@@ -4095,13 +4095,6 @@
S [KNL] Run init in single mode
- s390_iommu= [HW,S390]
- Set s390 IOTLB flushing mode
- strict
- With strict flushing every unmap operation will result in
- an IOTLB flush. Default is lazy flushing before reuse,
- which is faster.
-
sa1100ir [NET]
See drivers/net/irda/sa1100_ir.c.
@@ -17,7 +17,6 @@
static struct kmem_cache *dma_region_table_cache;
static struct kmem_cache *dma_page_table_cache;
-static int s390_iommu_strict;
static int zpci_refresh_global(struct zpci_dev *zdev)
{
@@ -193,13 +192,13 @@ static int __dma_purge_tlb(struct zpci_dev *zdev, dma_addr_t dma_addr,
if (!zdev->tlb_refresh)
return 0;
} else {
- if (!s390_iommu_strict)
+ if (IOMMU_DMA_MODE_IS_LAZY())
return 0;
}
ret = zpci_refresh_trans((u64) zdev->fh << 32, dma_addr,
PAGE_ALIGN(size));
- if (ret == -ENOMEM && !s390_iommu_strict) {
+ if (ret == -ENOMEM && IOMMU_DMA_MODE_IS_LAZY()) {
/* enable the hypervisor to free some resources */
if (zpci_refresh_global(zdev))
goto out;
@@ -278,7 +277,7 @@ static dma_addr_t dma_alloc_address(struct device *dev, int size)
spin_lock_irqsave(&zdev->iommu_bitmap_lock, flags);
offset = __dma_alloc_iommu(dev, zdev->next_bit, size);
if (offset == -1) {
- if (!s390_iommu_strict) {
+ if (IOMMU_DMA_MODE_IS_LAZY()) {
/* global flush before DMA addresses are reused */
if (zpci_refresh_global(zdev))
goto out_error;
@@ -313,7 +312,7 @@ static void dma_free_address(struct device *dev, dma_addr_t dma_addr, int size)
if (!zdev->iommu_bitmap)
goto out;
- if (s390_iommu_strict)
+ if (!IOMMU_DMA_MODE_IS_LAZY())
bitmap_clear(zdev->iommu_bitmap, offset, size);
else
bitmap_set(zdev->lazy_bitmap, offset, size);
@@ -584,7 +583,7 @@ int zpci_dma_init_device(struct zpci_dev *zdev)
rc = -ENOMEM;
goto free_dma_table;
}
- if (!s390_iommu_strict) {
+ if (IOMMU_DMA_MODE_IS_LAZY()) {
zdev->lazy_bitmap = vzalloc(zdev->iommu_pages / 8);
if (!zdev->lazy_bitmap) {
rc = -ENOMEM;
@@ -671,12 +670,3 @@ void zpci_dma_exit(void)
/* dma_supported is unconditionally true without a callback */
};
EXPORT_SYMBOL_GPL(s390_pci_dma_ops);
-
-static int __init s390_iommu_setup(char *str)
-{
- if (!strncmp(str, "strict", 6))
- s390_iommu_strict = 1;
- return 0;
-}
-
-__setup("s390_iommu=", s390_iommu_setup);
@@ -77,6 +77,7 @@ config IOMMU_DEBUGFS
choice
prompt "IOMMU dma mode"
depends on IOMMU_API
+ default IOMMU_DMA_MODE_LAZY if S390_IOMMU
default IOMMU_DMA_MODE_STRICT
help
IOMMU dma mode, such as: passthrough, lazy, strict.
s390_iommu=strict can be replaced with iommu.dma_mode=strict. Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> --- Documentation/admin-guide/kernel-parameters.txt | 7 ------- arch/s390/pci/pci_dma.c | 20 +++++--------------- drivers/iommu/Kconfig | 1 + 3 files changed, 6 insertions(+), 22 deletions(-) -- 1.8.3