diff mbox series

[2/2] media: i2c: imx290: Check for availability in probe()

Message ID 20240807-imx290-avail-v1-2-666c130c7601@skidata.com
State New
Headers show
Series media: i2c: imx290: check for availability in probe() | expand

Commit Message

Benjamin Bara Aug. 7, 2024, 8:10 a.m. UTC
Currently, the V4L2 subdevice is also created when the device is not
available/connected. In this case, dmesg shows the following:

[   10.419510] imx290 7-001a: Error writing reg 0x301c: -6
[   10.428981] imx290 7-001a: Error writing reg 0x3020: -6
[   10.442712] imx290 7-001a: Error writing reg 0x3018: -6
[   10.454018] imx290 7-001a: Error writing reg 0x3020: -6

which seems to come from imx290_ctrl_update() after the subdev init is
finished. However, as the errors are ignored, the subdev is initialized
but simply does not work. From userspace perspective, there is no
visible difference between a working and not-working subdevice (except
when trying it out or watching for the error message).

This commit adds a simple availability check before starting with the
subdev initialization to error out instead.

Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
---
 drivers/media/i2c/imx290.c | 5 +++++
 1 file changed, 5 insertions(+)

Comments

Alexander Stein Aug. 7, 2024, 8:33 a.m. UTC | #1
Hi Benjamin,

Am Mittwoch, 7. August 2024, 10:10:28 CEST schrieb Benjamin Bara:
> Currently, the V4L2 subdevice is also created when the device is not
> available/connected. In this case, dmesg shows the following:
> 
> [   10.419510] imx290 7-001a: Error writing reg 0x301c: -6
> [   10.428981] imx290 7-001a: Error writing reg 0x3020: -6
> [   10.442712] imx290 7-001a: Error writing reg 0x3018: -6
> [   10.454018] imx290 7-001a: Error writing reg 0x3020: -6
> 
> which seems to come from imx290_ctrl_update() after the subdev init is
> finished. However, as the errors are ignored, the subdev is initialized
> but simply does not work. From userspace perspective, there is no
> visible difference between a working and not-working subdevice (except
> when trying it out or watching for the error message).
> 
> This commit adds a simple availability check before starting with the
> subdev initialization to error out instead.

There is already a patch reading the ID register at [1]. This also reads the
ID register. But I don't have any documentation regarding that register,
neither address nor values definitions. If there is known information about
that I would prefer reading the ID and compare it to expected values.

Best regards,
Alexander

[1] https://gitlab.com/ideasonboard/nxp/linux/-/commit/85ce725f1de7c16133bfb92b2ab0d3d84efcdb47

> Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
> ---
>  drivers/media/i2c/imx290.c | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index 4150e6e4b9a6..a86076e42a36 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -1580,6 +1580,11 @@ static int imx290_probe(struct i2c_client *client)
>  	pm_runtime_set_autosuspend_delay(dev, 1000);
>  	pm_runtime_use_autosuspend(dev);
>  
> +	/* Make sure the sensor is available before V4L2 subdev init. */
> +	ret = cci_read(imx290->regmap, IMX290_STANDBY, NULL, NULL);
> +	if (ret)
> +		goto err_pm;
> +
>  	/* Initialize the V4L2 subdev. */
>  	ret = imx290_subdev_init(imx290);
>  	if (ret)
> 
>
Benjamin Bara Aug. 7, 2024, 8:50 a.m. UTC | #2
Hi!

On Wed, 7 Aug 2024 at 10:43, Sakari Ailus <sakari.ailus@linux.intel.com> wrote:
> Hi,
>
> On Wed, Aug 07, 2024 at 10:33:51AM +0200, Alexander Stein wrote:
> > Hi Benjamin,
> >
> > Am Mittwoch, 7. August 2024, 10:10:28 CEST schrieb Benjamin Bara:
> > > Currently, the V4L2 subdevice is also created when the device is not
> > > available/connected. In this case, dmesg shows the following:
> > >
> > > [   10.419510] imx290 7-001a: Error writing reg 0x301c: -6
> > > [   10.428981] imx290 7-001a: Error writing reg 0x3020: -6
> > > [   10.442712] imx290 7-001a: Error writing reg 0x3018: -6
> > > [   10.454018] imx290 7-001a: Error writing reg 0x3020: -6
> > >
> > > which seems to come from imx290_ctrl_update() after the subdev init is
> > > finished. However, as the errors are ignored, the subdev is initialized
> > > but simply does not work. From userspace perspective, there is no
> > > visible difference between a working and not-working subdevice (except
> > > when trying it out or watching for the error message).
> > >
> > > This commit adds a simple availability check before starting with the
> > > subdev initialization to error out instead.
> >
> > There is already a patch reading the ID register at [1]. This also reads the
> > ID register. But I don't have any documentation regarding that register,
> > neither address nor values definitions. If there is known information about
> > that I would prefer reading the ID and compare it to expected values.
> >
> > Best regards,
> > Alexander
> >
> > [1] https://gitlab.com/ideasonboard/nxp/linux/-/commit/85ce725f1de7c16133bfb92b2ab0d3d84efcdb47
>
> I'd also prefer reading a register and indeed comparing the read value with
> the expected value.

Sure - I can drop the first patch and check if it contains a "1" (standby).
Probably we learn more about the CHIP_ID, then I can switch to it instead.

