diff mbox series

[2/2] arm64: dts: ti: j721e-common-proc-board: Analog audio support

Message ID 20200702131424.21241-3-peter.ujfalusi@ti.com
State Superseded
Headers show
Series arm64: dts: ti: k3-j721e-common-proc-board: Enable audio support | expand

Commit Message

Peter Ujfalusi July 2, 2020, 1:14 p.m. UTC 
The codec is wired in multi DIN/DOUT setup (DIN1/2/3/4/DOUT1/2/3 is
connected to McASP serializer).

To support wide range of audio features a generic sound card can not be
used since we need to use different reference clock source for 44.1 and
48 KHz family of sampling rates.
Depending on the sample size we also need to use different slot width to
be able to support 16 and 24 bits.

There are couple of notable difference compared to DIN1/DOUT1 mode:
the channel mapping is 'random' for first look compared to the single
serializer setup:
        _      _      _
       |o|c1  |o|p1  |o|p3
 _     | |    | |    | |
|o|c3  |o|c2  |o|p4  |o|p2
------------------------

c1/2/3 - capture jacks (3rd is line)
p1/2/3/4 - playback jacks (4th is line)

2 channel audio (stereo):
0 (left):  p1/c1 left
1 (right): p1/c1 right

4 channel audio:
0: p1/c1 left
1: p2/c2 left
2: p1/c1 right
3: p2/c2 right

6 channel audio
0: p1/c1 left
1: p2/c2 left
2: p3/c3 left
3: p1/c1 right
4: p2/c2 right
5: p3/c3 right

8 channel audio
0: p1/c1 left
1: p2/c2 left
2: p3/c3 left
3: p4 left
4: p1/c1 right
5: p2/c2 right
6: p3/c3 right
7: p4 right

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

---
 .../dts/ti/k3-j721e-common-proc-board.dts     | 137 ++++++++++++++++++
 1 file changed, 137 insertions(+)

-- 
Peter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

Comments

Peter Ujfalusi July 3, 2020, 6:09 a.m. UTC | #1 
On 02/07/2020 16.14, Peter Ujfalusi wrote:
> The codec is wired in multi DIN/DOUT setup (DIN1/2/3/4/DOUT1/2/3 is

> connected to McASP serializer).

> 

> To support wide range of audio features a generic sound card can not be

> used since we need to use different reference clock source for 44.1 and

> 48 KHz family of sampling rates.

> Depending on the sample size we also need to use different slot width to

> be able to support 16 and 24 bits.

> 

> There are couple of notable difference compared to DIN1/DOUT1 mode:

> the channel mapping is 'random' for first look compared to the single

> serializer setup:

>         _      _      _

>        |o|c1  |o|p1  |o|p3

>  _     | |    | |    | |

> |o|c3  |o|c2  |o|p4  |o|p2

> ------------------------

> 

> c1/2/3 - capture jacks (3rd is line)

> p1/2/3/4 - playback jacks (4th is line)

> 

> 2 channel audio (stereo):

> 0 (left):  p1/c1 left

> 1 (right): p1/c1 right

> 

> 4 channel audio:

> 0: p1/c1 left

> 1: p2/c2 left

> 2: p1/c1 right

> 3: p2/c2 right

> 

> 6 channel audio

> 0: p1/c1 left

> 1: p2/c2 left

> 2: p3/c3 left

> 3: p1/c1 right

> 4: p2/c2 right

> 5: p3/c3 right

> 

> 8 channel audio

> 0: p1/c1 left

> 1: p2/c2 left

> 2: p3/c3 left

> 3: p4 left

> 4: p1/c1 right

> 5: p2/c2 right

> 6: p3/c3 right

> 7: p4 right

> 

> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

> ---

>  .../dts/ti/k3-j721e-common-proc-board.dts     | 137 ++++++++++++++++++

>  1 file changed, 137 insertions(+)

> 

> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts

> index 1f1fee85acca..6c0f1ce6f4a6 100644

> --- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts

> +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts

> @@ -9,6 +9,7 @@

>  #include <dt-bindings/gpio/gpio.h>

>  #include <dt-bindings/input/input.h>

>  #include <dt-bindings/net/ti-dp83867.h>

> +#include <dt-bindings/sound/ti-mcasp.h>


This include is not needed, I'll send v2 shortly.

