| Message ID | 20190619215156.27795-1-robh@kernel.org |
|---|---|
| State | New |
| Headers | show |
| Series | [RFC,1/4] dt-bindings: display: Convert common panel bindings to DT schema | expand |
Hi Rob. Thanks for starting the conversion of panel bindings to yaml. On Wed, Jun 19, 2019 at 03:51:53PM -0600, Rob Herring wrote: > Convert the common panel bindings to DT schema consolidating scattered > definitions to a single schema file. > > The 'simple-panel' binding just a collection of properties and not a > complete binding itself. All of the 'simple-panel' properties are > covered by the panel-common.txt binding with the exception of the > 'no-hpd' property, so add that to the schema. > > As there are lots of references to simple-panel.txt, just keep the file > with a reference to panel-common.yaml for now until all the bindings are > converted. Good idea. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> > --- > Note there's still some references to panel-common.txt that I need to > update or just go ahead and convert to schema. Better let it point to the .yaml variant, so this patchset does not depend on too much other bindings to be converted. Then we can start the conversion of the remaining panel bindings. Any tooling that helps the conversions? When this hits upstream I assume all future panel bindings shall be yaml based - so we have a few pending contributions that need to do something. For the actual conversion below: Acked-by: Sam Ravnborg <sam@ravnborg.org> Sam > > .../bindings/display/panel/panel-common.txt | 101 ------------- > .../bindings/display/panel/panel-common.yaml | 143 ++++++++++++++++++ > .../bindings/display/panel/panel.txt | 4 - > .../bindings/display/panel/simple-panel.txt | 29 +--- > 4 files changed, 144 insertions(+), 133 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt > create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml > delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt > > diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt > deleted file mode 100644 > index 5d2519af4bb5..000000000000 > --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt > +++ /dev/null > @@ -1,101 +0,0 @@ > -Common Properties for Display Panel > -=================================== > - > -This document defines device tree properties common to several classes of > -display panels. It doesn't constitue a device tree binding specification by > -itself but is meant to be referenced by device tree bindings. > - > -When referenced from panel device tree bindings the properties defined in this > -document are defined as follows. The panel device tree bindings are > -responsible for defining whether each property is required or optional. > - > - > -Descriptive Properties > ----------------------- > - > -- width-mm, > -- height-mm: The width-mm and height-mm specify the width and height of the > - physical area where images are displayed. These properties are expressed in > - millimeters and rounded to the closest unit. > - > -- label: The label property specifies a symbolic name for the panel as a > - string suitable for use by humans. It typically contains a name inscribed on > - the system (e.g. as an affixed label) or specified in the system's > - documentation (e.g. in the user's manual). > - > - If no such name exists, and unless the property is mandatory according to > - device tree bindings, it shall rather be omitted than constructed of > - non-descriptive information. For instance an LCD panel in a system that > - contains a single panel shall not be labelled "LCD" if that name is not > - inscribed on the system or used in a descriptive fashion in system > - documentation. > - > - > -Display Timings > ---------------- > - > -- panel-timing: Most display panels are restricted to a single resolution and > - require specific display timings. The panel-timing subnode expresses those > - timings as specified in the timing subnode section of the display timing > - bindings defined in > - Documentation/devicetree/bindings/display/panel/display-timing.txt. > - > - > -Connectivity > ------------- > - > -- ports: Panels receive video data through one or multiple connections. While > - the nature of those connections is specific to the panel type, the > - connectivity is expressed in a standard fashion using ports as specified in > - the device graph bindings defined in > - Documentation/devicetree/bindings/graph.txt. > - > -- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible > - bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a > - phandle to the system I2C controller connected to that bus. > - > - > -Control I/Os > ------------- > - > -Many display panels can be controlled through pins driven by GPIOs. The nature > -and timing of those control signals are device-specific and left for panel > -device tree bindings to specify. The following GPIO specifiers can however be > -used for panels that implement compatible