diff mbox series

[1/2] dt-bindings: net: dp83869: Add TI dp83869 phy

Message ID 20191105181826.25114-1-dmurphy@ti.com
State New
Headers show
Series [1/2] dt-bindings: net: dp83869: Add TI dp83869 phy | expand

Commit Message

Dan Murphy Nov. 5, 2019, 6:18 p.m. UTC
Add dt bindings for the TI dp83869 Gigabit ethernet phy
device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

CC: Rob Herring <robh+dt@kernel.org>
---
 .../devicetree/bindings/net/ti,dp83869.yaml   | 84 +++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/ti,dp83869.yaml

-- 
2.22.0.214.g8dca754b1e
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/ti,dp83869.yaml b/Documentation/devicetree/bindings/net/ti,dp83869.yaml
new file mode 100644
index 000000000000..6fe3e451da8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ti,dp83869.yaml
@@ -0,0 +1,84 @@ 
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI DP83869 ethernet PHY
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+
+maintainers:
+  - Dan Murphy <dmurphy@ti.com>
+
+description: |
+  The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver
+  with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and
+  1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and
+  100BASE-FX Fiber protocols.
+  This device interfaces to the MAC layer through Reduced GMII (RGMII) and
+  SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode,
+  the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX
+  conversions.  The DP83869HM can also support Bridge Conversion from RGMII to
+  SGMII and SGMII to RGMII.
+
+  Specifications about the charger can be found at:
+    http://www.ti.com/lit/ds/symlink/dp83869hm.pdf
+
+properties:
+  reg:
+    maxItems: 1
+
+  ti,min-output-impedance:
+    type: boolean
+    description: |
+       MAC Interface Impedance control to set the programmable output impedance
+       to a minimum value (35 ohms).
+
+  ti,max-output-impedance:
+    type: boolean
+    description: |
+       MAC Interface Impedance control to set the programmable output impedance
+       to a maximum value (70 ohms).
+
+  tx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+  rx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+  ti,clk-output-sel:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values.
+
+  ti,op-mode:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Operational mode for the PHY.  If this is not set then the operational
+       mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values
+
+required:
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/net/ti-dp83869.h>
+    mdio0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      ethphy0: ethernet-phy@0 {
+        reg = <0>;
+        tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+        ti,max-output-impedance = "true";
+        ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>;
+      };
+    };