diff mbox

[V9,6/9] SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT

Message ID 1367043180-6756-7-git-send-email-amarendra.xt@samsung.com
State Accepted
Commit 752f4c4a9c232bba6f27a70db587aebd3dd6bb3f
Headers show

Commit Message

Amar April 27, 2013, 6:12 a.m. UTC
From: Amar <amarendra.xt@samsung.com>

This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
        exynos5-dt.c:   This file shall contain all code which supports FDT.
                        Any addition of FDT support for any module needs to be
                        added in this file.
        smdk5250.c:     This file shall contain the code which supports non-FDT.
                        version. Any addition of non-FDT support for any module
                        needs to be added in this file.
                        May be, the file smdk5250.c can be removed in near future
                        when non-FDT is not required.

The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.

NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.

Signed-off-by: Amar <amarendra.xt@samsung.com>
---
Changes since V1:
	1)A new file 'exynos5-dt.c' is created meant for FDT support
	2)Makefile is updated to compile only one of the files
	exynos5-dt.c / smdk5250.c based on FDT configuration

Changes since V2:
	1)Updation of commit message and resubmition of proper patch set.

Changes since V3:
	No change.

Changes since V4:
	1)Replaced the function call 'exynos_dwmmc_init(0, 8);' with the
	function exynos_dwmmc_add_port() in smdk5250.c.
	2)dram_init() is updated to use for loop to compute the ram size.
	3)dram_init_banksize() is updated to use for loop to initialise
	the dram bank size.
	4)board_uart_init() is updated to use for loop to initialise UARTS.
	5)In non-FDT case NULL is passed as parameter to board_i2c_init().

Changes since V5:
	1)Enabled CONFIG_LCD only for non-FDT operation.

Changes since V6:
	1)Re-based.

Changes since V7:
	1)Re-based.
	2)Because of creation of new file 'exynos5-dt.c' meant for FDT support,
	 the exynos_fb.c had to be updated to support non-FDT and FDT for LCD. 
	 If exynos_fb.c is not updated as per this patch the compilation fails.
	3)Added the macro CONFIG_SUPPORT_EMMC_BOOT in exynos5250-dt.h.

Changes since V7:
	No change.

Changes since V8:
	No change.

 board/samsung/smdk5250/Makefile     |   4 +
 board/samsung/smdk5250/exynos5-dt.c | 423 ++++++++++++++++++++++++++++++++++++
 board/samsung/smdk5250/smdk5250.c   | 223 +++++--------------
 drivers/video/exynos_fb.c           |   4 +-
 include/configs/exynos5250-dt.h     |   8 +
 5 files changed, 493 insertions(+), 169 deletions(-)
 create mode 100644 board/samsung/smdk5250/exynos5-dt.c
diff mbox

Patch

diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
index 47c6a5a..ecca9f3 100644
--- a/board/samsung/smdk5250/Makefile
+++ b/board/samsung/smdk5250/Makefile
@@ -32,8 +32,12 @@  COBJS	+= tzpc_init.o
 COBJS	+= smdk5250_spl.o
 
 ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_OF_CONTROL
+COBJS	+= exynos5-dt.o
+else
 COBJS	+= smdk5250.o
 endif
+endif
 
