@@ -21,3 +21,13 @@ config PCI_PWRCTL_SLOT
This is a generic driver that controls the power state of different
PCI slots. The voltage regulators powering the rails of the PCI slots
are expected to be defined in the devicetree node of the PCI bridge.
+
+config PCI_PWRCTRL_TC9563
+ tristate "PCI Power Control driver for TC9563 PCIe switch"
+ select PCI_PWRCTL
+ help
+ Say Y here to enable the PCI Power Control driver of TC9563 PCIe
+ switch.
+
+ This driver enables power and configures the TC9563 PCIe switch
+ through i2c.
@@ -7,3 +7,5 @@ obj-$(CONFIG_PCI_PWRCTL_PWRSEQ) += pci-pwrctrl-pwrseq.o
obj-$(CONFIG_PCI_PWRCTL_SLOT) += pci-pwrctl-slot.o
pci-pwrctl-slot-y := slot.o
+
+obj-$(CONFIG_PCI_PWRCTRL_TC9563) += pci-pwrctrl-tc9563.o
new file mode 100644
@@ -0,0 +1,628 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/pci-pwrctrl.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/unaligned.h>
+
+#include "../pci.h"
+
+#define TC9563_GPIO_CONFIG 0x801208
+#define TC9563_RESET_GPIO 0x801210
+
+#define TC9563_BUS_CONTROL 0x801014
+
+#define TC9563_PORT_L0S_DELAY 0x82496c
+#define TC9563_PORT_L1_DELAY 0x824970
+
+#define TC9563_EMBEDDED_ETH_DELAY 0x8200d8
+#define TC9563_ETH_L1_DELAY_MASK GENMASK(27, 18)
+#define TC9563_ETH_L1_DELAY_VALUE(x) FIELD_PREP(TC9563_ETH_L1_DELAY_MASK, x)
+#define TC9563_ETH_L0S_DELAY_MASK GENMASK(17, 13)
+#define TC9563_ETH_L0S_DELAY_VALUE(x) FIELD_PREP(TC9563_ETH_L0S_DELAY_MASK, x)
+
+#define TC9563_NFTS_2_5_GT 0x824978
+#define TC9563_NFTS_5_GT 0x82497c
+
+#define TC9563_PORT_LANE_ACCESS_ENABLE 0x828000
+
+#define TC9563_PHY_RATE_CHANGE_OVERRIDE 0x828040
+#define TC9563_PHY_RATE_CHANGE 0x828050
+
+#define TC9563_TX_MARGIN 0x828234
+
+#define TC9563_DFE_ENABLE 0x828a04
+#define TC9563_DFE_EQ0_MODE 0x828a08
+#define TC9563_DFE_EQ1_MODE 0x828a0c
+#define TC9563_DFE_EQ2_MODE 0x828a14
+#define TC9563_DFE_PD_MASK 0x828254
+
+#define TC9563_PORT_SELECT 0x82c02c
+#define TC9563_PORT_ACCESS_ENABLE 0x82c030
+
+#define TC9563_POWER_CONTROL 0x82b09c
+#define TC9563_POWER_CONTROL_OVREN 0x82b2c8
+
+#define TC9563_GPIO_MASK 0xfffffff3
+
+#define TC9563_TX_MARGIN_MIN_VAL 400000
+
+struct tc9563_pwrctrl_reg_setting {
+ unsigned int offset;
+ unsigned int val;
+};
+
+enum tc9563_pwrctrl_ports {
+ TC9563_USP,
+ TC9563_DSP1,
+ TC9563_DSP2,
+ TC9563_DSP3,
+ TC9563_ETHERNET,
+ TC9563_MAX
+};
+
+struct tc9563_pwrctrl_cfg {
+ u32 l0s_delay;
+ u32 l1_delay;
+ u32 tx_amp;
+ u8 nfts[2]; /* GEN1 & GEN2 */
+ bool disable_dfe;
+ bool disable_port;
+};
+
+#define TC9563_PWRCTL_MAX_SUPPLY 6
+
+struct tc9563_pwrctrl_ctx {
+ struct regulator_bulk_data supplies[TC9563_PWRCTL_MAX_SUPPLY];
+ struct tc9563_pwrctrl_cfg cfg[TC9563_MAX];
+ struct gpio_desc *reset_gpio;
+ struct i2c_adapter *adapter;
+ struct i2c_client *client;
+ struct pci_pwrctrl pwrctrl;
+};
+
+/*
+ * downstream port power off sequence, hardcoding the address
+ * as we don't know register names for these register offsets.
