diff mbox series

[v4,1/2] dt-bindings: media: Binding document for OV7251 camera sensor

Message ID 1524673246-14175-2-git-send-email-todor.tomov@linaro.org
State Accepted
Commit eae419efec329921ea5f3e6ae5b44c4aa33437f0
Headers show
Series [v4,1/2] dt-bindings: media: Binding document for OV7251 camera sensor | expand

Commit Message

Todor Tomov April 25, 2018, 4:20 p.m. UTC
Add the document for ov7251 device tree binding.

CC: Rob Herring <robh@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>

Reviewed-by: Rob Herring <robh@kernel.org>

---
 .../devicetree/bindings/media/i2c/ov7251.txt       | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov7251.txt

-- 
2.7.4
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
new file mode 100644
index 0000000..8281151
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
@@ -0,0 +1,52 @@ 
+* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor
+
+The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor
+with an active array size of 640H x 480V. It is programmable through a serial
+I2C interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov7251".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin XSHUTDOWN which is physically active low.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node shall contain one 'port' child node with a single 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov7251: camera-sensor@60 {
+			compatible = "ovti,ov7251";
+			reg = <0x60>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_bw_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <24000000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov7251_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};