 ifdef CONFIG_SPL_BUILD
 COBJS	+= spl_boot.o
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
new file mode 100644
index 0000000..78ef424
--- /dev/null
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -0,0 +1,423 @@ 
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <spi.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/arch/sromc.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <tmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined CONFIG_EXYNOS_TMU
+/*
+ * Boot Time Thermal Analysis for SoC temperature threshold breach
+ */
+static void boot_temp_check(void)
+{
+	int temp;
+
+	switch (tmu_monitor(&temp)) {
+	/* Status TRIPPED ans WARNING means corresponding threshold breach */
+	case TMU_STATUS_TRIPPED:
+		puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
+		set_ps_hold_ctrl();
+		hang();
+		break;
+	case TMU_STATUS_WARNING:
+		puts("EXYNOS_TMU: WARNING! Temperature very high\n");
+		break;
+	/*
+	 * TMU_STATUS_INIT means something is wrong with temperature sensing
+	 * and TMU status was changed back from NORMAL to INIT.
+	 */
+	case TMU_STATUS_INIT:
+	default:
+		debug("EXYNOS_TMU: Unknown TMU state\n");
+	}
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_EXYNOS
+int board_usb_vbus_init(void)
+{
+	struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+						samsung_get_base_gpio_part1();
+
+	/* Enable VBUS power switch */
+	s5p_gpio_direction_output(&gpio1->x2, 6, 1);
+
+	/* VBUS turn ON time */
+	mdelay(3);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SOUND_MAX98095
+static void  board_enable_audio_codec(void)
+{
+	struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+						samsung_get_base_gpio_part1();
+
+	/* Enable MAX98095 Codec */
+	s5p_gpio_direction_output(&gpio1->x1, 7, 1);
+	s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE);
+}
+#endif
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+
+#if defined CONFIG_EXYNOS_TMU
+	if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
+		debug("%s: Failed to init TMU\n", __func__);
+		return -1;
+	}
+	boot_temp_check();
+#endif
+
+#ifdef CONFIG_EXYNOS_SPI
+	spi_init();
+#endif
+#ifdef CONFIG_USB_EHCI_EXYNOS
+	board_usb_vbus_init();
+#endif
+#ifdef CONFIG_SOUND_MAX98095
+	board_enable_audio_codec();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	int i;
+	u32 addr;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+	}
+	return 0;
+}
+
+#if defined(CONFIG_POWER)
+static int pmic_reg_update(struct pmic *p, int reg, uint regval)
+{
+	u32 val;
+	int ret = 0;
+
+	ret = pmic_reg_read(p, reg, &val);
+	if (ret) {
+		debug("%s: PMIC %d register read failed\n", __func__, reg);
+		return -1;
+	}
+	val |= regval;
+	ret = pmic_reg_write(p, reg, val);
+	if (ret) {
+		debug("%s: PMIC %d register write failed\n", __func__, reg);
+		return -1;
+	}
+	return 0;
+}
+
+int power_init_board(void)
+{
+	struct pmic *p;
+
+	set_ps_hold_ctrl();
+
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+	if (pmic_init(I2C_PMIC))
+		return -1;
+
+	p = pmic_get("MAX77686_PMIC");
+	if (!p)
+		return -ENODEV;
+
+	if (pmic_probe(p))
+		return -1;
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN))
+		return -1;
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT,
+			    MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V))
+		return -1;
+
+	/* VDD_MIF */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT,
+			   MAX77686_BUCK1OUT_1V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK1OUT);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL,
+			    MAX77686_BUCK1CTRL_EN))
+		return -1;
+
+	/* VDD_ARM */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1,
+			   MAX77686_BUCK2DVS1_1_3V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK2DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1,
+			    MAX77686_BUCK2CTRL_ON))
+		return -1;
+
+	/* VDD_INT */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1,
+			   MAX77686_BUCK3DVS1_1_0125V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK3DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL,
+			    MAX77686_BUCK3CTRL_ON))
+		return -1;
+
+	/* VDD_G3D */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1,
+			   MAX77686_BUCK4DVS1_1_2V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK4DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1,
+			    MAX77686_BUCK3CTRL_ON))
+		return -1;
+
+	/* VDD_LDO2 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1,
+			    MAX77686_LD02CTRL1_1_5V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO3 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1,
+			    MAX77686_LD03CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO5 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1,
+			    MAX77686_LD05CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO10 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1,
+			    MAX77686_LD10CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	return 0;
+}
+#endif
+
+void dram_init_banksize(void)
+{
+	int i;
+	u32 addr, size;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+		gd->bd->bi_dram[i].start = addr;
+		gd->bd->bi_dram[i].size = size;