control signals. > - > -- enable-gpios: Specifier for a GPIO connected to the panel enable control > - signal. The enable signal is active high and enables operation of the panel. > - This property can also be used for panels implementing an active low power > - down signal, which is a negated version of the enable signal. Active low > - enable signals (or active high power down signals) can be supported by > - inverting the GPIO specifier polarity flag. > - > - Note that the enable signal control panel operation only and must not be > - confused with a backlight enable signal. > - > -- reset-gpios: Specifier for a GPIO coonnected to the panel reset control > - signal. The reset signal is active low and resets the panel internal logic > - while active. Active high reset signals can be supported by inverting the > - GPIO specifier polarity flag. > - > -Power > ------ > - > -- power-supply: display panels require power to be supplied. While several > - panels need more than one power supply with panel-specific constraints > - governing the order and timings of the power supplies, in many cases a single > - power supply is sufficient, either because the panel has a single power rail, > - or because all its power rails can be driven by the same supply. In that case > - the power-supply property specifies the supply powering the panel as a phandle > - to a regulator. > - > -Backlight > ---------- > - > -Most display panels include a backlight. Some of them also include a backlight > -controller exposed through a control bus such as I2C or DSI. Others expose > -backlight control through GPIO, PWM or other signals connected to an external > -backlight controller. > - > -- backlight: For panels whose backlight is controlled by an external backlight > - controller, this property contains a phandle that references the controller. > diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml > new file mode 100644 > index 000000000000..6fe87254edad > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml > @@ -0,0 +1,143 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/panel/panel-common.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Common Properties for Display Panels > + > +maintainers: > + - Thierry Reding <thierry.reding@gmail.com> > + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> > + > +description: | > + This document defines device tree properties common to several classes of > + display panels. It doesn't constitue a device tree binding specification by > + itself but is meant to be referenced by device tree bindings. > + > + When referenced from panel device tree bindings the properties defined in this > + document are defined as follows. The panel device tree bindings are > + responsible for defining whether each property is required or optional. > + > + > +properties: > + # Descriptive Properties > + width-mm: > + description: The width-mm and height-mm specify the width and height of the > + physical area where images are displayed. These properties are expressed > + in millimeters and rounded to the closest unit. > + > + height-mm: > + description: The width-mm and height-mm specify the width and height of the > + physical area where images are displayed. These properties are expressed > + in millimeters and rounded to the closest unit. > + > + label: > + description: | > + The label property specifies a symbolic name for the panel as a > + string suitable for use by humans. It typically contains a name inscribed > + on the system (e.g. as an affixed label) or specified in the system's > + documentation (e.g. in the user's manual). > + > + If no such name exists, and unless the property is mandatory according to > + device tree bindings, it shall rather be omitted than constructed of > + non-descriptive information. For instance an LCD panel in a system that > + contains a single panel shall not be labelled "LCD" if that name is not > + inscribed on the system or used in a descriptive fashion in system > + documentation. > + > + rotation: > + description: > + Display rotation in degrees counter clockwise (0,90,180,270) > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - enum: [ 0, 90, 180, 270 ] > + > + # Display Timings > + panel-timing: > + type: object > + description: > + Most display panels are restricted to a single resolution and > + require specific display timings. The panel-timing subnode expresses those > + timings as specified in the timing subnode section of the display timing > + bindings defined in > + Documentation/devicetree/bindings/display/panel/display-timing.txt. > + > + # Connectivity > + ports: > + type: object > + description: > + Panels receive video data through one or multiple connections. While > + the nature of those connections is specific to the panel type, the > + connectivity is expressed in a standard fashion using ports as specified > + in the device graph bindings defined in > + Documentation/devicetree/bindings/graph.txt. > + > + ddc-i2c-bus: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + Some panels expose EDID information through an I2C-compatible > + bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a > + phandle to the system I2C controller connected to that bus. > + > + no-hpd: > + type: boolean > + description: > + This panel is supposed to communicate that it's ready via HPD > + (hot plug detect) signal, but the signal isn't hooked up so we should > + hardcode the max delay from the panel spec when powering up the panel. > + > + # Control I/Os > + > + # Many display panels can be controlled through pins driven by GPIOs. The nature > + # and timing of those control signals are device-specific and left for panel > + # device tree bindings to specify. The following GPIO specifiers can however be > + # used for panels that implement compatible control signals. > + > + enable-gpios: > + maxItems: 1 > + description: | > + Specifier for a GPIO connected to the panel enable control signal. The > + enable signal is active high and enables operation of the panel. This > + property can also be used for panels implementing an active low power down > + signal, which is a negated version of the enable signal. Active low enable > + signals (or active high power down signals) can be supported by inverting > + the GPIO specifier polarity flag. > + > + Note that the enable signal control panel operation only and must not be > + confused with a backlight enable signal. > + > + reset-gpios: > + maxItems: 1 > + description: > + Specifier for a GPIO coonnected to the panel reset control signal. > + The reset signal is active low and resets the panel internal logic > + while active. Active high reset signals can be supported by inverting the > + GPIO specifier polarity flag. > + > + # Power > + power-supply: > + description: > + Display panels require power to be supplied. While several panels need > + more than one power supply with panel-specific constraints governing the > + order and timings of the power supplies, in many cases a single power > + supply is sufficient, either because the panel has a single power rail, or > + because all its power rails can be driven by the same supply. In that case > + the power-supply property specifies the supply powering the panel as a > + phandle to a regulator. > + > + # Backlight > + > + # Most display panels include a backlight. Some of them also include a backlight > + # controller exposed through a control bus such as I2C or DSI. Others expose > + # backlight control through GPIO, PWM or other signals connected to an external > + # backlight controller. > + > + backlight: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + For panels whose backlight is controlled by an external backlight > + controller, this property contains a phandle that references the > + controller. > + > +... > diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt > deleted file mode 100644 > index e2e6867852b8..000000000000 > --- a/Documentation/devicetree/bindings/display/panel/panel.txt > +++ /dev/null > @@ -1,4 +0,0 @@ > -Common display properties > -------------------------- > - > -- rotation: Display rotation in degrees counter clockwise (0,90,180,270) > diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > index b2b872c710f2..e11208fb7da8 100644 > --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt > +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > @@ -1,28 +1 @@ > -Simple display panel > -==================== > - > -panel node > ----------- > - > -Required properties: > -- power-supply: See panel-common.txt > - > -Optional properties: > -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing > -- enable-gpios: GPIO pin to enable or disable the panel > -- backlight: phandle of the backlight device attached to the panel > -- no-hpd: This panel is supposed to communicate that it's ready via HPD > - (hot plug detect) signal, but the signal isn't hooked up so we should > - hardcode the max delay from the panel spec when powering up the panel. > - > -Example: > - > - panel: panel { > - compatible = "cptt,claa101wb01"; > - ddc-i2c-bus = <&panelddc>; > - > - power-supply = <&vdd_pnl_reg>; > - enable-gpios = <&gpio 90 0>; > - > - backlight = <&backlight>; > - }; > +See panel-common.yaml in this directory. > -- > 2.20.1 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Wed, Jun 19, 2019 at 03:51:53PM -0600, Rob Herring wrote: > Convert the common panel bindings to DT schema consolidating scattered > definitions to a single schema file. > > The 'simple-panel' binding just a collection of properties and not a > complete binding itself. All of the 'simple-panel' properties are > covered by the panel-common.txt binding with the exception of the > 'no-hpd' property, so add that to the schema. > > As there are lots of references to simple-panel.txt, just keep the file > with a reference to panel-common.yaml for now until all the bindings are > converted. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com> Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
