@@ -1024,6 +1024,109 @@
};
};
+ pcie0: pci@1c00000 {
+ compatible = "qcom,pcie-sdm845", "snps,dw-pcie";
+ reg = <0 0x01c00000 0 0x2000>,
+ <0 0x60000000 0 0xf1d>,
+ <0 0x60000f20 0 0xa8>,
+ <0 0x60100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+ <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0xd00000>;
+
+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+ clock-names = "pipe",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "tbu";
+
+ iommu-map = <0x0 &apps_smmu 0x1c10 0x1>,
+ <0x100 &apps_smmu 0x1c11 0x1>,
+ <0x200 &apps_smmu 0x1c12 0x1>,
+ <0x300 &apps_smmu 0x1c13 0x1>,
+ <0x400 &apps_smmu 0x1c14 0x1>,
+ <0x500 &apps_smmu 0x1c15 0x1>,
+ <0x600 &apps_smmu 0x1c16 0x1>,
+ <0x700 &apps_smmu 0x1c17 0x1>,
+ <0x800 &apps_smmu 0x1c18 0x1>,
+ <0x900 &apps_smmu 0x1c19 0x1>,
+ <0xa00 &apps_smmu 0x1c1a 0x1>,
+ <0xb00 &apps_smmu 0x1c1b 0x1>,
+ <0xc00 &apps_smmu 0x1c1c 0x1>,
+ <0xd00 &apps_smmu 0x1c1d 0x1>,
+ <0xe00 &apps_smmu 0x1c1e 0x1>,
+ <0xf00 &apps_smmu 0x1c1f 0x1>;
+
+ resets = <&gcc GCC_PCIE_0_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_0_GDSC>;
+
+ phys = <&pcie0_lane>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie0_phy: phy@1c06000 {
+ compatible = "qcom,sdm845-qmp-pcie-phy";
+ reg = <0 0x01c06000 0 0x18c>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_CLKREF_CLK>,
+ <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie0_lane: lanes@1c06200 {
+ reg = <0 0x01c06200 0 0x128>,
+ <0 0x01c06400 0 0x1fc>,
+ <0 0x01c06800 0 0x218>,
+ <0 0x01c06600 0 0x70>;
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ clock-output-names = "pcie_0_pipe_clk";
+ };
+ };
+
ufs_mem_hc: ufshc@1d84000 {
compatible = "qcom,sdm845-ufshc", "qcom,ufshc",
"jedec,ufs-2.0";
SDM845 sports two PCIe controller/phy pairs; one GEN2 and one GEN3. Add the nodes for the GEN2 pair. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> --- Changes since v1: - "reg" is spelled without a 't' arch/arm64/boot/dts/qcom/sdm845.dtsi | 103 +++++++++++++++++++++++++++ 1 file changed, 103 insertions(+) -- 2.18.0