Best regards
Benjamin

> --
> Regards,
>
> Sakari Ailus
Benjamin Bara Aug. 7, 2024, 11:07 a.m. UTC | #3
Hi!

On Wed, 7 Aug 2024 at 11:50, Laurent Pinchart
<laurent.pinchart@ideasonboard.com> wrote:
> On Wed, Aug 07, 2024 at 10:47:39AM +0200, Benjamin Bara wrote:
> > On Wed, 7 Aug 2024 at 10:33, Alexander Stein wrote:
> > > Am Mittwoch, 7. August 2024, 10:10:28 CEST schrieb Benjamin Bara:
> > > > Currently, the V4L2 subdevice is also created when the device is not
> > > > available/connected. In this case, dmesg shows the following:
> > > >
> > > > [   10.419510] imx290 7-001a: Error writing reg 0x301c: -6
> > > > [   10.428981] imx290 7-001a: Error writing reg 0x3020: -6
> > > > [   10.442712] imx290 7-001a: Error writing reg 0x3018: -6
> > > > [   10.454018] imx290 7-001a: Error writing reg 0x3020: -6
> > > >
> > > > which seems to come from imx290_ctrl_update() after the subdev init is
> > > > finished. However, as the errors are ignored, the subdev is initialized
> > > > but simply does not work. From userspace perspective, there is no
> > > > visible difference between a working and not-working subdevice (except
> > > > when trying it out or watching for the error message).
> > > >
> > > > This commit adds a simple availability check before starting with the
> > > > subdev initialization to error out instead.
> > >
> > > There is already a patch reading the ID register at [1]. This also reads the
> > > ID register. But I don't have any documentation regarding that register,
> > > neither address nor values definitions. If there is known information about
> > > that I would prefer reading the ID and compare it to expected values.
> >
> > Thanks for the link - it seems like Laurent has dropped the patch for
> > the more recent kernel versions on their GitLab.
>
> It was a patch that I wrote as a test, and I decided not to upstream it
> as it had limited value to me. The downside with reading registers at
> probe time is that you have to power up the sensor. This can have
> undesired side effects, such as flashing a privacy LED on at boot time
> in devices that have one. There's also the increase in boot time due to
> the power up sequence, which one may want to avoid.
>
> The imx290 driver already powers up the device unconditionally at probe
> time, so reading the version register wouldn't be much of an issue I
> suppose. I would be fine merging that patch.
>
> > This was also my initial intention, but similar to you, I don't have a
> > docu describing this register, so I am not sure where the info is coming
> > from and if it really contains the identification/type info. Probably
> > Laurent has more infos on that.
>
> That's a good question. I don't see a mention of that register in the
> IMX290 datasheet I've found online
> (https://static6.arrow.com/aropdfconversion/c0c7efde6571c768020a72f59b226308b9669e45/sony_imx290lqr-c_datasheet.pdf).
> Looking at the git history, the IMX290_CHIP_ID register macro was
> introduced in an unrelated commit, without an explanation. I don't
> recall where it comes from, but I don't think I've added it randomly. It
> may have come from an out-of-tree driver.

Thanks for the info!

> I don't have an IMX290 plugged in at the moment, what's the value of the
> register ?

I currently have an imx462 available, which is not "officially supported" yet,
but basically an imx290 derivative. With your patch applied:

[   10.424187] imx290 7-001a: chip ID 0x07d0

Best regards
Benjamin

>
> > > [1] https://gitlab.com/ideasonboard/nxp/linux/-/commit/85ce725f1de7c16133bfb92b2ab0d3d84efcdb47
> > >
> > > > Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
> > > > ---
> > > >  drivers/media/i2c/imx290.c | 5 +++++
> > > >  1 file changed, 5 insertions(+)
> > > >
> > > > diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> > > > index 4150e6e4b9a6..a86076e42a36 100644
> > > > --- a/drivers/media/i2c/imx290.c
> > > > +++ b/drivers/media/i2c/imx290.c
> > > > @@ -1580,6 +1580,11 @@ static int imx290_probe(struct i2c_client *client)
> > > >       pm_runtime_set_autosuspend_delay(dev, 1000);
> > > >       pm_runtime_use_autosuspend(dev);
> > > >
> > > > +     /* Make sure the sensor is available before V4L2 subdev init. */
> > > > +     ret = cci_read(imx290->regmap, IMX290_STANDBY, NULL, NULL);
> > > > +     if (ret)
> > > > +             goto err_pm;
> > > > +
> > > >       /* Initialize the V4L2 subdev. */
> > > >       ret = imx290_subdev_init(imx290);
> > > >       if (ret)
diff mbox series

Patch

diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
index 4150e6e4b9a6..a86076e42a36 100644
--- a/drivers/media/i2c/imx290.c
+++ b/drivers/media/i2c/imx290.c
@@ -1580,6 +1580,11 @@  static int imx290_probe(struct i2c_client *client)
 	pm_runtime_set_autosuspend_delay(dev, 1000);
 	pm_runtime_use_autosuspend(dev);
 
+	/* Make sure the sensor is available before V4L2 subdev init. */
+	ret = cci_read(imx290->regmap, IMX290_STANDBY, NULL, NULL);
+	if (ret)
+		goto err_pm;
+
 	/* Initialize the V4L2 subdev. */
 	ret = imx290_subdev_init(imx290);
 	if (ret)