+	}
+}
+
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+	int err;
+	int node;
+
+	node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+	if (node < 0) {
+		debug("Could not find SROMC node\n");
+		return node;
+	}
+
+	config->bank = fdtdec_get_int(blob, node, "bank", 0);
+	config->width = fdtdec_get_int(blob, node, "width", 2);
+
+	err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+			FDT_SROM_TIMING_COUNT);
+	if (err < 0) {
+		debug("Could not decode SROMC configuration Error: %s\n",
+		      fdt_strerror(err));
+		return -FDT_ERR_NOTFOUND;
+	}
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+	u32 smc_bw_conf, smc_bc_conf;
+	struct fdt_sromc config;
+	fdt_addr_t base_addr;
+	int node;
+
+	node = decode_sromc(gd->fdt_blob, &config);
+	if (node < 0) {
+		debug("%s: Could not find sromc configuration\n", __func__);
+		return 0;
+	}
+	node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+	if (node < 0) {
+		debug("%s: Could not find lan9215 configuration\n", __func__);
+		return 0;
+	}
+
+	/* We now have a node, so any problems from now on are errors */
+	base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+	if (base_addr == FDT_ADDR_T_NONE) {
+		debug("%s: Could not find lan9215 address\n", __func__);
+		return -1;
+	}
+
+	/* Ethernet needs data bus width of 16 bits */
+	if (config.width != 2) {
+		debug("%s: Unsupported bus width %d\n", __func__,
+		      config.width);
+		return -1;
+	}
+	smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+			| SROMC_BYTE_ENABLE(config.bank);
+
+	smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS])   |
+			SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
+			SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
+			SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
+			SROMC_BC_TAH(config.timing[FDT_SROM_TAH])   |
+			SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
+			SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+	/* Select and configure the SROMC bank */
+	exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+	s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+	return smc911x_initialize(0, base_addr);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	const char *board_name;
+
+	board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+	if (board_name == NULL)
+		printf("\nUnknown Board\n");
+	else
+		printf("\nBoard: %s\n", board_name);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+	/* dwmmc initializattion for available channels */
+	ret = exynos_dwmmc_init(gd->fdt_blob);
+	if (ret)
+		debug("dwmmc init failed\n");
+
+	return ret;
+}
+#endif
+
+static int board_uart_init(void)
+{
+	int err, uart_id, ret = 0;
+
+	for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+		err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+		if (err) {
+			debug("UART%d not configured\n",
+			      (uart_id - PERIPH_ID_UART0));
+			ret |= err;
+		}
+	}
+	return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+	int err;
+	err = board_uart_init();
+	if (err) {
+		debug("UART init failed\n");
+		return err;
+	}
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+	board_i2c_init(gd->fdt_blob);
+#endif
+	return err;
+}
+#endif
+
+#ifdef CONFIG_LCD
+void exynos_cfg_lcd_gpio(void)
+{
+	struct exynos5_gpio_part1 *gpio1 =
+		(struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
+
+	/* For Backlight */
+	s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->b2, 0, 1);
+
+	/* LCD power on */
+	s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->x1, 5, 1);
+
+	/* Set Hotplug detect for DP */
+	s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
+}
+
+void exynos_set_dp_phy(unsigned int onoff)
+{
+	set_dp_phy_ctrl(onoff);
+}
+#endif
diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
index 8b09e1d..276fd41 100644
--- a/board/samsung/smdk5250/smdk5250.c
+++ b/board/samsung/smdk5250/smdk5250.c
@@ -29,6 +29,7 @@ 
 #include <netdev.h>
 #include <spi.h>
 #include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc.h>
 #include <asm/arch/pinmux.h>
@@ -37,39 +38,9 @@ 
 #include <asm/arch/dp_info.h>
 #include <power/pmic.h>
 #include <power/max77686_pmic.h>
-#include <tmu.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#if defined CONFIG_EXYNOS_TMU
-/*
- * Boot Time Thermal Analysis for SoC temperature threshold breach
- */
-static void boot_temp_check(void)
-{
-	int temp;
-
-	switch (tmu_monitor(&temp)) {
-	/* Status TRIPPED ans WARNING means corresponding threshold breach */
-	case TMU_STATUS_TRIPPED:
-		puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
-		set_ps_hold_ctrl();
-		hang();
-		break;
-	case TMU_STATUS_WARNING:
-		puts("EXYNOS_TMU: WARNING! Temperature very high\n");
-		break;
-	/*
-	 * TMU_STATUS_INIT means something is wrong with temperature sensing
-	 * and TMU status was changed back from NORMAL to INIT.
-	 */
-	case TMU_STATUS_INIT:
-	default:
-		debug("EXYNOS_TMU: Unknown TMU state\n");
-	}
-}
-#endif
-
 #ifdef CONFIG_USB_EHCI_EXYNOS
 int board_usb_vbus_init(void)
 {
@@ -102,14 +73,6 @@  int board_init(void)
 {
 	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
 
