@@ -140,7 +140,7 @@ static void davinci_mdio_init_clk(struct davinci_mdio_data *data)
static void davinci_mdio_enable(struct davinci_mdio_data *data)
{
/* set enable and clock divider */
- __raw_writel(data->clk_div | CONTROL_ENABLE, &data->regs->control);
+ writel(data->clk_div | CONTROL_ENABLE, &data->regs->control);
}
static int davinci_mdio_reset(struct mii_bus *bus)
@@ -159,7 +159,7 @@ static int davinci_mdio_reset(struct mii_bus *bus)
msleep(PHY_MAX_ADDR * data->access_time);
/* dump hardware version info */
- ver = __raw_readl(&data->regs->version);
+ ver = readl(&data->regs->version);
dev_info(data->dev,
"davinci mdio revision %d.%d, bus freq %ld\n",
(ver >> 8) & 0xff, ver & 0xff,
@@ -169,7 +169,7 @@ static int davinci_mdio_reset(struct mii_bus *bus)
goto done;
/* get phy mask from the alive register */
- phy_mask = __raw_readl(&data->regs->alive);
+ phy_mask = readl(&data->regs->alive);
if (phy_mask) {
/* restrict mdio bus to live phys only */
dev_info(data->dev, "detected phy mask %x\n", ~phy_mask);
@@ -196,11 +196,11 @@ static inline int wait_for_user_access(struct davinci_mdio_data *data)
u32 reg;
while (time_after(timeout, jiffies)) {
- reg = __raw_readl(®s->user[0].access);
+ reg = readl(®s->user[0].access);
if ((reg & USERACCESS_GO) == 0)
return 0;
- reg = __raw_readl(®s->control);
+ reg = readl(®s->control);
if ((reg & CONTROL_IDLE) == 0) {
usleep_range(100, 200);
continue;
@@ -216,7 +216,7 @@ static inline int wait_for_user_access(struct davinci_mdio_data *data)
return -EAGAIN;
}
- reg = __raw_readl(®s->user[0].access);
+ reg = readl(®s->user[0].access);
if ((reg & USERACCESS_GO) == 0)
return 0;
@@ -263,7 +263,7 @@ static int davinci_mdio_read(struct mii_bus *bus, int phy_id, int phy_reg)
if (ret < 0)
break;
- __raw_writel(reg, &data->regs->user[0].access);
+ writel(reg, &data->regs->user[0].access);
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
@@ -271,7 +271,7 @@ static int davinci_mdio_read(struct mii_bus *bus, int phy_id, int phy_reg)
if (ret < 0)
break;
- reg = __raw_readl(&data->regs->user[0].access);
+ reg = readl(&data->regs->user[0].access);
ret = (reg & USERACCESS_ACK) ? (reg & USERACCESS_DATA) : -EIO;
break;
}
@@ -307,7 +307,7 @@ static int davinci_mdio_write(struct mii_bus *bus, int phy_id,
if (ret < 0)
break;
- __raw_writel(reg, &data->regs->user[0].access);
+ writel(reg, &data->regs->user[0].access);
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
@@ -472,9 +472,9 @@ static int davinci_mdio_runtime_suspend(struct device *dev)
u32 ctrl;
/* shutdown the scan state machine */
- ctrl = __raw_readl(&data->regs->control);
+ ctrl = readl(&data->regs->control);
ctrl &= ~CONTROL_ENABLE;
- __raw_writel(ctrl, &data->regs->control);
+ writel(ctrl, &data->regs->control);
wait_for_idle(data);
return 0;
Switch to readl/writel() APIs, because this is recommended API and the MDIO block is reused on Keystone 2 SoCs where LE/BE modes are supported. Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> --- changes in v2: - use readl/writel() as recommended drivers/net/ethernet/ti/davinci_mdio.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) -- 2.17.1