@@ -72,9 +72,11 @@
#define DP83867_STRAP_STS2_CLK_SKEW_NONE BIT(2)
/* PHY CTRL bits */
-#define DP83867_PHYCR_FIFO_DEPTH_SHIFT 14
+#define DP83867_PHYCR_TX_FIFO_DEPTH_SHIFT 14
+#define DP83867_PHYCR_RX_FIFO_DEPTH_SHIFT 12
#define DP83867_PHYCR_FIFO_DEPTH_MAX 0x03
-#define DP83867_PHYCR_FIFO_DEPTH_MASK GENMASK(15, 14)
+#define DP83867_PHYCR_TX_FIFO_DEPTH_MASK GENMASK(15, 14)
+#define DP83867_PHYCR_RX_FIFO_DEPTH_MASK GENMASK(13, 12)
#define DP83867_PHYCR_RESERVED_MASK BIT(11)
/* RGMIIDCTL bits */
@@ -103,7 +105,8 @@ enum {
struct dp83867_private {
u32 rx_id_delay;
u32 tx_id_delay;
- u32 fifo_depth;
+ u32 tx_fifo_depth;
+ u32 rx_fifo_depth;
int io_impedance;
int port_mirroring;
bool rxctrl_strap_quirk;
@@ -255,18 +258,32 @@ static int dp83867_of_init(struct phy_device *phydev)
dp83867->port_mirroring = DP83867_PORT_MIRROING_DIS;
ret = of_property_read_u32(of_node, "ti,fifo-depth",
- &dp83867->fifo_depth);
+ &dp83867->tx_fifo_depth);
if (ret) {
- phydev_err(phydev,
- "ti,fifo-depth property is required\n");
- return ret;
+ ret = of_property_read_u32(of_node, "tx-fifo-depth",
+ &dp83867->tx_fifo_depth);
+ if (ret)
+ dp83867->tx_fifo_depth =
+ DP83867_PHYCR_FIFO_DEPTH_4_B_NIB;
}
- if (dp83867->fifo_depth > DP83867_PHYCR_FIFO_DEPTH_MAX) {
- phydev_err(phydev,
- "ti,fifo-depth value %u out of range\n",
- dp83867->fifo_depth);
+
+ if (dp83867->tx_fifo_depth > DP83867_PHYCR_FIFO_DEPTH_MAX) {
+ phydev_err(phydev, "tx-fifo-depth value %u out of range\n",
+ dp83867->tx_fifo_depth);
return -EINVAL;
}
+
+ ret = of_property_read_u32(of_node, "rx-fifo-depth",
+ &dp83867->rx_fifo_depth);
+ if (ret)
+ dp83867->rx_fifo_depth = DP83867_PHYCR_FIFO_DEPTH_4_B_NIB;
+
+ if (dp83867->rx_fifo_depth > DP83867_PHYCR_FIFO_DEPTH_MAX) {
+ phydev_err(phydev, "rx-fifo-depth value %u out of range\n",
+ dp83867->rx_fifo_depth);
+ return -EINVAL;
+ }
+
return 0;
}
#else
@@ -305,12 +322,31 @@ static int dp83867_config_init(struct phy_device *phydev)
phy_clear_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4,
BIT(7));
+ if (phy_interface_is_rgmii(phydev) ||
+ phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+ val = phy_read(phydev, MII_DP83867_PHYCTRL);
+ if (val < 0)
+ return val;
+
+ val &= ~DP83867_PHYCR_TX_FIFO_DEPTH_MASK;
+ val |= (dp83867->tx_fifo_depth <<
+ DP83867_PHYCR_TX_FIFO_DEPTH_SHIFT);
+
+ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+ val &= ~DP83867_PHYCR_RX_FIFO_DEPTH_MASK;
+ val |= (dp83867->rx_fifo_depth <<
+ DP83867_PHYCR_RX_FIFO_DEPTH_SHIFT);
+ }
+
+ ret = phy_write(phydev, MII_DP83867_PHYCTRL, val);
+ if (ret)
+ return ret;
+ }
+
if (phy_interface_is_rgmii(phydev)) {
val = phy_read(phydev, MII_DP83867_PHYCTRL);
if (val < 0)
return val;
- val &= ~DP83867_PHYCR_FIFO_DEPTH_MASK;
- val |= (dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT);
/* The code below checks if "port mirroring" N/A MODE4 has been
* enabled during power on bootstrap.
This code changes the TI specific ti,fifo-depth to the common tx-fifo-depth property. The tx depth is applicable for both RGMII and SGMII modes of operation. rx-fifo-depth was added as well but this is only applicable for SGMII mode. So in summary if RGMII mode write tx fifo depth only if SGMII mode write both rx and tx fifo depths If the property is not populated in the device tree then set the value to the default values. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reported-by: Adrian Bunk <bunk@kernel.org> --- drivers/net/phy/dp83867.c | 62 +++++++++++++++++++++++++++++++-------- 1 file changed, 49 insertions(+), 13 deletions(-) -- 2.23.0