>  

>  / {

>  	chosen {

> @@ -34,6 +35,55 @@ sw11: sw11 {

>  			gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>;

>  		};

>  	};

> +

> +	evm_12v0: fixedregulator-evm12v0 {

> +		/* main supply */

> +		compatible = "regulator-fixed";

> +		regulator-name = "evm_12v0";

> +		regulator-min-microvolt = <12000000>;

> +		regulator-max-microvolt = <12000000>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	vsys_3v3: fixedregulator-vsys3v3 {

> +		/* Output of LMS140 */

> +		compatible = "regulator-fixed";

> +		regulator-name = "vsys_3v3";

> +		regulator-min-microvolt = <3300000>;

> +		regulator-max-microvolt = <3300000>;

> +		vin-supply = <&evm_12v0>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	vsys_5v0: fixedregulator-vsys5v0 {

> +		/* Output of LM5140 */

> +		compatible = "regulator-fixed";

> +		regulator-name = "vsys_5v0";

> +		regulator-min-microvolt = <5000000>;

> +		regulator-max-microvolt = <5000000>;

> +		vin-supply = <&evm_12v0>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	sound0: sound@0 {

> +		compatible = "ti,j721e-cpb-audio";

> +		model = "j721e-cpb";

> +

> +		ti,cpb-mcasp = <&mcasp10>;

> +		ti,cpb-codec = <&pcm3168a_1>;

> +

> +		clocks = <&k3_clks 184 1>,

> +			 <&k3_clks 184 2>, <&k3_clks 184 4>,

> +			 <&k3_clks 157 371>,

> +			 <&k3_clks 157 400>, <&k3_clks 157 401>;

> +		clock-names = "cpb-mcasp-auxclk",

> +			      "cpb-mcasp-auxclk-48000", "cpb-mcasp-auxclk-44100",

> +			      "cpb-codec-scki",

> +			      "cpb-codec-scki-48000", "cpb-codec-scki-44100";

> +	};

>  };

>  

>  &main_pmx0 {

> @@ -102,6 +152,26 @@ J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */

>  			J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */

>  		>;

>  	};

> +

> +	mcasp10_pins_default: mcasp10_pins_default {

> +		pinctrl-single,pins = <

> +			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */

> +			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */

> +			J721E_IOPAD(0x160, PIN_OUTPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */

> +			J721E_IOPAD(0x164, PIN_OUTPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */

> +			J721E_IOPAD(0x170, PIN_OUTPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */

> +			J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */

> +			J721E_IOPAD(0x198, PIN_INPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */

> +			J721E_IOPAD(0x19c, PIN_INPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */

> +			J721E_IOPAD(0x1a0, PIN_INPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */

> +		>;

> +	};

> +

> +	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {

> +		pinctrl-single,pins = <

> +			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */

> +		>;

> +	};

>  };

>  

>  &wkup_pmx0 {

> @@ -401,6 +471,22 @@ exp2: gpio@22 {

>  		reg = <0x22>;

>  		gpio-controller;

>  		#gpio-cells = <2>;

> +

> +		p09 {

> +			/* P11 - MCASP/TRACE_MUX_S0 */

> +			gpio-hog;

> +			gpios = <9 GPIO_ACTIVE_HIGH>;

> +			output-low;

> +			line-name = "MCASP/TRACE_MUX_S0";

> +		};

> +

> +		p10 {

> +			/* P12 - MCASP/TRACE_MUX_S1 */

> +			gpio-hog;

> +			gpios = <10 GPIO_ACTIVE_HIGH>;

> +			output-high;

> +			line-name = "MCASP/TRACE_MUX_S1";

> +		};

>  	};

>  };

>  

> @@ -423,6 +509,12 @@ exp4: gpio@20 {

>  	};

>  };

>  

> +&k3_clks {

> +	/* Confiure AUDIO_EXT_REFCLK2 pin as output */

> +	pinctrl-names = "default";

> +	pinctrl-0 = <&audi_ext_refclk2_pins_default>;

> +};

> +

>  &main_i2c3 {

>  	pinctrl-names = "default";

>  	pinctrl-0 = <&main_i2c3_pins_default>;

> @@ -434,6 +526,31 @@ exp3: gpio@20 {

>  		gpio-controller;

>  		#gpio-cells = <2>;

>  	};

> +

> +	pcm3168a_1: audio-codec@44 {

> +		compatible = "ti,pcm3168a";

> +		reg = <0x44>;

> +

> +		#sound-dai-cells = <1>;

> +

> +		reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;

> +

> +		/* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */

> +		clocks = <&k3_clks 157 371>;

> +		clock-names = "scki";

> +

> +		/* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */

> +		assigned-clocks = <&k3_clks 157 371>;

> +		assigned-clock-parents = <&k3_clks 157 400>;

> +		assigned-clock-rates = <24576000>; /* for 48KHz */

> +

> +		VDD1-supply = <&vsys_3v3>;

> +		VDD2-supply = <&vsys_3v3>;

> +		VCCAD1-supply = <&vsys_5v0>;

> +		VCCAD2-supply = <&vsys_5v0>;

> +		VCCDA1-supply = <&vsys_5v0>;

> +		VCCDA2-supply = <&vsys_5v0>;

> +	};

>  };

>  

>  &main_i2c6 {

> @@ -486,3 +603,23 @@ &dss {

>  				 <&k3_clks 152 11>,	/* PLL18_HSDIV0 */

>  				 <&k3_clks 152 18>;	/* PLL23_HSDIV0 */

>  };

