diff mbox

mmc: core: Re-use code for MMC_CAP2_DETECT_ON_ERR in polling mode

Message ID 1364400700-13161-1-git-send-email-ulf.hansson@stericsson.com
State Superseded
Headers show

Commit Message

Ulf Hansson March 27, 2013, 4:11 p.m. UTC 
From: Ulf Hansson <ulf.hansson@linaro.org>

Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.

Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
 drivers/mmc/core/core.c  |    5 ++---
 include/linux/mmc/host.h |    1 -
 2 files changed, 2 insertions(+), 4 deletions(-)
diff mbox

Patch

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index ad7decc..59ae194 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -2325,14 +2325,13 @@  int mmc_detect_card_removed(struct mmc_host *host)
 	 * The card will be considered unchanged unless we have been asked to
 	 * detect a change or host requires polling to provide card detection.
 	 */
-	if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL) &&
-	    !(host->caps2 & MMC_CAP2_DETECT_ON_ERR))
+	if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL))
 		return ret;
 
 	host->detect_change = 0;
 	if (!ret) {
 		ret = _mmc_detect_card_removed(host);
-		if (ret && (host->caps2 & MMC_CAP2_DETECT_ON_ERR)) {
+		if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) {
 			/*
 			 * Schedule a detect work as soon as possible to let a
 			 * rescan handle the card removal.
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 17d7148..301892a 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -272,7 +272,6 @@  struct mmc_host {
 #define MMC_CAP2_HS200		(MMC_CAP2_HS200_1_8V_SDR | \
 				 MMC_CAP2_HS200_1_2V_SDR)
 #define MMC_CAP2_BROKEN_VOLTAGE	(1 << 7)	/* Use the broken voltage */
-#define MMC_CAP2_DETECT_ON_ERR	(1 << 8)	/* On I/O err check card removal */
 #define MMC_CAP2_HC_ERASE_SZ	(1 << 9)	/* High-capacity erase size */
 #define MMC_CAP2_CD_ACTIVE_HIGH	(1 << 10)	/* Card-detect signal active high */
 #define MMC_CAP2_RO_ACTIVE_HIGH	(1 << 11)	/* Write-protect signal active high */