diff mbox series

[13/19] mmc: sdricoh_cs: Throttle polling rate for commands

Message ID 20200414161413.3036-14-ulf.hansson@linaro.org
State Superseded
Headers show
Series mmc: Improve host driver's support for R1B responses | expand

Commit Message

Ulf Hansson April 14, 2020, 4:14 p.m. UTC
Rather than to poll in a busy-loop, let's convert into using
readl_poll_timeout() and insert a small delay between each polling
attempts. In particular, this avoids hogging the CPU.

Additionally, to convert to readl_poll_timeout() we also need to switch
from using a specific number of polling attempts, into a specific timeout
in us instead. The previous 100000 attempts, is translated into a total
timeout of total 1s, as that seemed like reasonable value to pick.

Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

---
 drivers/mmc/host/sdricoh_cs.c | 32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

-- 
2.20.1
diff mbox series

Patch

diff --git a/drivers/mmc/host/sdricoh_cs.c b/drivers/mmc/host/sdricoh_cs.c
index 7e407fb6dab8..d7a191f14337 100644
--- a/drivers/mmc/host/sdricoh_cs.c
+++ b/drivers/mmc/host/sdricoh_cs.c
@@ -59,7 +59,7 @@  static unsigned int switchlocked;
 #define STATUS_BUSY              0x40000000
 
 /* timeouts */
-#define CMD_TIMEOUT       100000
+#define SDRICOH_CMD_TIMEOUT_US	1000000
 #define SDRICOH_DATA_TIMEOUT_US	1000000
 
 /* list of supported pcmcia devices */
@@ -157,8 +157,7 @@  static int sdricoh_query_status(struct sdricoh_host *host, unsigned int wanted)
 static int sdricoh_mmc_cmd(struct sdricoh_host *host, struct mmc_command *cmd)
 {
 	unsigned int status;
-	int result = 0;
-	unsigned int loop = 0;
+	int ret;
 	unsigned char opcode = cmd->opcode;
 
 	/* reset status reg? */
@@ -174,24 +173,23 @@  static int sdricoh_mmc_cmd(struct sdricoh_host *host, struct mmc_command *cmd)
 	/* fill parameters */
 	sdricoh_writel(host, R204_CMD_ARG, cmd->arg);
 	sdricoh_writel(host, R200_CMD, (0x10000 << 8) | opcode);
+
 	/* wait for command completion */
-	if (opcode) {
-		for (loop = 0; loop < CMD_TIMEOUT; loop++) {
-			status = sdricoh_readl(host, R21C_STATUS);
-			sdricoh_writel(host, R2E4_STATUS_RESP, status);
-			if (status  & STATUS_CMD_FINISHED)
-				break;
-		}
-		/* don't check for timeout in the loop it is not always
-		   reset correctly
-		*/
-		if (loop == CMD_TIMEOUT || status & STATUS_CMD_TIMEOUT)
-			result = -ETIMEDOUT;
+	if (!opcode)
+		return 0;
 
-	}
+	ret = readl_poll_timeout(host->iobase + R21C_STATUS, status,
+			sdricoh_status_ok(host, status, STATUS_CMD_FINISHED),
+			32, SDRICOH_CMD_TIMEOUT_US);
 
-	return result;
+	/*
+	 * Don't check for timeout status in the loop, as it's not always reset
+	 * correctly.
+	 */
+	if (ret || status & STATUS_CMD_TIMEOUT)
+		return -ETIMEDOUT;
 
+	return 0;
 }
 
 static int sdricoh_reset(struct sdricoh_host *host)