| Message ID | 20190821184239.12364-2-vkoul@kernel.org |
|---|---|
| State | Accepted |
| Commit | e13c6d144fa0fd378c4062459736b4da28555414 |
| Headers | show |
| Series | [v4,1/8] arm64: dts: qcom: sm8150: Add base dts file | expand |
On Thu, Aug 22, 2019 at 12:14 AM Vinod Koul <vkoul@kernel.org> wrote: > > This add base DTS file with cpu, psci, firmware, clock node tlmm and > spmi and enables boot to console > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8150.dtsi | 308 +++++++++++++++++++++++++++ > 1 file changed, 308 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi > new file mode 100644 > index 000000000000..417b21d1897c > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi > @@ -0,0 +1,308 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. > + * Copyright (c) 2019, Linaro Limited > + */ > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/soc/qcom,rpmh-rsc.h> This include isn't strictly needed until patch 8, I believe. Sorry didn't catch this earlier. Other than that, for the series, Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> > +#include <dt-bindings/clock/qcom,rpmh.h> > + > +/ { > + interrupt-parent = <&intc>; > + > + #address-cells = <2>; > + #size-cells = <2>; > + > + chosen { }; > + > + clocks { > + xo_board: xo-board { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <38400000>; > + clock-output-names = "xo_board"; > + }; > + > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32764>; > + clock-output-names = "sleep_clk"; > + }; > + }; > + > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + L2_0: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + L3_0: l3-cache { > + compatible = "cache"; > + }; > + }; > + }; > + > + CPU1: cpu@100 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x100>; > + enable-method = "psci"; > + next-level-cache = <&L2_100>; > + L2_100: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + > + }; > + > + CPU2: cpu@200 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x200>; > + enable-method = "psci"; > + next-level-cache = <&L2_200>; > + L2_200: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU3: cpu@300 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x300>; > + enable-method = "psci"; > + next-level-cache = <&L2_300>; > + L2_300: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU4: cpu@400 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x400>; > + enable-method = "psci"; > + next-level-cache = <&L2_400>; > + L2_400: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU5: cpu@500 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x500>; > + enable-method = "psci"; > + next-level-cache = <&L2_500>; > + L2_500: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU6: cpu@600 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x600>; > + enable-method = "psci"; > + next-level-cache = <&L2_600>; > + L2_600: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU7: cpu@700 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x700>; > + enable-method = "psci"; > + next-level-cache = <&L2_700>; > + L2_700: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + }; > + > + firmware { > + scm: scm { > + compatible = "qcom,scm-sm8150", "qcom,scm"; > + #reset-cells = <1>; > + }; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x80000000 0x0 0x0>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + soc: soc@0 { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges = <0 0 0 0 0x10 0>; > + dma-ranges = <0 0 0 0 0x10 0>; > + compatible = "simple-bus"; > + > + gcc: clock-controller@100000 { > + compatible = "qcom,gcc-sm8150"; > + reg = <0x0 0x00100000 0x0 0x1f0000>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + clock-names = "bi_tcxo", > + "sleep_clk"; > + clocks = <&rpmhcc RPMH_CXO_CLK>, > + <&sleep_clk>; > + }; > + > + qupv3_id_1: geniqup@ac0000 { > + compatible = "qcom,geni-se-qup"; > + reg = <0x0 0x00ac0000 0x0 0x6000>; > + clock-names = "m-ahb", "s-ahb"; > + clocks = <&gcc 123>, > + <&gcc 124>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + status = "disabled"; > + > + uart2: serial@a90000 { > + compatible = "qcom,geni-debug-uart"; > + reg = <0x0 0x00a90000 0x0 0x4000>; > + clock-names = "se"; > + clocks = <&gcc 105>; > + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + }; > + > + tlmm: pinctrl@3100000 { > + compatible = "qcom,sm8150-pinctrl"; > + reg = <0x0 0x03100000 0x0 0x300000>, > + <0x0 0x03500000 0x0 0x300000>, > + <0x0 0x03900000 0x0 0x300000>, > + <0x0 0x03D00000 0x0 0x300000>; > + reg-names = "west", "east", "north", "south"; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&tlmm 0 0 175>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + spmi_bus: spmi@c440000 { > + compatible = "qcom,spmi-pmic-arb"; > + reg = <0x0 0x0c440000 0x0 0x0001100>, > + <0x0 0x0c600000 0x0 0x2000000>, > + <0x0 0x0e600000 0x0 0x0100000>, > + <0x0 0x0e700000 0x0 0x00a0000>, > + <0x0 0x0c40a000 0x0 0x0026000>; > + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; > + interrupt-names = "periph_irq"; > + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; > + qcom,ee = <0>; > + qcom,channel = <0>; > + #address-cells = <2>; > + #size-cells = <0>; > + interrupt-controller; > + #interrupt-cells = <4>; > + cell-index = <0>; > + }; > + > + intc: interrupt-controller@17a00000 { > + compatible = "arm,gic-v3"; > + interrupt-controller; > + #interrupt-cells = <3>; > + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ > + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + timer@17c20000 { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0 0x17c20000 0x0 0x1000>; > + clock-frequency = <19200000>; > + > + frame@17c21000{ > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c21000 0x0 0x1000>, > + <0x0 0x17c22000 0x0 0x1000>; > + }; > + > + frame@17c23000 { > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c23000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c25000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c25000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c27000 { > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c26000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c29000 { > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c29000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2b000 { > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2b000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2d000 { > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2d000 0x0 0x1000>; > + status = "disabled"; > + }; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, > + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, > + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, > + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > -- > 2.20.1 >
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi new file mode 100644 index 000000000000..417b21d1897c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. + * Copyright (c) 2019, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/clock/qcom,rpmh.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32764>; + clock-output-names = "sleep_clk"; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8150", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x80000000 0x0 0x0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x0 0x00100000 0x0 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>; + }; + + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00ac0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 123>, + <&gcc 124>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart2: serial@a90000 { + compatible = "qcom,geni-debug-uart"; + reg = <0x0 0x00a90000 0x0 0x4000>; + clock-names = "se"; + clocks = <&gcc 105>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + + tlmm: pinctrl@3100000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x0 0x03100000 0x0 0x300000>, + <0x0 0x03500000 0x0 0x300000>, + <0x0 0x03900000 0x0 0x300000>, + <0x0 0x03D00000 0x0 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c440000 0x0 0x0001100>, + <0x0 0x0c600000 0x0 0x2000000>, + <0x0 0x0e600000 0x0 0x0100000>, + <0x0 0x0e700000 0x0 0x00a0000>, + <0x0 0x0c40a000 0x0 0x0026000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + cell-index = <0>; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <2>; + #size-cells = <2>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0 0x17c20000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000{ + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c21000 0x0 0x1000>, + <0x0 0x17c22000 0x0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c23000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c25000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c26000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c29000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2d000 0x0 0x1000>; + status = "disabled"; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; + }; +};