+ */
+static const struct tc9563_pwrctrl_reg_setting common_pwroff_seq[] = {
+ {0x82900c, 0x1},
+ {0x829010, 0x1},
+ {0x829018, 0x0},
+ {0x829020, 0x1},
+ {0x82902c, 0x1},
+ {0x829030, 0x1},
+ {0x82903c, 0x1},
+ {0x829058, 0x0},
+ {0x82905c, 0x1},
+ {0x829060, 0x1},
+ {0x8290cc, 0x1},
+ {0x8290d0, 0x1},
+ {0x8290d8, 0x1},
+ {0x8290e0, 0x1},
+ {0x8290e8, 0x1},
+ {0x8290ec, 0x1},
+ {0x8290f4, 0x1},
+ {0x82910c, 0x1},
+ {0x829110, 0x1},
+ {0x829114, 0x1},
+};
+
+static const struct tc9563_pwrctrl_reg_setting dsp1_pwroff_seq[] = {
+ {TC9563_PORT_ACCESS_ENABLE, 0x2},
+ {TC9563_PORT_LANE_ACCESS_ENABLE, 0x3},
+ {TC9563_POWER_CONTROL, 0x014f4804},
+ {TC9563_POWER_CONTROL_OVREN, 0x1},
+ {TC9563_PORT_ACCESS_ENABLE, 0x4},
+};
+
+static const struct tc9563_pwrctrl_reg_setting dsp2_pwroff_seq[] = {
+ {TC9563_PORT_ACCESS_ENABLE, 0x8},
+ {TC9563_PORT_LANE_ACCESS_ENABLE, 0x1},
+ {TC9563_POWER_CONTROL, 0x014f4804},
+ {TC9563_POWER_CONTROL_OVREN, 0x1},
+ {TC9563_PORT_ACCESS_ENABLE, 0x8},
+};
+
+/*
+ * Since all transfers are initiated by the probe, no locks are necessary,
+ * as there are no concurrent calls.
+ */
+static int tc9563_pwrctrl_i2c_write(struct i2c_client *client,
+ u32 reg_addr, u32 reg_val)
+{
+ struct i2c_msg msg;
+ u8 msg_buf[7];
+ int ret;
+
+ msg.addr = client->addr;
+ msg.len = 7;
+ msg.flags = 0;
+
+ /* Big Endian for reg addr */
+ put_unaligned_be24(reg_addr, &msg_buf[0]);
+
+ /* Little Endian for reg val */
+ put_unaligned_le32(reg_val, &msg_buf[3]);
+
+ msg.buf = msg_buf;
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ return ret == 1 ? 0 : ret;
+}
+
+static int tc9563_pwrctrl_i2c_read(struct i2c_client *client,
+ u32 reg_addr, u32 *reg_val)
+{
+ struct i2c_msg msg[2];
+ u8 wr_data[3];
+ u32 rd_data;
+ int ret;
+
+ msg[0].addr = client->addr;
+ msg[0].len = 3;
+ msg[0].flags = 0;
+
+ /* Big Endian for reg addr */
+ put_unaligned_be24(reg_addr, &wr_data[0]);
+
+ msg[0].buf = wr_data;
+
+ msg[1].addr = client->addr;
+ msg[1].len = 4;
+ msg[1].flags = I2C_M_RD;
+
+ msg[1].buf = (u8 *)&rd_data;
+
+ ret = i2c_transfer(client->adapter, &msg[0], 2);
+ if (ret == 2) {
+ *reg_val = get_unaligned_le32(&rd_data);
+ return 0;
+ }
+
+ /* If only one message successfully completed, return -EIO */
+ return ret == 1 ? -EIO : ret;
+}
+
+static int tc9563_pwrctrl_i2c_bulk_write(struct i2c_client *client,
+ const struct tc9563_pwrctrl_reg_setting *seq, int len)
+{
+ int ret, i;
+
+ for (i = 0; i < len; i++) {
+ ret = tc9563_pwrctrl_i2c_write(client, seq[i].offset, seq[i].val);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int tc9563_pwrctrl_disable_port(struct tc9563_pwrctrl_ctx *ctx,
+ enum tc9563_pwrctrl_ports port)
+{
