@@ -337,36 +337,6 @@ static void get_samsung_nand_para(struct denali_nand_info *denali,
}
}
-static void get_toshiba_nand_para(struct denali_nand_info *denali)
-{
- /*
- * Workaround to fix a controller bug which reports a wrong
- * spare area size for some kind of Toshiba NAND device
- */
- if ((ioread32(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) &&
- (ioread32(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64))
- iowrite32(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
-}
-
-static void get_hynix_nand_para(struct denali_nand_info *denali,
- uint8_t device_id)
-{
- switch (device_id) {
- case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */
- case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */
- iowrite32(128, denali->flash_reg + PAGES_PER_BLOCK);
- iowrite32(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
- iowrite32(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
- iowrite32(0, denali->flash_reg + DEVICE_WIDTH);
- break;
- default:
- dev_warn(denali->dev,
- "Unknown Hynix NAND (Device ID: 0x%x).\n"
- "Will use default parameter values instead.\n",
- device_id);
- }
-}
-
/*
* determines how many NAND chips are connected to the controller. Note for
* Intel CE4100 devices we don't support more than one device.
@@ -453,10 +423,6 @@ static uint16_t denali_nand_timing_set(struct denali_nand_info *denali)
return FAIL;
} else if (maf_id == 0xEC) { /* Samsung NAND */
get_samsung_nand_para(denali, device_id);
- } else if (maf_id == 0x98) { /* Toshiba NAND */
- get_toshiba_nand_para(denali);
- } else if (maf_id == 0xAD) { /* Hynix NAND */
- get_hynix_nand_para(denali, device_id);
}
dev_info(denali->dev,
@@ -1622,6 +1588,12 @@ int denali_init(struct denali_nand_info *denali)
chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
iowrite32(chip->ecc.strength, denali->flash_reg + ECC_CORRECTION);
+ iowrite32(mtd->erasesize / mtd->writesize,
+ denali->flash_reg + PAGES_PER_BLOCK);
+ iowrite32(chip->options & NAND_BUSWIDTH_16 ? 1 : 0,
+ denali->flash_reg + DEVICE_WIDTH);
+ iowrite32(mtd->writesize, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
+ iowrite32(mtd->oobsize, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
iowrite32(chip->ecc.size, denali->flash_reg + CFG_DATA_BLOCK_SIZE);
iowrite32(chip->ecc.size, denali->flash_reg + CFG_LAST_DATA_BLOCK_SIZE);
The Denali IP can automatically detect device parameters such as page size, oob size, device width, etc. and this driver currently relies on it. However, this hardware function is known to be problematic. [1] Due to a hardware bug, various misdetected cases were reported. That is why get_toshiba_nand_para() and get_hynix_nand_para() exist to fix-up the misdetected parameters. It is not realistic to add a new NAND device to the *black list* every time we are hit by a misdetected case. We would never be able to guarantee that all cases are covered. [2] Because this feature is unreliable, it is disabled on some platforms. The nand_scan_ident() detects device parameters in a more tested way. The hardware should not set the device parameter registers in a different, unreliable way. Instead, set the parameters from the nand_scan_ident() back to the registers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> --- Changes in v5: None Changes in v4: None Changes in v3: None Changes in v2: None drivers/mtd/nand/denali.c | 40 ++++++---------------------------------- 1 file changed, 6 insertions(+), 34 deletions(-) -- 2.7.4