On Wed, Jun 19, 2019 at 03:51:54PM -0600, Rob Herring wrote: > Convert the ampire,am-480272h3tmqw-t01h panel binding to DT schema. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com> Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
On Wed, Jun 19, 2019 at 03:51:56PM -0600, Rob Herring wrote: > Convert the innolux,ee101ia-01 LVDS panel binding to DT schema. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com> Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
On Wed, Jun 19, 2019 at 03:51:54PM -0600, Rob Herring wrote: > Convert the ampire,am-480272h3tmqw-t01h panel binding to DT schema. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> > --- > .../panel/ampire,am-480272h3tmqw-t01h.txt | 26 ------------ > .../panel/ampire,am-480272h3tmqw-t01h.yaml | 41 +++++++++++++++++++ > 2 files changed, 41 insertions(+), 26 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt > create mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml Acked-by: Thierry Reding <treding@nvidia.com>
On Wed, Jun 19, 2019 at 03:51:55PM -0600, Rob Herring wrote: > Convert the panel-lvds binding to use DT schema. The panel-lvds schema > inherits from the panel-common.yaml schema and specific LVDS panel > bindings should inherit from this schema. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> > --- > .../bindings/display/panel/panel-lvds.txt | 121 ------------------ > .../bindings/display/panel/panel-lvds.yaml | 107 ++++++++++++++++ > 2 files changed, 107 insertions(+), 121 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-lvds.txt > create mode 100644 Documentation/devicetree/bindings/display/panel/panel-lvds.yaml Similar to my comments on panel-common.yaml, perhaps make this just lvds.yaml? Otherwise: Acked-by: Thierry Reding <treding@nvidia.com>
On Wed, Jun 19, 2019 at 03:51:56PM -0600, Rob Herring wrote: > Convert the innolux,ee101ia-01 LVDS panel binding to DT schema. > > Cc: Thierry Reding <thierry.reding@gmail.com> > Cc: Sam Ravnborg <sam@ravnborg.org> > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Cc: dri-devel@lists.freedesktop.org > Signed-off-by: Rob Herring <robh@kernel.org> > --- > .../display/panel/innolux,ee101ia-01d.txt | 7 ------- > .../display/panel/innolux,ee101ia-01d.yaml | 21 +++++++++++++++++++ > 2 files changed, 21 insertions(+), 7 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt > create mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml Acked-by: Thierry Reding <treding@nvidia.com>
On Thu, Jun 20, 2019 at 3:01 AM Thierry Reding <thierry.reding@gmail.com> wrote: > > On Wed, Jun 19, 2019 at 03:51:53PM -0600, Rob Herring wrote: > > Convert the common panel bindings to DT schema consolidating scattered > > definitions to a single schema file. > > > > The 'simple-panel' binding just a collection of properties and not a > > complete binding itself. All of the 'simple-panel' properties are > > covered by the panel-common.txt binding with the exception of the > > 'no-hpd' property, so add that to the schema. > > > > As there are lots of references to simple-panel.txt, just keep the file > > with a reference to panel-common.yaml for now until all the bindings are > > converted. > > > > Cc: Thierry Reding <thierry.reding@gmail.com> > > Cc: Sam Ravnborg <sam@ravnborg.org> > > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Cc: dri-devel@lists.freedesktop.org > > Signed-off-by: Rob Herring <robh@kernel.org> > > --- > > Note there's still some references to panel-common.txt that I need to > > update or just go ahead and convert to schema. > > > > .../bindings/display/panel/panel-common.txt | 101 ------------- > > .../bindings/display/panel/panel-common.yaml | 143 ++++++++++++++++++ > > .../bindings/display/panel/panel.txt | 4 - > > .../bindings/display/panel/simple-panel.txt | 29 +--- > > 4 files changed, 144 insertions(+), 133 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt > > create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml > > I know it was this way before, but perhaps remove the redundant panel- > prefix while at it? Sure. > > diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml > > new file mode 100644 > > index 000000000000..6fe87254edad > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml > > @@ -0,0 +1,143 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/display/panel/panel-common.