+ struct tc9563_pwrctrl_cfg *cfg = &ctx->cfg[port];
+ const struct tc9563_pwrctrl_reg_setting *seq;
+ int ret, len;
+
+ if (!cfg->disable_port)
+ return 0;
+
+ if (port == TC9563_DSP1) {
+ seq = dsp1_pwroff_seq;
+ len = ARRAY_SIZE(dsp1_pwroff_seq);
+ } else {
+ seq = dsp2_pwroff_seq;
+ len = ARRAY_SIZE(dsp2_pwroff_seq);
+ }
+
+ ret = tc9563_pwrctrl_i2c_bulk_write(ctx->client, seq, len);
+ if (ret)
+ return ret;
+
+ return tc9563_pwrctrl_i2c_bulk_write(ctx->client,
+ common_pwroff_seq, ARRAY_SIZE(common_pwroff_seq));
+}
+
+static int tc9563_pwrctrl_set_l0s_l1_entry_delay(struct tc9563_pwrctrl_ctx *ctx,
+ enum tc9563_pwrctrl_ports port, bool is_l1, u32 ns)
+{
+ u32 rd_val, units;
+ int ret;
+
+ if (ns < 256)
+ return 0;
+
+ /* convert to units of 256ns */
+ units = ns / 256;
+
+ if (port == TC9563_ETHERNET) {
+ ret = tc9563_pwrctrl_i2c_read(ctx->client, TC9563_EMBEDDED_ETH_DELAY, &rd_val);
+ if (ret)
+ return ret;
+
+ if (is_l1)
+ rd_val = u32_replace_bits(rd_val, units, TC9563_ETH_L1_DELAY_MASK);
+ else
+ rd_val = u32_replace_bits(rd_val, units, TC9563_ETH_L0S_DELAY_MASK);
+
+ return tc9563_pwrctrl_i2c_write(ctx->client, TC9563_EMBEDDED_ETH_DELAY, rd_val);
+ }
+
+ ret = tc9563_pwrctrl_i2c_write(ctx->client, TC9563_PORT_SELECT, BIT(port));
+ if (ret)
+ return ret;
+
+ return tc9563_pwrctrl_i2c_write(ctx->client,
+ is_l1 ? TC9563_PORT_L1_DELAY : TC9563_PORT_L0S_DELAY, units);
+}
+
+static int tc9563_pwrctrl_set_tx_amplitude(struct tc9563_pwrctrl_ctx *ctx,
+ enum tc9563_pwrctrl_ports port, u32 amp)
+{
+ int port_access;
+
+ if (amp < TC9563_TX_MARGIN_MIN_VAL)
+ return 0;
+
+ /* txmargin = (Amp(uV) - 400000) / 3125 */
+ amp = (amp - TC9563_TX_MARGIN_MIN_VAL) / 3125;
+
+ switch (port) {
+ case TC9563_USP:
+ port_access = 0x1;
+ break;
+ case TC9563_DSP1:
+ port_access = 0x2;
+ break;
+ case TC9563_DSP2:
+ port_access = 0x8;
+ break;
+ default:
+ return -EINVAL;
+ };
+
+ struct tc9563_pwrctrl_reg_setting tx_amp_seq[] = {
+ {TC9563_PORT_ACCESS_ENABLE, port_access},
+ {TC9563_PORT_LANE_ACCESS_ENABLE, 0x3},
+ {TC9563_TX_MARGIN, amp},
+ };
+
+ return tc9563_pwrctrl_i2c_bulk_write(ctx->client, tx_amp_seq, ARRAY_SIZE(tx_amp_seq));
+}
+
+static int tc9563_pwrctrl_disable_dfe(struct tc9563_pwrctrl_ctx *ctx,
+ enum tc9563_pwrctrl_ports port)
+{
+ struct tc9563_pwrctrl_cfg *cfg = &ctx->cfg[port];
+ int port_access, lane_access = 0x3;
+ u32 phy_rate = 0x21;
+
+ if (!cfg->disable_dfe)
+ return 0;
+
+ switch (port) {
+ case TC9563_USP:
+ phy_rate = 0x1;
+ port_access = 0x1;
+ break;
+ case TC9563_DSP1:
+ port_access = 0x2;
+ break;
+ case TC9563_DSP2:
+ port_access = 0x8;
+ lane_access = 0x1;
+ break;
+ default:
+ return -EINVAL;
+ };
+
+ struct tc9563_pwrctrl_reg_setting disable_dfe_seq[] = {
