@@ -91,6 +91,8 @@
#define REG_MMU1_INVLD_PA 0x148
#define REG_MMU0_INT_ID 0x150
#define REG_MMU1_INT_ID 0x154
+#define F_MMU_INT_ID_COMM_ID(a) (((a) >> 9) & 0x7)
+#define F_MMU_INT_ID_SUB_COMM_ID(a) (((a) >> 7) & 0x3)
#define F_MMU_INT_ID_LARB_ID(a) (((a) >> 7) & 0x7)
#define F_MMU_INT_ID_PORT_ID(a) (((a) >> 2) & 0x1f)
@@ -229,7 +231,7 @@ static irqreturn_t mtk_iommu_isr(int irq, void *dev_id)
struct mtk_iommu_data *data = dev_id;
struct mtk_iommu_domain *dom = data->m4u_dom;
u32 int_state, regval, fault_iova, fault_pa;
- unsigned int fault_larb, fault_port;
+ unsigned int fault_larb, fault_port, sub_comm = 0;
bool layer, write;
/* Read error info from registers */
@@ -245,10 +247,14 @@ static irqreturn_t mtk_iommu_isr(int irq, void *dev_id)
}
layer = fault_iova & F_MMU_FAULT_VA_LAYER_BIT;
write = fault_iova & F_MMU_FAULT_VA_WRITE_BIT;
- fault_larb = F_MMU_INT_ID_LARB_ID(regval);
fault_port = F_MMU_INT_ID_PORT_ID(regval);
-
- fault_larb = data->plat_data->larbid_remap[fault_larb];
+ if (data->plat_data->has_sub_comm) {
+ fault_larb = F_MMU_INT_ID_COMM_ID(regval);
+ sub_comm = F_MMU_INT_ID_SUB_COMM_ID(regval);
+ } else {
+ fault_larb = F_MMU_INT_ID_LARB_ID(regval);
+ }
+ fault_larb = data->plat_data->larbid_remap[fault_larb][sub_comm];
if (report_iommu_fault(&dom->domain, data->dev, fault_iova,
write ? IOMMU_FAULT_WRITE : IOMMU_FAULT_READ)) {
@@ -778,7 +784,7 @@ static const struct mtk_iommu_plat_data mt2712_data = {
.has_bclk = true,
.has_vld_pa_rng = true,
.inv_sel_reg = REG_MMU_INV_SEL_GEN1,
- .larbid_remap = {0, 1, 2, 3, 4, 5, 6, 7, 8, 9},
+ .larbid_remap = {{0}, {1}, {2}, {3}, {4}, {5}, {6}, {7}},
};
static const struct mtk_iommu_plat_data mt8173_data = {
@@ -787,14 +793,14 @@ static const struct mtk_iommu_plat_data mt8173_data = {
.has_bclk = true,
.reset_axi = true,
.inv_sel_reg = REG_MMU_INV_SEL_GEN1,
- .larbid_remap = {0, 1, 2, 3, 4, 5}, /* Linear mapping. */
+ .larbid_remap = {{0}, {1}, {2}, {3}, {4}, {5}}, /* Linear mapping. */
};
static const struct mtk_iommu_plat_data mt8183_data = {
.m4u_plat = M4U_MT8183,
.reset_axi = true,
.inv_sel_reg = REG_MMU_INV_SEL_GEN1,
- .larbid_remap = {0, 4, 5, 6, 7, 2, 3, 1},
+ .larbid_remap = {{0}, {4}, {5}, {6}, {7}, {2}, {3}, {1}},
};
static const struct of_device_id mtk_iommu_of_ids[] = {
@@ -41,10 +41,11 @@ struct mtk_iommu_plat_data {
/* HW will use the EMI clock if there isn't the "bclk". */
bool has_bclk;
bool has_misc_ctrl;
+ bool has_sub_comm;
bool has_vld_pa_rng;
bool reset_axi;
u32 inv_sel_reg;
- unsigned char larbid_remap[MTK_LARB_NR_MAX];
+ unsigned char larbid_remap[8][4];
};
struct mtk_iommu_domain;
The max larb number that a iommu HW support is 8(larb0~larb7 in the below diagram). If the larb's number is over 8, we use a sub_common for merging several larbs into one larb. At this case, we will extend larb_id: bit[11:9] means common-id; bit[8:7] means subcommon-id; From these two variable, we could get the real larb number when translation fault happen. The diagram is as below: EMI | IOMMU | ----------------- | | common1 common0 | | ----------------- | smi common | ------------------------------------ | | | | | | 3'd0 3'd1 3'd2 3'd3 ... 3'd7 <-common_id(max is 8) | | | | | | Larb0 Larb1 | Larb3 ... Larb7 | smi sub common | -------------------------- | | | | 2'd0 2'd1 2'd2 2'd3 <-sub_common_id(max is 4) | | | | Larb8 Larb9 Larb10 Larb11 In this patch we extern larb_remap[] to larb_remap[8][4] for this. larb_remap[x][y]: x mean common-id above, y means subcommon_id above. We can also distinguish if the M4U HW has sub_common by has_sub_comm property. Signed-off-by: Chao Hao <chao.hao@mediatek.com> Reviewed-by: Yong Wu <yong.wu@mediatek.com> --- drivers/iommu/mtk_iommu.c | 20 +++++++++++++------- drivers/iommu/mtk_iommu.h | 3 ++- 2 files changed, 15 insertions(+), 8 deletions(-) -- 2.18.0