diff mbox series

[v1] arm64: dts: sc7180: add dsi controller and phy entries for idp dts

Message ID 1580218617-30293-1-git-send-email-harigovi@codeaurora.org
State New
Headers show
Series [v1] arm64: dts: sc7180: add dsi controller and phy entries for idp dts | expand

Commit Message

Harigovindan P Jan. 28, 2020, 1:36 p.m. UTC
Adding dsi controller and phy entries for idp dt.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/sc7180-idp.dts | 56 +++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

Comments

Matthias Kaehlcke Jan. 28, 2020, 7:53 p.m. UTC | #1
Hi,

On Tue, Jan 28, 2020 at 07:06:57PM +0530, Harigovindan P wrote:
> Adding dsi controller and phy entries for idp dt.
> 
> Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts | 56 +++++++++++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 388f50a..9f42367 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -7,6 +7,7 @@
>  
>  /dts-v1/;
>  
> +#include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>  #include "sc7180.dtsi"
>  #include "pm6150.dtsi"
> @@ -232,6 +233,50 @@
>  	};
>  };
>  
> +&dsi_controller {
> +	status = "okay";
> +
> +	vdda-supply = <&vreg_l3c_1p2>;
> +
> +	panel@0 {
> +		compatible = "visionox,rm69299-1080p-display";

This depends on the series "Add support for rm69299 Visionox panel
driver and add devicetree bindings for visionox panel"
(https://patchwork.kernel.org/cover/11320773/) which hasn't landed
IIUC. This should be mentioned after '---'.

> +		reg = <0>;
> +
> +		vdda-supply = <&vreg_l8c_1p8>;
> +		vdd3p3-supply = <&vreg_l18a_2p8>;
> +
> +		pinctrl-names = "default", "suspend";
> +		pinctrl-0 = <&disp_pins_default>;
> +		pinctrl-1 = <&disp_pins_default>;

Is there a point for listing a suspend configuration if it is the same
as the default?

> +		reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			port@0 {
> +				reg = <0>;
> +				panel0_in: endpoint {
> +					remote-endpoint = <&dsi0_out>;

The 'dsi0_out' node is added by 'arm64: dts: sc7180: add display dt nodes'
(https://patchwork.kernel.org/patch/11354253/), which has not landed. So
either you should list it as dependency below the commit message, or
(probably better) send the two patches in the same series.

> +				};
> +			};
> +		};
> +	};
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&panel0_in>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
> +};
> +
> +&dsi_phy {

Also this node does not exist yet, it also depends on the patch mentioned
above.

> +	status = "okay";
> +};
> +
>  &qspi {
>  	status = "okay";
>  	pinctrl-names = "default";
> @@ -289,6 +334,17 @@
>  
>  /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>  
> +&pm6150l_gpio {
> +	disp_pins_default: disp-pins-default{

nit: missing blank before curly brace

If there is no suspend configuration you can get rid of the 'default'
suffix.

Since this is only a single pin I would suggest to use a name that
describes the function of the pin or the name used in the schematic
instead of 'disp-pins'.

Thanks

Matthias
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 388f50a..9f42367 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -7,6 +7,7 @@ 
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sc7180.dtsi"
 #include "pm6150.dtsi"
@@ -232,6 +233,50 @@ 
 	};
 };
 
+&dsi_controller {
+	status = "okay";
+
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	panel@0 {
+		compatible = "visionox,rm69299-1080p-display";
+		reg = <0>;
+
+		vdda-supply = <&vreg_l8c_1p8>;
+		vdd3p3-supply = <&vreg_l18a_2p8>;
+
+		pinctrl-names = "default", "suspend";
+		pinctrl-0 = <&disp_pins_default>;
+		pinctrl-1 = <&disp_pins_default>;
+
+		reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel0_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel0_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&dsi_phy {
+	status = "okay";
+};
+
 &qspi {
 	status = "okay";
 	pinctrl-names = "default";
@@ -289,6 +334,17 @@ 
 
 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 
+&pm6150l_gpio {
+	disp_pins_default: disp-pins-default{
+		pins = "gpio3";
+		function = "func1";
+		qcom,drive-strength = <2>;
+		power-source = <0>;
+		bias-disable;
+		output-low;
+	};
+};
+
 &qspi_clk {
 	pinconf {
 		pins = "gpio63";