+ {TC9563_PORT_ACCESS_ENABLE, port_access},
+ {TC9563_PORT_LANE_ACCESS_ENABLE, lane_access},
+ {TC9563_DFE_ENABLE, 0x0},
+ {TC9563_DFE_EQ0_MODE, 0x411},
+ {TC9563_DFE_EQ1_MODE, 0x11},
+ {TC9563_DFE_EQ2_MODE, 0x11},
+ {TC9563_DFE_PD_MASK, 0x7},
+ {TC9563_PHY_RATE_CHANGE_OVERRIDE, 0x10},
+ {TC9563_PHY_RATE_CHANGE, phy_rate},
+ {TC9563_PHY_RATE_CHANGE, 0x0},
+ {TC9563_PHY_RATE_CHANGE_OVERRIDE, 0x0},
+ };
+
+ return tc9563_pwrctrl_i2c_bulk_write(ctx->client,
+ disable_dfe_seq, ARRAY_SIZE(disable_dfe_seq));
+}
+
+static int tc9563_pwrctrl_set_nfts(struct tc9563_pwrctrl_ctx *ctx,
+ enum tc9563_pwrctrl_ports port, u8 *nfts)
+{
+ struct tc9563_pwrctrl_reg_setting nfts_seq[] = {
+ {TC9563_NFTS_2_5_GT, nfts[0]},
+ {TC9563_NFTS_5_GT, nfts[1]},
+ };
+ int ret;
+
+ if (!nfts[0])
+ return 0;
+
+ ret = tc9563_pwrctrl_i2c_write(ctx->client, TC9563_PORT_SELECT, BIT(port));
+ if (ret)
+ return ret;
+
+ return tc9563_pwrctrl_i2c_bulk_write(ctx->client, nfts_seq, ARRAY_SIZE(nfts_seq));
+}
+
+static int tc9563_pwrctrl_assert_deassert_reset(struct tc9563_pwrctrl_ctx *ctx, bool deassert)
+{
+ int ret, val;
+
+ ret = tc9563_pwrctrl_i2c_write(ctx->client, TC9563_GPIO_CONFIG, TC9563_GPIO_MASK);
+ if (ret)
+ return ret;
+
+ val = deassert ? 0xc : 0;
+
+ return tc9563_pwrctrl_i2c_write(ctx->client, TC9563_RESET_GPIO, val);
+}
+
+static int tc9563_pwrctrl_parse_device_dt(struct tc9563_pwrctrl_ctx *ctx, struct device_node *node,
+ enum tc9563_pwrctrl_ports port)
+{
+ struct tc9563_pwrctrl_cfg *cfg;
+ int ret;
+
+ cfg = &ctx->cfg[port];
+
+ /* Disable port if the status of the port is disabled. */
+ if (!of_device_is_available(node)) {
+ cfg->disable_port = true;
+ return 0;
+ };
+
+ ret = of_property_read_u32(node, "aspm-l0s-entry-delay-ns", &cfg->l0s_delay);
+ if (ret && ret != -EINVAL)
+ return ret;
+
+ ret = of_property_read_u32(node, "aspm-l1-entry-delay-ns", &cfg->l1_delay);
+ if (ret && ret != -EINVAL)
+ return ret;
+
+ ret = of_property_read_u32(node, "qcom,tx-amplitude-microvolt", &cfg->tx_amp);
+ if (ret && ret != -EINVAL)
+ return ret;
+
+ ret = of_property_read_u8_array(node, "nfts", cfg->nfts, 2);
+ if (ret && ret != -EINVAL)
+ return ret;
+
+ cfg->disable_dfe = of_property_read_bool(node, "qcom,no-dfe-support");
+
+ return 0;
+}
+
+static void tc9563_pwrctrl_power_off(struct tc9563_pwrctrl_ctx *ctx)
+{
+ gpiod_set_value(ctx->reset_gpio, 1);
+
+ regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+}
+
+static int tc9563_pwrctrl_bring_up(struct tc9563_pwrctrl_ctx *ctx)
+{
+ struct tc9563_pwrctrl_cfg *cfg;
+ int ret, i;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret < 0)
+ return dev_err_probe(ctx->pwrctrl.dev, ret, "cannot enable regulators\n");