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Common Properties for Display Panels > > + > > +maintainers: > > + - Thierry Reding <thierry.reding@gmail.com> > > + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> > > + > > +description: | > > + This document defines device tree properties common to several classes of > > + display panels. It doesn't constitue a device tree binding specification by > > + itself but is meant to be referenced by device tree bindings. > > + > > + When referenced from panel device tree bindings the properties defined in this > > + document are defined as follows. The panel device tree bindings are > > + responsible for defining whether each property is required or optional. > > + > > + > > Are the two blank lines here on purpose? No. > The original document had two > blank lines here, but that was mostly for readability I would guess. The > YAML format doesn't really need additional formatting for readability, > so perhaps just remove the extra blank line? > > > +properties: > > + # Descriptive Properties > > + width-mm: > > + description: The width-mm and height-mm specify the width and height of the > > + physical area where images are displayed. These properties are expressed > > + in millimeters and rounded to the closest unit. > > + > > + height-mm: > > + description: The width-mm and height-mm specify the width and height of the > > + physical area where images are displayed. These properties are expressed > > + in millimeters and rounded to the closest unit. > > I suppose there's no way in YAML to share the description between both > the width-mm and height-mm properties? It's a little unfortunate that we > have to copy, but if there's no better way, guess we'll have to live > with it. I could make it a comment instead, but then we loose being able to parse it. I should probably just reword them to be separate: "Specifies the height of the physical area where images are displayed. The property is expressed in millimeters and rounded to the closest unit." Also, just realized I need to make these 2 dependencies on either other (i.e. not valid to only have one). > > + label: > > + description: | > > + The label property specifies a symbolic name for the panel as a > > + string suitable for use by humans. It typically contains a name inscribed > > + on the system (e.g. as an affixed label) or specified in the system's > > + documentation (e.g. in the user's manual). > > + > > + If no such name exists, and unless the property is mandatory according to > > + device tree bindings, it shall rather be omitted than constructed of > > + non-descriptive information. For instance an LCD panel in a system that > > + contains a single panel shall not be labelled "LCD" if that name is not > > + inscribed on the system or used in a descriptive fashion in system > > + documentation. > > + > > + rotation: > > + description: > > + Display rotation in degrees counter clockwise (0,90,180,270) > > + allOf: > > + - $ref: /schemas/types.yaml#/definitions/uint32 > > + - enum: [ 0, 90, 180, 270 ] > > + > > + # Display Timings > > + panel-timing: > > Am I the only one bugged by the redundancy in this property name? What > else is the timing going to express if not the timing of the panel that > it's part of. "timing" really would be enough. Anyway, not much we can > do about it now. I'm just happy we have a defined name. Rob
On Thu, Jun 20, 2019 at 12:55 AM Sam Ravnborg <sam@ravnborg.org> wrote: > > Hi Rob. > > Thanks for starting the conversion of panel bindings to yaml. > > On Wed, Jun 19, 2019 at 03:51:53PM -0600, Rob Herring wrote: > > Convert the common panel bindings to DT schema consolidating scattered > > definitions to a single schema file. > > > > The 'simple-panel' binding just a collection of properties and not a > > complete binding itself. All of the 'simple-panel' properties are > > covered by the panel-common.txt binding with the exception of the > > 'no-hpd' property, so add that to the schema. > > > > As there are lots of references to simple-panel.txt, just keep the file > > with a reference to panel-common.yaml for now until all the bindings are > > converted. > Good idea. > > > > > Cc: Thierry Reding <thierry.reding@gmail.com> > > Cc: Sam Ravnborg <sam@ravnborg.org> > > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Cc: dri-devel@lists.freedesktop.org > > Signed-off-by: Rob Herring <robh@kernel.org> > > --- > > Note there's still some references to panel-common.txt that I need to > > update or just go ahead and convert to schema. > Better let it point to the .yaml variant, so this patchset does not > depend on too much other bindings to be converted. There's only 8 files referencing panel-common.txt which was why I was debating just converting all of them. > Then we can start the conversion of the remaining panel bindings. > Any tooling that helps the conversions? I have a doc2yaml script that helps with some of the boilerplate. It's in my yaml-bindings-v2 branch[1]. > When this hits upstream I assume all future panel bindings shall be yaml > based - so we have a few pending contributions that need to do something. That would be ideal, but not strictly required. For pending things, no reason to make folks redo things. Requiring schema really depends on whomever is applying things to run at least 'make dt_binding_check' before accepting. > > For the actual conversion below: > Acked-by: Sam Ravnborg <sam@ravnborg.org> Thanks. Rob [1] https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/log/?h=yaml-bindings-v2