-#if defined CONFIG_EXYNOS_TMU
-	if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
-		debug("%s: Failed to init TMU\n", __func__);
-		return -1;
-	}
-	boot_temp_check();
-#endif
-
 #ifdef CONFIG_EXYNOS_SPI
 	spi_init();
 #endif
@@ -124,14 +87,13 @@  int board_init(void)
 
 int dram_init(void)
 {
-	gd->ram_size	= get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE)
-			+ get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE);
+	int i;
+	u32 addr;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+	}
 	return 0;
 }
 
@@ -254,57 +216,15 @@  int power_init_board(void)
 
 void dram_init_banksize(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
-							PHYS_SDRAM_1_SIZE);
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2,
-							PHYS_SDRAM_2_SIZE);
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3,
-							PHYS_SDRAM_3_SIZE);
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4,
-							PHYS_SDRAM_4_SIZE);
-	gd->bd->bi_dram[4].start = PHYS_SDRAM_5;
-	gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5,
-							PHYS_SDRAM_5_SIZE);
-	gd->bd->bi_dram[5].start = PHYS_SDRAM_6;
-	gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6,
-							PHYS_SDRAM_6_SIZE);
-	gd->bd->bi_dram[6].start = PHYS_SDRAM_7;
-	gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7,
-							PHYS_SDRAM_7_SIZE);
-	gd->bd->bi_dram[7].start = PHYS_SDRAM_8;
-	gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8,
-							PHYS_SDRAM_8_SIZE);
-}
-
-#ifdef CONFIG_OF_CONTROL
-static int decode_sromc(const void *blob, struct fdt_sromc *config)
-{
-	int err;
-	int node;
-
-	node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
-	if (node < 0) {
-		debug("Could not find SROMC node\n");
-		return node;
-	}
-
-	config->bank = fdtdec_get_int(blob, node, "bank", 0);
-	config->width = fdtdec_get_int(blob, node, "width", 2);
-
-	err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
-			FDT_SROM_TIMING_COUNT);
-	if (err < 0) {
-		debug("Could not decode SROMC configuration\n");
-		return -FDT_ERR_NOTFOUND;
+	int i;
+	u32 addr, size;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+		gd->bd->bi_dram[i].start = addr;
+		gd->bd->bi_dram[i].size = size;
 	}
-
-	return 0;
 }
-#endif
 
 int board_eth_init(bd_t *bis)
 {
@@ -313,27 +233,6 @@  int board_eth_init(bd_t *bis)
 	struct fdt_sromc config;
 	fdt_addr_t base_addr;
 
-#ifdef CONFIG_OF_CONTROL
-	int node;
-
-	node = decode_sromc(gd->fdt_blob, &config);
-	if (node < 0) {
-		debug("%s: Could not find sromc configuration\n", __func__);
-		return 0;
-	}
-	node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
-	if (node < 0) {
-		debug("%s: Could not find lan9215 configuration\n", __func__);
-		return 0;
-	}
-
-	/* We now have a node, so any problems from now on are errors */
-	base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
-	if (base_addr == FDT_ADDR_T_NONE) {
-		debug("%s: Could not find lan9215 address\n", __func__);
-		return -1;
-	}
-#else
 	/* Non-FDT configuration - bank number and timing parameters*/
 	config.bank = CONFIG_ENV_SROM_BANK;
 	config.width = 2;
@@ -346,7 +245,6 @@  int board_eth_init(bd_t *bis)
 	config.timing[FDT_SROM_TACP] = 0x09;
 	config.timing[FDT_SROM_PMC] = 0x01;
 	base_addr = CONFIG_SMC911X_BASE;
-#endif
 
 	/* Ethernet needs data bus width of 16 bits */
 	if (config.width != 2) {
@@ -376,17 +274,7 @@  int board_eth_init(bd_t *bis)
 #ifdef CONFIG_DISPLAY_BOARDINFO
 int checkboard(void)
 {
-#ifdef CONFIG_OF_CONTROL
-	const char *board_name;
-
-	board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
-	if (board_name == NULL)
-		printf("\nUnknown Board\n");
-	else
-		printf("\nBoard: %s\n", board_name);
-#else
 	printf("\nBoard: SMDK5250\n");
-#endif
 	return 0;
 }
 #endif
@@ -394,48 +282,54 @@  int checkboard(void)
 #ifdef CONFIG_GENERIC_MMC
 int board_mmc_init(bd_t *bis)
 {
-	int err;
+	int err, ret = 0, index, bus_width;
+	u32 base;
 