+
+ gpiod_set_value(ctx->reset_gpio, 0);
+
+ /* wait for the internal osc frequency to stablise */
+ usleep_range(10000, 10500);
+
+ ret = tc9563_pwrctrl_assert_deassert_reset(ctx, false);
+ if (ret)
+ goto power_off;
+
+ for (i = 0; i < TC9563_MAX; i++) {
+ cfg = &ctx->cfg[i];
+ ret = tc9563_pwrctrl_disable_port(ctx, i);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Disabling port failed\n");
+ goto power_off;
+ }
+
+ ret = tc9563_pwrctrl_set_l0s_l1_entry_delay(ctx, i, false, cfg->l0s_delay);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Setting L0s entry delay failed\n");
+ goto power_off;
+ }
+
+ ret = tc9563_pwrctrl_set_l0s_l1_entry_delay(ctx, i, true, cfg->l1_delay);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Setting L1 entry delay failed\n");
+ goto power_off;
+ }
+
+ ret = tc9563_pwrctrl_set_tx_amplitude(ctx, i, cfg->tx_amp);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Setting Tx amplitube failed\n");
+ goto power_off;
+ }
+
+ ret = tc9563_pwrctrl_set_nfts(ctx, i, cfg->nfts);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Setting nfts failed\n");
+ goto power_off;
+ }
+
+ ret = tc9563_pwrctrl_disable_dfe(ctx, i);
+ if (ret) {
+ dev_err(ctx->pwrctrl.dev, "Disabling DFE failed\n");
+ goto power_off;
+ }
+ }
+
+ ret = tc9563_pwrctrl_assert_deassert_reset(ctx, true);
+ if (!ret)
+ return 0;
+
+power_off:
+ tc9563_pwrctrl_power_off(ctx);
+ return ret;
+}
+
+static int tc9563_pwrctrl_probe(struct platform_device *pdev)
+{
+ struct pci_host_bridge *bridge = to_pci_host_bridge(pdev->dev.parent);
+ struct pci_dev *pci_dev = to_pci_dev(pdev->dev.parent);
+ struct pci_bus *bus = bridge->bus;
+ struct device *dev = &pdev->dev;
+ enum tc9563_pwrctrl_ports port;
+ struct tc9563_pwrctrl_ctx *ctx;
+ struct device_node *i2c_node;
+ int ret, addr;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ret = of_property_read_u32_index(pdev->dev.of_node, "i2c-parent", 1, &addr);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to read i2c-parent property\n");
+
+ i2c_node = of_parse_phandle(dev->of_node, "i2c-parent", 0);
+ ctx->adapter = of_find_i2c_adapter_by_node(i2c_node);
+ of_node_put(i2c_node);
+ if (!ctx->adapter)
+ return dev_err_probe(dev, -EPROBE_DEFER, "Failed to find I2C adapter\n");
+
+ ctx->client = i2c_new_dummy_device(ctx->adapter, addr);
+ if (IS_ERR(ctx->client)) {
+ dev_err(dev, "Failed to create I2C client\n");
+ i2c_put_adapter(ctx->adapter);
+ return PTR_ERR(ctx->client);
+ }
+
+ ctx->supplies[0].supply = "vddc";
+ ctx->supplies[1].supply = "vdd18";
+ ctx->supplies[2].supply = "vdd09";
+ ctx->supplies[3].supply = "vddio1";
+ ctx->supplies[4].supply = "vddio2";
