@@ -743,6 +743,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
qcom-apq8064-asus-nexus7-flo.dtb \
+ qcom-apq8064-db600c.dtb \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
new file mode 100644
@@ -0,0 +1,530 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+
+/ {
+ model = "Qualcomm Technologies, Inc. DB600c";
+ compatible = "arrow,apq8064-db600c", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi1_serial;
+ i2c0 = &gsbi2_i2c;
+ i2c1 = &gsbi3_i2c;
+ i2c2 = &gsbi4_i2c;
+ i2c3 = &gsbi7_i2c;
+ spi0 = &gsbi5_spi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ vph: regulator-fixed {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <4500000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ };
+
+ /* on board fixed 3.3v supply */
+ vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+ };
+
+ soc {
+ pinctrl@800000 {
+ card_detect: card_detect {
+ mux {
+ pins = "gpio26";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ user_leds: user-leds {
+ mux {
+ pins = "gpio6", "gpio7", "gpio35", "gpio86";
+ function = "gpio";
+ };
+
+ conf {
+ pins = "gpio6", "gpio7", "gpio35", "gpio86";
+ function = "gpio";
+ output-low;
+ };
+ };
+
+ i2c1 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c2 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c3 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c4 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c5 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c6 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c7 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ i2c1 {
+ pinconf {
+ drive-strength = <8>;
+ };
+ };
+
+ spi5_default {
+ pinconf {
+ drive-strength = <8>;
+ };
+
+ pinconf_cs {
+ drive-strength = <8>;
+ };
+ };
+ };
+
+ qcom,ssbi@500000 {
+ pmic@0 {
+ mpps@50 {
+ pcie_perst: pcie-perst {
+ pinconf {
+ pins = "mpp1";
+ function = "digital";
+ power-source = <PM8921_MPP_S4>;
+ output-low;
+ };
+ };
+
+ mpp_leds: mpp-leds {
+ pinconf {
+ pins = "mpp7", "mpp8", "mpp9", "mpp10", "mpp11", "mpp12";
+ function = "digital";
+ power-source = <PM8921_MPP_VPH>;
+ drive-strength = <12>;
+ output-high;
+ };
+ };
+ };
+ };
+ };
+
+ rpm@108000 {
+ regulators {
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_s5-supply = <&vph>;
+ vdd_s6-supply = <&vph>;
+ vdd_s7-supply = <&vph>;
+
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l3_l15_l17-supply = <&vph>;
+ vdd_l4_l14-supply = <&vph>;
+ vdd_l5_l8_l16-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l9_l11-supply = <&vph>;
+ vdd_l10_l22-supply = <&vph>;
+ vdd_l21_l23_l29-supply = <&vph>;
+
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ l7 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /**
+ * 1.8v required on LS expansion
+ * for mezzanine boards
+ */
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ l26 {
+ regulator-min-microvolt = < 375000>;
+ regulator-max-microvolt = <1050000>;
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial@12450000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi1_uart_4pins>;
+ };
+ };
+
+ gsbi@12480000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@124a0000 {
+ /* On Low speed expansion and Sensors */
+ label = "LS-I2C0";
+ status = "okay";
+ };
+ };
+
+ gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16280000 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+ clock-frequency = <200000>;
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <64>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16380000 {
+ /* On High speed expansion */
+ label = "HS-CAM-I2C3";
+ status = "okay";
+ };
+ };
+
+ gsbi@1a200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_SPI>;
+ spi@1a280000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+ };
+
+ gsbi@16500000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial@1654000 {
+ label = "BT-UART";
+ status = "okay";
+ pinctrl-name = "default";
+ pinctrl-0 = <&gsbi6_uart_4pins>;
+ };
+ };
+
+
+ /* DEBUG UART */
+ gsbi@16600000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16640000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+
+ };
+
+ i2c@16680000 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-CAM-I2C2";
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+ compatible = "gpio-leds";
+
+ user-led0 {
+ label = "user0-led";
+ gpios = <&pm8921_mpps 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ user-led1 {
+ label = "user1-led";
+ gpios = <&pm8921_mpps 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ user-led2 {
+ label = "user2-led";
+ gpios = <&pm8921_mpps 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led3 {
+ label = "user3-led";
+ gpios = <&pm8921_mpps 12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ };
+
+ wifi-led {
+ label = "WiFi-led";
+ gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "none";
+ };
+
+ bt-led {
+ label = "BT-led";
+ gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "none";
+ };
+ };
+
+ pci@1b500000 {
+ status = "okay";
+ vdda-supply = <&pm8921_s3>;
+ vdda_phy-supply = <&pm8921_lvs6>;
+ vdda_refclk-supply = <&vcc3v3>;
+ pinctrl-0 = <&pcie_perst>;
+ pinctrl-names = "default";
+ perst-gpio = <&pm8921_mpps 1 GPIO_ACTIVE_LOW>;
+ };
+
+ /* OTG */
+ usb@12500000 {
+ status = "okay";
+ dr_mode = "otg";
+ ulpi {
+ phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+ };
+ };
+
+ usb@12520000 {
+ status = "okay";
+ dr_mode = "host";
+ ulpi {
+ phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+ };
+ };
+
+ usb@12530000 {
+ status = "okay";
+ dr_mode = "host";
+ ulpi {
+ phy {
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+ };
+ };
+
+ amba {
+ /* eMMC */
+ sdcc1: sdcc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+
+ /* External micro SD card */
+ sdcc3: sdcc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ vqmmc-supply = <&pm8921_l7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdcc3_pins &card_detect>;
+ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ hdmi-tx@4a00000 {
+ status = "okay";
+ core-vdda-supply = <&pm8921_hdmi_switch>;
+ hdmi-mux-supply = <&vcc3v3>;
+
+ hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ hdmi-phy@4a00400 {
+ status = "okay";
+ core-vdda-supply = <&pm8921_hdmi_switch>;
+ };
+
+ mdp@5100000 {
+ status = "okay";
+
+ ports {
+ port@3 {
+ endpoint {
+ remote-endpoint = <&hdmi_in>;
+ };
+ };
+ };
+ };
+ };
+};