> +

> +&mcasp10 {

> +	#sound-dai-cells = <0>;

> +

> +	pinctrl-names = "default";

> +	pinctrl-0 = <&mcasp10_pins_default>;

> +

> +	op-mode = <0>;          /* MCASP_IIS_MODE */

> +	tdm-slots = <2>;

> +	auxclk-fs-ratio = <256>;

> +

> +	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */

> +		1 1 1 1

> +		2 2 2 0

> +	>;

> +	tx-num-evt = <0>;

> +	rx-num-evt = <0>;

> +

> +	status = "okay";

> +};

> 


- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 1f1fee85acca..6c0f1ce6f4a6 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -9,6 +9,7 @@ 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/sound/ti-mcasp.h>
 
 / {
 	chosen {
@@ -34,6 +35,55 @@  sw11: sw11 {
 			gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LMS140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	sound0: sound@0 {
+		compatible = "ti,j721e-cpb-audio";
+		model = "j721e-cpb";
+
+		ti,cpb-mcasp = <&mcasp10>;
+		ti,cpb-codec = <&pcm3168a_1>;
+
+		clocks = <&k3_clks 184 1>,
+			 <&k3_clks 184 2>, <&k3_clks 184 4>,
+			 <&k3_clks 157 371>,
+			 <&k3_clks 157 400>, <&k3_clks 157 401>;
+		clock-names = "cpb-mcasp-auxclk",
+			      "cpb-mcasp-auxclk-48000", "cpb-mcasp-auxclk-44100",
+			      "cpb-codec-scki",
+			      "cpb-codec-scki-48000", "cpb-codec-scki-44100";
+	};
 };
 
 &main_pmx0 {
@@ -102,6 +152,26 @@  J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
 			J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
 		>;
 	};
+
+	mcasp10_pins_default: mcasp10_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
+			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
+			J721E_IOPAD(0x160, PIN_OUTPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */
+			J721E_IOPAD(0x164, PIN_OUTPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */
+			J721E_IOPAD(0x170, PIN_OUTPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */
+			J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */
+			J721E_IOPAD(0x198, PIN_INPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */
+			J721E_IOPAD(0x19c, PIN_INPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */
+			J721E_IOPAD(0x1a0, PIN_INPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */
+		>;
+	};
+
+	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -401,6 +471,22 @@  exp2: gpio@22 {
 		reg = <0x22>;
 		gpio-controller;
 		#gpio-cells = <2>;
+
+		p09 {
+			/* P11 - MCASP/TRACE_MUX_S0 */
+			gpio-hog;
+			gpios = <9 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "MCASP/TRACE_MUX_S0";
+		};
+
+		p10 {
+			/* P12 - MCASP/TRACE_MUX_S1 */
+			gpio-hog;
+			gpios = <10 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "MCASP/TRACE_MUX_S1";
+		};
 	};
 };
 
@@ -423,6 +509,12 @@  exp4: gpio@20 {
 	};
 };
 
+&k3_clks {
+	/* Confiure AUDIO_EXT_REFCLK2 pin as output */
+	pinctrl-names = "default";
+	pinctrl-0 = <&audi_ext_refclk2_pins_default>;
+};
+
 &main_i2c3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c3_pins_default>;
@@ -434,6 +526,31 @@  exp3: gpio@20 {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	pcm3168a_1: audio-codec@44 {
+		compatible = "ti,pcm3168a";
+		reg = <0x44>;
+
+		#sound-dai-cells = <1>;
+
+		reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;
+
+		/* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */
+		clocks = <&k3_clks 157 371>;
+		clock-names = "scki";
+
+		/* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */
+		assigned-clocks = <&k3_clks 157 371>;
+		assigned-clock-parents = <&k3_clks 157 400>;
+		assigned-clock-rates = <24576000>; /* for 48KHz */
+
+		VDD1-supply = <&vsys_3v3>;
+		VDD2-supply = <&vsys_3v3>;
+		VCCAD1-supply = <&vsys_5v0>;
+		VCCAD2-supply = <&vsys_5v0>;
+		VCCDA1-supply = <&vsys_5v0>;
+		VCCDA2-supply = <&vsys_5v0>;
+	};
 };
 
 &main_i2c6 {
@@ -486,3 +603,23 @@  &dss {
 				 <&k3_clks 152 11>,	/* PLL18_HSDIV0 */
 				 <&k3_clks 152 18>;	/* PLL23_HSDIV0 */
 };
+
+&mcasp10 {
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp10_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	auxclk-fs-ratio = <256>;
+
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+		1 1 1 1
+		2 2 2 0
+	>;
+	tx-num-evt = <0>;
+	rx-num-evt = <0>;
+
+	status = "okay";
+};