 	err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
-	if (err) {
+	if (err)
 		debug("SDMMC0 not configured\n");
-		return err;
-	}
-
-	err = s5p_mmc_init(0, 8);
-	return err;
+	ret |= err;
+
+	/*EMMC: dwmmc Channel-0 with 8 bit bus width */
+	index = 0;
+	base =  samsung_get_base_mmc() + (0x10000 * index);
+	bus_width = 8;
+	err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL);
+	if (err)
+		debug("dwmmc Channel-0 init failed\n");
+	ret |= err;
+
+	err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+	if (err)
+		debug("SDMMC2 not configured\n");
+	ret |= err;
+
+	/*SD: dwmmc Channel-2 with 4 bit bus width */
+	index = 2;
+	base = samsung_get_base_mmc() + (0x10000 * index);
+	bus_width = 4;
+	err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL);
+	if (err)
+		debug("dwmmc Channel-2 init failed\n");
+	ret |= err;
+
+	return ret;
 }
 #endif
 
 static int board_uart_init(void)
 {
-	int err;
-
-	err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
-	if (err) {
-		debug("UART0 not configured\n");
-		return err;
+	int err, uart_id, ret = 0;
+
+	for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+		err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+		if (err) {
+			debug("UART%d not configured\n",
+			      (uart_id - PERIPH_ID_UART0));
+			ret |= err;
+		}
 	}
-
-	err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
-	if (err) {
-		debug("UART1 not configured\n");
-		return err;
-	}
-
-	err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
-	if (err) {
-		debug("UART2 not configured\n");
-		return err;
-	}
-
-	err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
-	if (err) {
-		debug("UART3 not configured\n");
-		return err;
-	}
-
-	return 0;
+	return ret;
 }
 
 #ifdef CONFIG_BOARD_EARLY_INIT_F
@@ -448,7 +342,7 @@  int board_early_init_f(void)
 		return err;
 	}
 #ifdef CONFIG_SYS_I2C_INIT_BOARD
-	board_i2c_init(gd->fdt_blob);
+	board_i2c_init(NULL);
 #endif
 	return err;
 }
@@ -477,7 +371,6 @@  void exynos_set_dp_phy(unsigned int onoff)
 	set_dp_phy_ctrl(onoff);
 }
 
-#ifndef CONFIG_OF_CONTROL
 vidinfo_t panel_info = {
 	.vl_freq	= 60,
 	.vl_col		= 2560,
@@ -543,13 +436,9 @@  static struct exynos_dp_platform_data dp_platform_data = {
 	.edp_dev_info	= &edp_info,
 };
 
-#endif
 void init_panel_info(vidinfo_t *vid)
 {
-#ifndef CONFIG_OF_CONTROL
-	vid->rgb_mode   = MODE_RGB_P,
-
+	vid->rgb_mode   = MODE_RGB_P;
 	exynos_set_dp_platform_data(&dp_platform_data);
-#endif
 }
 #endif
diff --git a/drivers/video/exynos_fb.c b/drivers/video/exynos_fb.c
index dfe329f..d3bb7f4 100644
--- a/drivers/video/exynos_fb.c
+++ b/drivers/video/exynos_fb.c
@@ -331,10 +331,10 @@  void lcd_ctrl_init(void *lcdbase)
 #ifdef CONFIG_OF_CONTROL
 	if (exynos_fimd_parse_dt(gd->fdt_blob))
 		debug("Can't get proper panel info\n");
-#endif
+#else
 	/* initialize parameters which is specific to panel. */
 	init_panel_info(&panel_info);
-
+#endif
 	panel_width = panel_info.vl_width;
 	panel_height = panel_info.vl_height;
 
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index 496a194..e026362 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -100,6 +100,10 @@ 
 #define CONFIG_MMC
 #define CONFIG_SDHCI
 #define CONFIG_S5P_SDHCI
+#define CONFIG_DWMMC
+#define CONFIG_EXYNOS_DWMMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+
 
 #define CONFIG_BOARD_EARLY_INIT_F
 
@@ -220,6 +224,10 @@ 
 #define SPI_FLASH_UBOOT_POS		(CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
 
 #define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_PART
+#define CONFIG_PARTITION_UUIDS
+
 
 #define CONFIG_IRAM_STACK	0x02050000