On Thu, Jun 20, 2019 at 8:52 AM Rob Herring <robh@kernel.org> wrote: > > On Thu, Jun 20, 2019 at 3:01 AM Thierry Reding <thierry.reding@gmail.com> wrote: > > > > On Wed, Jun 19, 2019 at 03:51:53PM -0600, Rob Herring wrote: > > > Convert the common panel bindings to DT schema consolidating scattered > > > definitions to a single schema file. > > > > > > The 'simple-panel' binding just a collection of properties and not a > > > complete binding itself. All of the 'simple-panel' properties are > > > covered by the panel-common.txt binding with the exception of the > > > 'no-hpd' property, so add that to the schema. > > > > > > As there are lots of references to simple-panel.txt, just keep the file > > > with a reference to panel-common.yaml for now until all the bindings are > > > converted. > > > > > > Cc: Thierry Reding <thierry.reding@gmail.com> > > > Cc: Sam Ravnborg <sam@ravnborg.org> > > > Cc: Maxime Ripard <maxime.ripard@bootlin.com> > > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > > Cc: dri-devel@lists.freedesktop.org > > > Signed-off-by: Rob Herring <robh@kernel.org> > > > --- > > > Note there's still some references to panel-common.txt that I need to > > > update or just go ahead and convert to schema. > > > > > > .../bindings/display/panel/panel-common.txt | 101 ------------- > > > .../bindings/display/panel/panel-common.yaml | 143 ++++++++++++++++++ > > > .../bindings/display/panel/panel.txt | 4 - > > > .../bindings/display/panel/simple-panel.txt | 29 +--- > > > 4 files changed, 144 insertions(+), 133 deletions(-) > > > delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt > > > create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml > > > > I know it was this way before, but perhaps remove the redundant panel- > > prefix while at it? > > Sure. On 2nd thought, I prefer it as-is. The reason being the schema including this file are more readable with: allOf: - $ref: panel-common.yaml# Compared to one of: $ref: common.yaml# $ref: /schemas/display/panel/common.yaml# I suppose we could automagically include a 'common.yaml' file if existing in the same directory. That's a bigger change though... Rob
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt deleted file mode 100644 index 5d2519af4bb5..000000000000 --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt +++ /dev/null @@ -1,101 +0,0 @@ -Common Properties for Display Panel -=================================== - -This document defines device tree properties common to several classes of -display panels. It doesn't constitue a device tree binding specification by -itself but is meant to be referenced by device tree bindings. - -When referenced from panel device tree bindings the properties defined in this -document are defined as follows. The panel device tree bindings are -responsible for defining whether each property is required or optional. - - -Descriptive Properties ----------------------- - -- width-mm, -- height-mm: The width-mm and height-mm specify the width and height of the - physical area where images are displayed. These properties are expressed in - millimeters and rounded to the closest unit. - -- label: The label property specifies a symbolic name for the panel as a - string suitable for use by humans. It typically contains a name inscribed on - the system (e.g. as an affixed label) or specified in the system's - documentation (e.g. in the user's manual). - - If no such name exists, and unless the property is mandatory according to - device tree bindings, it shall rather be omitted than constructed of - non-descriptive information. For instance an LCD panel in a system that - contains a single panel shall not be labelled "LCD" if that name is not - inscribed on the system or used in a descriptive fashion in system - documentation. - - -Display Timings ---------------- - -- panel-timing: Most display panels are restricted to a single resolution and - require specific display timings. The panel-timing subnode expresses those - timings as specified in the timing subnode section of the display timing - bindings defined in - Documentation/devicetree/bindings/display/panel/display-timing.txt. - - -Connectivity ------------- - -- ports: Panels receive video data through one or multiple connections. While - the nature of those connections is specific to the panel type, the - connectivity is expressed in a standard fashion using ports as specified in - the device graph bindings defined in - Documentation/devicetree/bindings/graph.txt. - -- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible - bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a - phandle to the system I2C controller connected to that bus. - - -Control I/Os ------------- - -Many display panels can be controlled through pins driven by GPIOs. The