+ ctx->supplies[5].supply = "vddio18";
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret) {
+ dev_err_probe(dev, ret,
+ "failed to get supply regulator\n");
+ goto remove_i2c;
+ }
+
+ ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->reset_gpio)) {
+ ret = dev_err_probe(dev, PTR_ERR(ctx->reset_gpio), "failed to get reset GPIO\n");
+ goto remove_i2c;
+ }
+
+ pci_pwrctrl_init(&ctx->pwrctrl, dev);
+
+ port = TC9563_USP;
+ ret = tc9563_pwrctrl_parse_device_dt(ctx, pdev->dev.of_node, port);
+ if (ret) {
+ dev_err(dev, "failed to parse device tree properties: %d\n", ret);
+ goto remove_i2c;
+ }
+
+ /*
+ * Downstream ports are always children of the upstream port.
+ * The first node represents DSP1, the second node represents DSP2, and so on.
+ */
+ for_each_child_of_node_scoped(pdev->dev.of_node, child) {
+ ret = tc9563_pwrctrl_parse_device_dt(ctx, child, port++);
+ if (ret)
+ break;
+ /* Embedded ethernet device are under DSP3 */
+ if (port == TC9563_DSP3)
+ for_each_child_of_node_scoped(child, child1) {
+ ret = tc9563_pwrctrl_parse_device_dt(ctx, child1, port++);
+ if (ret)
+ break;
+ }
+ }
+ if (ret) {
+ dev_err(dev, "failed to parse device tree properties: %d\n", ret);
+ goto remove_i2c;
+ }
+
+ if (!pcie_link_is_active(pci_dev) && bridge->ops->stop_link)
+ bridge->ops->stop_link(bus);
+
+ ret = tc9563_pwrctrl_bring_up(ctx);
+ if (ret)
+ goto remove_i2c;
+
+ if (!pcie_link_is_active(pci_dev) && bridge->ops->start_link) {
+ ret = bridge->ops->start_link(bus);
+ if (ret)
+ goto power_off;
+ }
+
+ ret = devm_pci_pwrctrl_device_set_ready(dev, &ctx->pwrctrl);
+ if (ret)
+ goto power_off;
+
+ platform_set_drvdata(pdev, ctx);
+
+ return 0;
+
+power_off:
+ tc9563_pwrctrl_power_off(ctx);
+remove_i2c:
+ i2c_unregister_device(ctx->client);
+ i2c_put_adapter(ctx->adapter);
+ return ret;
+}
+
+static void tc9563_pwrctrl_remove(struct platform_device *pdev)
+{
+ struct tc9563_pwrctrl_ctx *ctx = platform_get_drvdata(pdev);
+
+ tc9563_pwrctrl_power_off(ctx);
+ i2c_unregister_device(ctx->client);
+ i2c_put_adapter(ctx->adapter);
+}
+
+static const struct of_device_id tc9563_pwrctrl_of_match[] = {
+ { .compatible = "pci1179,0623"},
+ { }
+};
+MODULE_DEVICE_TABLE(of, tc9563_pwrctrl_of_match);
+
+static struct platform_driver tc9563_pwrctrl_driver = {
+ .driver = {
+ .name = "pwrctrl-tc9563",
+ .of_match_table = tc9563_pwrctrl_of_match,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+ .probe = tc9563_pwrctrl_probe,
+ .remove = tc9563_pwrctrl_remove,
+};
+module_platform_driver(tc9563_pwrctrl_driver);
+
+MODULE_AUTHOR("Krishna chaitanya chundru <quic_krichai@quicinc.com>");
+MODULE_DESCRIPTION("TC956x power control driver");
+MODULE_LICENSE("GPL");