drivers/staging/mt7621-pci/pci-mt7621.c | 36 +++++++++++++++++++++++-- 2 files changed, 38 insertions(+), 7 deletions(-)