nature -and timing of those control signals are device-specific and left for panel -device tree bindings to specify. The following GPIO specifiers can however be -used for panels that implement compatible control signals. - -- enable-gpios: Specifier for a GPIO connected to the panel enable control - signal. The enable signal is active high and enables operation of the panel. - This property can also be used for panels implementing an active low power - down signal, which is a negated version of the enable signal. Active low - enable signals (or active high power down signals) can be supported by - inverting the GPIO specifier polarity flag. - - Note that the enable signal control panel operation only and must not be - confused with a backlight enable signal. - -- reset-gpios: Specifier for a GPIO coonnected to the panel reset control - signal. The reset signal is active low and resets the panel internal logic - while active. Active high reset signals can be supported by inverting the - GPIO specifier polarity flag. - -Power ------ - -- power-supply: display panels require power to be supplied. While several - panels need more than one power supply with panel-specific constraints - governing the order and timings of the power supplies, in many cases a single - power supply is sufficient, either because the panel has a single power rail, - or because all its power rails can be driven by the same supply. In that case - the power-supply property specifies the supply powering the panel as a phandle - to a regulator. - -Backlight ---------- - -Most display panels include a backlight. Some of them also include a backlight -controller exposed through a control bus such as I2C or DSI. Others expose -backlight control through GPIO, PWM or other signals connected to an external -backlight controller. - -- backlight: For panels whose backlight is controlled by an external backlight - controller, this property contains a phandle that references the controller. diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml new file mode 100644 index 000000000000..6fe87254edad --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml @@ -0,0 +1,143 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Display Panels + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + +description: | + This document defines device tree properties common to several classes of + display panels. It doesn't constitue a device tree binding specification by + itself but is meant to be referenced by device tree bindings. + + When referenced from panel device tree bindings the properties defined in this + document are defined as follows. The panel device tree bindings are + responsible for defining whether each property is required or optional. + + +properties: + # Descriptive Properties + width-mm: + description: The width-mm and height-mm specify the width and height of the + physical area where images are displayed. These properties are expressed + in millimeters and rounded to the closest unit. + + height-mm: + description: The width-mm and height-mm specify the width and height of the + physical area where images are displayed. These properties are expressed + in millimeters and rounded to the closest unit. + + label: + description: | + The label property specifies a symbolic name for the panel as a + string suitable for use by humans. It typically contains a name inscribed + on the system (e.g. as an affixed label) or specified in the system's + documentation (e.g. in the user's manual). + + If no such name exists, and unless the property is mandatory according to + device tree bindings, it shall rather be omitted than constructed of + non-descriptive information. For instance an LCD panel in a system that + contains a single panel shall not be labelled "LCD" if that name is not + inscribed on the system or used in a descriptive fashion in system + documentation. + + rotation: + description: + Display rotation in degrees counter clockwise (0,90,180,270) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 90, 180, 270 ] + + # Display Timings + panel-timing: + type: object + description: + Most display panels are restricted to a single resolution and + require specific display timings. The panel-timing subnode expresses those + timings as specified in the timing subnode section of the display timing + bindings defined in + Documentation/devicetree/bindings/display/panel/display-timing.txt. + + # Connectivity + ports: + type: object + description: + Panels receive video data through one or multiple connections. While + the nature of those connections is specific to the panel type, the + connectivity is expressed in a standard fashion using ports as specified + in the device graph bindings defined in + Documentation/devicetree/bindings/graph.txt. + + ddc-i2c-bus: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some panels expose EDID information through an I2C-compatible + bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a + phandle to the system I2C controller connected to that bus. + + no-hpd: + type: boolean + description: + This panel is supposed to communicate that it's ready via HPD + (hot plug detect) signal, but the signal isn't hooked up so we should + hardcode the max delay from the panel spec when powering up the panel. + + # Control I/Os + + # Many display panels can be controlled through pins driven by GPIOs. The nature + # and timing of those control signals are device-specific and left for panel + # device tree bindings to specify. The following GPIO specifiers can however be + # used for panels that implement compatible control signals. + + enable-gpios: + maxItems: 1 + description: | + Specifier for a GPIO connected to the panel enable control signal. The + enable signal is active high and enables operation of the panel. This + property can also be used for panels implementing an active low power down + signal, which is a negated version of the enable signal. Active low enable + signals (or active high power down signals) can be supported by inverting + the GPIO specifier polarity flag. + + Note that the enable signal control panel operation only and must not be + confused with a backlight enable signal. + + reset-gpios: + maxItems: 1 + description: + Specifier for a GPIO coonnected to the panel reset control signal. + The reset signal is active low and resets the panel internal logic + while active. Active high reset signals can be supported by inverting the + GPIO specifier polarity flag. + + # Power + power-supply: + description: + Display panels require power to be supplied. While several panels need + more than one power supply with panel-specific constraints governing the + order and timings of the power supplies, in many cases a single power + supply is sufficient, either because the panel has a single power rail, or + because all its power rails can be driven by the same supply. In that case + the power-supply property specifies the supply powering the panel as a + phandle to a regulator. + + # Backlight + + # Most display panels include a backlight. Some of them also include a backlight + # controller exposed through a control bus such as I2C or DSI. Others expose + # backlight control through GPIO, PWM or other signals connected to an external + # backlight controller. + + backlight: + $ref: /schemas/types.yaml#/definitions/phandle + description: + For panels whose backlight is controlled by an external backlight + controller, this property contains a phandle that references the + controller. + +... diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt deleted file mode 100644 index e2e6867852b8..000000000000 --- a/Documentation/devicetree/bindings/display/panel/panel.txt +++ /dev/null @@ -1,4 +0,0 @@ -Common display properties -------------------------- - -- rotation: Display rotation in degrees counter clockwise (0,90,180,270) diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt index b2b872c710f2..e11208fb7da8 100644 --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt @@ -1,28 +1 @@ -Simple display panel -==================== - -panel node ----------- - -Required properties: -- power-supply: See panel-common.txt - -Optional properties: -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing -- enable-gpios: GPIO pin to enable or disable the panel -- backlight: phandle of the backlight device attached to the panel -- no-hpd: This panel is supposed to communicate that it's ready via HPD - (hot plug detect) signal, but the signal isn't hooked up so we should - hardcode the max delay from the panel spec when powering up the panel. - -Example: - - panel: panel { - compatible = "cptt,claa101wb01"; - ddc-i2c-bus = <&panelddc>; - - power-supply = <&vdd_pnl_reg>; - enable-gpios = <&gpio 90 0>; - - backlight = <&backlight>; - }; +See panel-common.yaml in this directory.
Convert the common panel bindings to DT schema consolidating scattered definitions to a single schema file. The 'simple-panel' binding just a collection of properties and not a complete binding itself. All of the 'simple-panel' properties are covered by the panel-common.txt binding with the exception of the 'no-hpd' property, so add that to the schema. As there are lots of references to simple-panel.txt, just keep the file with a reference to panel-common.yaml for now until all the bindings are converted. Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Rob Herring <robh@kernel.org> --- Note there's still some references to panel-common.txt that I need to update or just go ahead and convert to schema. .../bindings/display/panel/panel-common.txt | 101 ------------- .../bindings/display/panel/panel-common.yaml | 143 ++++++++++++++++++ .../bindings/display/panel/panel.txt | 4 - .../bindings/display/panel/simple-panel.txt | 29 +--- 4 files changed, 144 insertions(+), 133 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt -- 2.20.1